wheel PEUGEOT 5008 2010.5 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010.5, Model line: 5008, Model: PEUGEOT 5008 2010.5Pages: 345, PDF Size: 22.77 MB
Page 213 of 345
PRACTICAL INFORMATION
179
Other accessories Wheel with trim
When removing the wheel ,
d e t a c h t h e t r i m fi r s t u s i n g t h e
wheelbrace 1 pulling at the valve
passage hole.
W h e n r e fi t t i n g t h e w h e e l , r e fi t t h e
trim starting by placing its notch fac-
ing the valve and press around its
edge with the palm of your hand.
8. Removable towing eye.
Refer to "Electric parking brake"
in the "Driving" section.
Refer to the paragraph "Towing
the vehicle".
9. Electric parking brake emergency
release control.
Page 214 of 345
PRACTICAL INFORMATION
180
Access to the spare wheel *
The spare wheel is supported by a
cable-driven carrier underneath the
vehicle. Taking out the wheel
Raise the concertina board to reveal
the spare wheel carrier drive nut.
Turn this drive nut fully clockwise,
using the wheelbrace 1 and the ex-
tension 7 , to unwind the carrier cable.
Detach the wheel/box assembly
from the rear of the vehicle.
Remove the hook with its connection
plate to release the wheel/box as-
sembly, as shown in the illustration.
Pull out the wheel to gain access to
the box.
Slide the box cover to the centre
and remove it to gain access to the
other tools.
* Depending on destination country.
Page 215 of 345
PRACTICAL INFORMATION
181
T y r e u n d e r - i n fl a t i o n
detection
T h e s p a r e w h e e l i s n o t fi t t e d
with a sensor. The punctured wheel
must be repaired by a PEUGEOT
dealer. Putting the wheel back in place
Store the tools used in the box and
close the cover.
Position the box on the ground and
centre the spare wheel on it.
Pass the hook with its connection
plate into the wheel then the box, as
illustrated.
Raise the wheel/box assembly un-
derneath the vehicle by turning the
carrier drive nut anticlockwise using the
wheelbrace 1 and the extension 7 .
Tighten fully and check that the
w h e e l i s h o r i z o n t a l l y fl u s h a g a i n s t
t h e fl o o r .
Page 216 of 345
PRACTICAL INFORMATION
182
Parking the vehicle
Immobilise the vehicle where
i t d o e s n o t b l o c k t r a f fi c : t h e
ground must be level, stable and
non-slippery ground.
Apply the parking brake unless it
has been programmed to automatic
mode, switch off the ignition and en-
g a g e fi r s t g e a r * t o l o c k t h e w h e e l s .
Check that the braking warning lamp
and the P warning lamp on the park-
ing brake control come on.
If necessary, place a chock under the
wheel diagonally opposite the wheel
to be changed.
The occupants must get out of the ve-
hicle and wait where they are safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Removing a wheel
List of operations
Remove the chromed bolt cover
from each of the bolts using the
tool 3 (according to equipment).
Fit the security socket 5 on the
wheelbrace 1 to slacken the security
bolt (if your vehicle has them).
Slacken the other bolts using the
wheelbrace 1 only.
Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underbody, which-
ever is closest to the wheel to be
changed.
Extend the jack 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.
Raise the vehicle until there is suf-
fi c i e n t s p a c e b e t w e e n t h e w h e e l a n d
the ground to admit the spare (not
punctured) wheel easily.
Remove the bolts and store them in
a clean place.
Remove the wheel.
* position R for the electronic gear
control manual gearbox; P for the
automatic gearbox.
Page 217 of 345
PRACTICAL INFORMATION
After changing a wheel
To store the punctured wheel in the boot
c o r r e c t l y , fi r s t r e m o v e t h e c e n t r a l c o v e r .
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80 km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a PEUGEOT dealer without delay.
Have the punctured wheel repaired
and replace it on the vehicle as soon
as possible.
Fitting a wheel
List of operations
Put the wheel in place on the hub
using the centring guide 4 .
Screw in the bolts by hand to the
stop.
Using the wheelbrace 1 fi t t e d w i t h
the security socket 5 , pre-tighten
the security bolt (if your vehicle has
them).
Pre-tighten the other bolts using the
wheelbrace 1 only.
Lower the vehicle fully.
Fold the jack 2 and detach it.
Using the wheelbrace 1 fi t t e d w i t h
the security socket 5 , tighten the
security bolt (if your vehicle has
them).
Tighten the other bolts using the
wheelbrace 1 only.
R e fi t t h e c h r o m e d b o l t c o v e r s o n
each of the bolts (according to
equipment).
Store the tools in the box.
Fitting the "space-saver"
spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a l -
loy wheels, when tightening the bolts
o n fi t t i n g i t i s n o r m a l t o n o t i c e t h a t t h e
washers do not come into contact
with the "space-saver" spare wheel.
The wheel is secured by the conical
contact of each bolt.
Page 233 of 345
PRACTICAL INFORMATION
199
TOWING THE VEHICLE
Procedure for having your vehicle towed
or for towing another vehicle using a re-
movable towing eye.
Access to the tools Towing your vehicle
On the front bumper, unclip the cover
by pressing at the bottom.
Screw the towing eye in fully.
Install the towing bar.
Switch on the hazard warning lamps
on the towed vehicle.
On the rear bumper, unclip the cover
by pressing at the bottom.
Screw the towing eye in fully.
Install the towing bar.
Switch on the hazard warning lamps
on the towed vehicle.
Towing another vehicle
The towing eye is installed under the
left-hand concertina board, in the boot
interior trim.
To gain access to it:
open the boot,
raise the concertina board,
remove the towing eye from the
holder. When towing with all four
wheels on the ground, always
use a towing bar.
When towing with only two wheels on
the ground, always use professional
lifting equipment.
When towing with the engine off,
there is no longer any braking or
steering assistance.
Place the gear lever in neu-
tral (position N on the elec-
tronic gear control gearbox
or automatic gearbox).
Failure to observe this special condi-
tion could result in damage to certain
braking components and the absence
of braking assistance the next time
the engine is started.
Page 238 of 345
PRACTICAL INFORMATION
203
"Multimedia":
a u d i o s y s t e m s , a m p l i fi e r s , s a t e l l i t e n a v i -
gation systems, Bluetooth hands-free
system, CD changer, speakers, DVD
player, USB Box, front and rear parking
sensors, additional Bluetooth wireless
headphones, Bluetooth audio head-
phones mains charger. Installation of radio
communication
transmitters
Before installing on your vehicle
any after-market radio communica-
tion transmitter with external aerial,
we recommend that you contact a
PEUGEOT dealer.
The PEUGEOT dealer network will give
y o u t h e s p e c i fi c a t i o n f o r t r a n s m i t t e r s
w h i c h c a n b e fi t t e d ( f r e q u e n c y , m a x i -
m u m p o w e r , a e r i a l p o s i t i o n , s p e c i fi c i n -
stallation requirements), in line with the
Vehicle Electromagnetic Compatibility
Directive (2004/104/EC).
"Protection":
mats * , boot tray, luggage net, coat hanger
fi x e d o n h e a d r e s t r a i n t , s t a i n l e s s s t e e l o r
carbon door sills.
* To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
ACCESSORIES
A wide range of accessories and genu-
ine parts is offered by the PEUGEOT
dealer network.
These accessories and parts have been
tested and approved for reliability and
safety.
They are all adapted to your vehicle and
b e n e fi t f r o m P E U G E O T ' s r e c o m m e n d a -
tion and warranty.
"Safety and security":
anti-theft alarm, window etching, wheel
s e c u r i t y b o l t s , fi r s t a i d k i t , w a r n i n g t r i -
angle, high visibility vest, stolen vehi-
cle tracking system, dog guard, snow
chains.
"Style":
seat covers compatible with lateral air-
bags, leather gear lever knob, foglamps,
d o o r d e fl e c t o r s , s p o i l e r , s t y l i n g s t r i p s ,
alloy wheels, trims, chrome-plated door
handle shells. Depending on the legislation
in force in the country, it may
be compulsory to have a high
visibility safety vest, warning triangle
and spare bulbs and fuses available
in the vehicle.
T h e fi t t i n g o f e l e c t r i c a l e q u i p -
ment or accessories which
are not recommended by
PEUGEOT may result in a failure of
your vehicle's electronic system and
excessive electrical consumption.
P l e a s e n o t e t h i s s p e c i fi c w a r n i n g . Y o u
are advised to contact a PEUGEOT
representative to be shown the range
of recommended equipment and
accessories.
"Transport solutions":
For leisure pursuits: roof bars, bicycle
carrier on towbar, bicycle carrier on roof
bars, ski carrier, roof box, booster seats
and child seats, side blinds, under shelf
storage.
T r a i l e r t o w b a r , w h i c h m u s t b e fi t t e d b y a
PEUGEOT dealer.
You can also obtain cleaning and main-
tenance products (exterior and interior),
products for topping up (screenwash
fl u i d . . . ) a n d r e fi l l s ( s e a l a n t c a r t r i d g e
for the temporary puncture repair kit...)
from PEUGEOT dealers.
Page 247 of 345
TECHNICAL DATA
212
IDENTIFICATION MARKINGS
V a r i o u s v i s i b l e m a r k i n g s f o r t h e i d e n t i fi -
cation and tracing of your vehicle. I f t h e i n fl a t i o n p r e s s u r e s a r e
too low, this increases fuel
consumption.
T h e i n fl a t i o n p r e s s u r e s m u s t
be checked when the tyres are
cold, at least once a month.
A. V e h i c l e I d e n t i fi c a t i o n N u m b e r
(VIN) under the bonnet.
This number is engraved on the bodywork near the damper support.
B. V e h i c l e i d e n t i fi c a t i o n N u m b e r
(VIN) on the windscreen lower
crossmember.
This number is indicated on a self- adhesive label which is visible
through the windscreen.
C. Manufacturer’s label.
The VIN is indicated on a self- d e s t r o y i n g l a b e l a f fi x e d t o t h e d o o r
aperture, on the right-hand side.
D. Tyre/paint label.
T h i s l a b e l i s a f fi x e d t o t h e d o o r aperture, on the driver’s side.
It bears the following information:
- t h e t y r e i n fl a t i o n p r e s s u r e s w i t h a n d without load,
- the wheel rim and tyre sizes,
- the brands of tyre recommended by the manufacturer,
- t h e i n fl a t i o n p r e s s u r e o f t h e s p a r e wheel,
- the paint colour code.