warning Peugeot 406 2002.5 Owner's Guide

THE KEYS
The keys allow you to switch on the
ignition and to independently operate
the locks on the front door, the glove
box and the passenger air bag dis
arming switch.
Central locking
From the driver's door, the keys
allow you to lock, deadlock* and
unlock the doors and boot/tailgate.
If one of the front doors is open, the
central locking does not work.
The remote control performs the
same functions at a distance.
The remote control
Locking
Press button Ato lock the vehicle.
YOUR 406 IN DETAIL 105
This is confirmed by fixed lighting of
the direction indicators for approxi
mately two seconds.
Unlocking
Press button
B to unlock the vehicle.
This is confirmed by rapid flashing of
the direction indicators.
Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You risk caus
ing it not to work and the remote con
trol would have to be reprogrammed. ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management
system as soon as the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly,
an audible signal sounds,
accompanied by a message on the
multifunction display.
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible.
Locating your car
To locate your car, if you have locked
it, in a car park: 
press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition.
29-07-2002

29-07-2002
SPECIAL FEATURES
170
THE ALARM SYSTEM
Setting and disarming the
alarm
Setting and deactivating the alarm
The alarm completes the security
equipment for your vehicle. It offers
two types of protection. exterior protection: when it is set,
the alarm sounds if a door, the
boot or the bonnet is opened;
interior protection: when it is set,
the alarm sounds if the sensors
detect a variation in the air move
ment inside the vehicle (break
ing of a window) or movement
inside the vehicle.
The alarm is also equipped with an
antitamper function.
The alarm is also equipped with an
antitamper function.
If an attempt is made to tamper with
the wires to the siren, control unit or
the battery, the alarm is triggered:
the siren sounds and the headlamps
come on. Setting the alarm
(interior and exterior protection)
Switch the ignition off and get out
of the vehicle.
Press the locking button of the remote
control key.
The doors lock.
The direction indicators light for two
seconds.
The red light on the switch flashes once
a second.
5 seconds later, exterior protection is set.
50 seconds later, interior protection is set.
Note:
when the alarm is triggered, the
siren sounds for thirty seconds. After
the thirty seconds it stops, but the
alarm remains set.
Warning
If, on setting the alarm, a door, the boot
or the bonnet are not closed correctly,
the siren sounds for a moment. If the
vehicle is closed correctly in the follow
ing 45 seconds, the alarm is set and
the direction indicators remain on for
two seconds. In all cases, the alarm is
set after 45 seconds. Disarming the alarm
(interior and exterior protection)
Press the unlocking button of the
remote control key.
The doors unlock.
The direction indicators flash for two
seconds.
The red warning light on the switch
goes out.
Note:
if the warning light continues
to flash after disarming the alarm, it
is a sign that the alarm has been trig
gered. The flashing will stop when
the ignition is switched on.

29-07-2002
AUTOMATIC SWITCHING ON
OF THE LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off as soon as the light
becomes bright enough or the wind
screen wipers stop.
This function is active when the vehi
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories
position (1st notch),
 Press the end of the lights stalk
for more than two seconds.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. Because of this, the lights do
not come on automatically.
Do not cover the brightness sen
sor connected to the rain sensor,
located in the windscreen behind
the mirror. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting of
the headlamps activated" on the
multifunction display.
Note: Always operate the lighting
controls manually where this is pos
sible.
Disarming
Disarming of the function is accom
panied by an audible signal.
When driving, if this function is
switched off when the headlamps
would switch on in automatic mode,
the lights remain on.
It is however possible to disarm this
function and switch off the lights by:
manually switching off the lights using the lights stalk,
switching off the engine.
YOUR 406 IN DETAIL 123
If the brightness sensor does not
function correctly, the system acti
vates the function (the lights come
on).The driver is alerted by the flash
ing of the ''dipped beam'' warning
light on the instrument panel.
Contact a PEUGEOT dealer to have
the system checked.
Follow me Home
When there is a low level of bright
ness or at night, if you leave your
vehicle, the side lights and the
dipped beam lights may remain on
for approximately one minute.
To do this: place the lights stalk in the AUTO
position,
 place the key in the accessories
position (first notch),
 press the end of the lights stalk for
more than two seconds,
 place the lights stalk in the 0posi
tion,
 flash the headlamps,
 get out of the car and lock it.

29-07-2002
HORN
Press one of the spokes or
the centre of the steering
wheel.
Adjusting the headlamps
Depending on the load in your vehi
cle, adjusting the beam of the head
lamps is recommended as follows.0 1 or 2 people in the front seats.
– 3 people.
1 5 people.
2 5 people + maximum
authorised load.
3 Driver + maximum
authorised load.
Initial setting is position 0. Hazard warning lights
Press the button, the direction indi
cators flash.
They can operate with the ignition
off.
STEERING WHEEL HEIGHT
AND DEPTH ADJUSTMENT
When the vehicle is stationary,
unlock the steering wheel by pulling
handle
A.
Adjust the height and depth of the
steering wheel, then lock it by push
ing handle Adown fully.
YOUR 406 IN DETAIL
142
Automatic lighting of hazard
warning lights*
When braking in an emergency,
depending on the force of decelera
tion, the hazard warning lights come
on automatically. They switch off
automatically the first time you accel
erate.
It is also possible to switch them off
by pressing the button.* According to destination.

29-07-2002
AIR BAGS
The air bags have been designed to
maximise the safety of the occu
pants in the event of serious colli
sions; they work in conjunction with
the force limiting seat belts.
In the event of a serious collision, the
electronic detectors record and
analyse any abrupt deceleration of
the vehicle: if the triggering threshold
is reached, the air bags inflate
instantly and protect the occupants
of the vehicle.
Immediately after the impact, the air
bags deflate rapidly, so that they do
not hinder the visibility of the occu
pants nor their possible exit from the
vehicle.
The air bags will not be deployed in
collisions which are not serious, for
which the seat belt is sufficient to
provide maximum protection. The
seriousness of the collision depends
on the nature of the obstacle and the
speed of the vehicle at the moment
of impact.
Air bags only operate when the
ignition is switched on.
Note:the gas escaping from the air
bags can be a minor irritant. FRONT AIR BAGS
These are folded in the centre of the
steering wheel for the driver and in
the fascia for the front passenger.
They are deployed simultaneously,
except in cases where the air bag is
disarmed.
Front air bag malfunction
If this warning light comes
on, accompanied by a
buzzer and the message
"Air bag fault" on the multi
function display , contact a
PEUGEOT dealer to have the sys
tem checked.
DRIVING YOUR 406 151
Passenger air bag precautions
For a vehicle fitted with a passenger
air bag disarming switch: disarm the airbag if you install
a rearfacing
child seat on the
front passenger
seat,
arm the air bag for an adult
passenger.
For a vehicle not fitted with a pas
senger air bag disarming switch: do not install a rearfacing child seat on
the front passenger
seat.
Never place your feet or any object
on the fascia.

29-07-2002
Operating check
This is confirmed by an indi
cator light, accompanied
by an audible signal and a
message on the multifunction dis
play.
With the ignition on (2nd notch), illu
mination of this warning light accom
panied by an audible signal and the
message "Passenger air bag dis
armed" on the multifunction display,
indicates that the passenger air bag
is disarmed (switch in the "OFF"
position).
DRIVING YOUR 406
152
Disarming the passenger
air bag*
To ensure the safety of your child,
it is essential to disarm the pas
senger air bag when you install a
rearfacing child seat on the front
passenger seat. With the ignition switched off, insert
the key into the passenger air bag
disarming switch 1, turn it to the
"OFF" position, then remove the
key keeping the slot in this position.
The air bag warning light on the
instrument panel is lit throughout the
disarming process.
In the "OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is removed,
turn the air bag slot to the "ON"posi
tion to reactivate the air bag and
thus ensure the safety of your pas
senger in the event of an impact.
* According to destination. SIDE AIR BAGS
The side air bags are incorporated
into the backs of the front seats, on
the door side.
They are deployed independently of
each other, on whichever side the
collision occurs.
Operating check
This is confirmed by an indicator
light, accompanied by an audible
signal and a message on the multi
function display.
If this indicator light comes
on, accompanied by an
audible signal and the mes
sage "Air bag fault" on
the multifunction display,
contact a PEUGEOT dealer to have
the system checked.

29-07-2002
Operating check
This is confirmed by an indi
cator light, accompanied
by an audible signal and a
message on the multifunction dis
play.
With the ignition on (2nd notch), illu
mination of this warning light accom
panied by an audible signal and the
message "Passenger air bag dis
armed" on the multifunction display,
indicates that the passenger air bag
is disarmed (switch in the "OFF"
position).
DRIVING YOUR 406
152
Disarming the passenger
air bag*
To ensure the safety of your child,
it is essential to disarm the pas
senger air bag when you install a
rearfacing child seat on the front
passenger seat. With the ignition switched off, insert
the key into the passenger air bag
disarming switch 1, turn it to the
"OFF" position, then remove the
key keeping the slot in this position.
The air bag warning light on the
instrument panel is lit throughout the
disarming process.
In the "OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is removed,
turn the air bag slot to the "ON"posi
tion to reactivate the air bag and
thus ensure the safety of your pas
senger in the event of an impact.
* According to destination. SIDE AIR BAGS
The side air bags are incorporated
into the backs of the front seats, on
the door side.
They are deployed independently of
each other, on whichever side the
collision occurs.
Operating check
This is confirmed by an indicator
light, accompanied by an audible
signal and a message on the multi
function display.
If this indicator light comes
on, accompanied by an
audible signal and the mes
sage "Air bag fault" on
the multifunction display,
contact a PEUGEOT dealer to have
the system checked.

29072002
BATTERY
To charge the battery using a battery charger:
Disconnect the battery,
Follow the instructions for use given by the battery charger manufacturer,
Reconnect starting with the negative (–) terminal,
Check that the terminals and connectors are clean. If they are covered with sul
phate (white or greenish deposit), disconnect them and clean t hem.
To start the vehicle from another battery:
Connect the red cable to the positive (+) terminals of the tw o batteries,
Connect one end of the green or black cable to the negat ive (–) terminal of the
slave battery,
Connect the other end of the green or black cable to an e arth point on the bro
ken down vehicle, as far as possible from the battery,
Operate the starter, let the engine run.
Wait for the engine to return to idle, then disconnect th e cables.
Never disconnect a terminal when the engine is running.
Never charge a battery without first disconnecting the terminal s.
Close the sunroof before disconnecting the battery. If it does not
operate normally following reconnection of the battery, you must
reinitialise it by turning the control to the maximum tilt po sition and pressing
it for a few seconds.
After every reconnection of the battery, switch on the igniti on and wait
1 minute before starting to allow the electronic systems to be initialised. If
slight difficulties are experienced after this, please contact a PEUGEOT
dealer. It is advisable to disconnect the battery if the vehicle
is not to be used for a period of more than one month.Economy mode
With the engine switched off and the
ignition key in the "running" or
"accessories" position for about half
an hour, certain electrical equipment
(displays, instrument panel, warning
lights, courtesy lights, electric win
dows, wipers etc.) will switch off
automatically to avoid draining the
battery.
Once the electrical equipment goes
into economy mode, it is necessary
to start the engine to enable the
equipment to work again.
MAINTENANCE OF YOUR 406
46

29-07-2002
TOWING A TRAILER,
CARAVAN, BOAT ETC.
Only use original PEUGEOT tow
bars that have been tested and
approved from the design stage of
your vehicle.
The tow bar must be fitted by a
PEUGEOT dealer.
Your vehicle is basically designed for
transporting people and luggage but
it may also be used for towing a
trailer.
Driving with a trailer subjects the
towing vehicle to more significant
stress and its driver must be particu
larly careful.
Air density decreases with altitude,
thus reducing engine performance.
The maximum towing load must
be reduced by 10% for every
1000 metres of altitude.
Driving advice
Distribution of loads:
Distribute the load in the trailer so
that the heaviest items are as close
as possible to the axle and the nose
weight approaches the maximum
permitted without exceeding it. Cooling:
Towing a trailer on a slope increases
the temperature of the coolant.
As the fan is electrically controlled,
its cooling capacity is not dependent
on the engine speed.
On the contrary, use a high gear to
lower the engine speed, and reduce
your speed.
The maximum towing speed on a
long slope depends on the gradient
and the outside temperature.
For vehicles fitted with a direct injec
tion petrol engine, after towing or dri
ving at high speed for a long period
of time, the fan may operate for
approximately 6 minutes.
In all cases, pay attention to the
coolant temperature.
If the warning light comes on, stop
the vehicle and switch off the engine
as soon as possible.
Tyres:
Check the tyre pressures of the tow
ing vehicle and the trailer, observing
the recommended pressures.
Brakes:
Towing increases the braking distance.
Lights:
Check the electrical signalling on the
trailer.
Side wind:
Take into acount the increased sen
sitivity to side wind.
MAINTENANCE OF YOUR 406
49