ignition Peugeot 508 2011 Service Manual

4
121
i
i
Driving





Speed limiter


System which prevents the vehicle from
exceeding the speed programmed by the driver.
When the programmed speed limit is reached,
pressing the accelerator pedal no longer
has any effect unless it is pressed firmly,
which allows you to temporarily exceed the
programmed speed.
To return to the programmed speed, simply
slow down to a speed below the programmed
speed by releasing the accelerator.
The speed limiter is switched on
manually: it
requires a programmed speed of at least
20 mph (30 km/h).
The speed limiter is switched off
by manual
operation of the control.
The programmed speed remains in the memory
when the ignition is switched off.

The speed limiter cannot, in any
circumstances, replace the need to
obser ve speed limits, nor can it replace
the need for vigilance and responsibility
on the par t of the driver.






This information also appears in the
head-up display.
For more information on the head-up
display, refer to the relevant page in this
"Driving" section.

1.
Speed limiter mode selection button

2.
Programmed value decrease button

3.
Programmed value increase button

4.
Suspend/restore speed limiter (pause)

5.
Speed limiter off button


Steering mounted controls

The programmed information is grouped
together in the instrument panel screen.

Displays in the instrument panel



A.
Speed limiter on/pause indication

B.
Speed limiter mode selection indication

C.
Programmed speed value

4
123
i
i
Driving





Cruise control

System which automatically maintains the
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
The cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph
(40 km/h) and the engaging:


- 4th gear or higher on a manual gearbox,

- 2nd gear or higher on an electronic gear
control gearbox or automatic gearbox,

- position A
on the electronic gear control
gearbox or D
on the automatic gearbox.
The cruise control is switched off
manually
or by pressing the brake or clutch pedal or
on triggering of the ESP system for safety
reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.

1.
Cruise control mode selection button

2.
Speed programming/programmed value
decrease button

3.
Speed programming/programmed value
increase button

4.
Cruise control suspension/resume button
(pause)

5.
Cruise control off button

Steering mounted controls

The cruise control cannot, in any
circumstances, replace the need to
obser ve speed limits, nor can it replace
the need for vigilance and responsibility
on the par t of the driver.





This information also appears in the
head-up display.
For more information on the head-up
display, refer to the relevant page in this
"Driving" section. The programmed information is grouped
together in the instrument panel screen.

Displays in the instrument panel



A.
Cruise control on/pause indication

B.
Cruise control mode selection indication

C.
Programmed speed value

128
i !
Driving

Operation

When you have identified a parking space:


)
Engage a gear on a manual gearbox or put
the gear lever in position A
(electronic gear
control gearbox) or in position D
(automatic
gearbox).

)
Press button A
to star t the system.

)
Operate the direction indicator on the
side where the space is to be measured;
a message is displayed and the warning
lamp flashes to confirm that measurement
is in progress.

)
During measurement, go for ward the
length of the space, at a speed less than
12 mph (20 km/h), to prepare for your
manoeuvre.

)
Once the measurement has been
completed, the system informs you of
the level of difficulty of the manoeuvre
by a message in the multifunction screen
accompanied by an audible signal.

The system displays one of the following messages:


Parking possible


Parking difficult


Parking not advised


If the lateral distance between your
vehicle and the parking space is too
great, the system may not be able to
measure the space.

The system remains available after
each measurement and can therefore
measure several spaces in succession.
In poor or wintry weather, ensure that
the sensors are free of dir t, ice or snow.
The parking space sensor system
deactivates the front parking sensors
when measuring for wards.
If there is a fault, have the system
checked by a PEUGEOT dealer or a
qualified workshop.
The system switches itself off automatically:


- when you engage reverse gear,

- when you switch off the ignition,

- if measuring is not requested,

- within five minutes of switching on the
system,

- if the vehicle speed exceeds the threshold
of 45 mph (70 km/h) for one minute.

132
i
ii
Visibility

Lighting left on audible
signal
An audible signal when a front door
is opened warns the driver that the
vehicle's exterior lighting is on, with the
ignition off and in manual lighting mode.
In this case, switching off the lighting
stops the audible signal.
With the ignition off, if the dipped
headlamps remain on, the vehicle goes
into "ECO" mode to avoid discharging
the battery. In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
Daytime lighting, compulsory in cer tain
countries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other road users.






Daytime running lamps


This function is assured:


- in countries where it is imposed by
regulations, by illumination of the dipped
beam headlamps with the sidelamps and
number plate lamps.

- for other countries where it is provided, by
the use of dedicated lamps.
This function can be activated
or deactivated via the vehicle
configuration menu.

The lighting goes off when you switch
off the ignition, but you can always
switch it on again using the lighting
control stalk.

5
133
Visibility


















Parking lamps

Side markers for the vehicle by illumination of
the sidelamps on the traffic side only.


)
Within one minute of switching off the
ignition, operate the lighting control stalk up
or down depending on the traffic side (for
example: when parking on the left; lighting
control stalk upwards; the right hand
sidelamps are on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator warning lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to position 0 or switch on
the ignition. Temporarily keeping the dipped beam
headlamps on after the vehicle's ignition has
been switched off makes the driver's exit easier
when the light is poor.






Manual guide-me-home
lighting

Switching on



)
Within 30 seconds or a minute after
switching of the ignition (according to the
automatic guide-me-home lighting duration
programmed in the configuration menu),
"flash" the headlamps using the lighting
stalk.

)
A fur ther "headlamp flash" switches the
function off.



Switching off

The manual guide-me-home lighting switches
off automatically after a set time.

5
135
i
i
Visibility

Adaptive lighting


Switching on

The driver can take over at any time, if the
circumstances dictate: System which automatically changes between
dipped and main beam according to the driving
conditions, using a sensor in the rear view
mirror.
The system is active from 15 mph (25 km/h)
and is deactivated below 9 mph (15 km/h).


)
put the lighting control stalk on the "AUTO"
or "Dipped/main beam headlamps"
position,

Switching off


)
or by dipping the headlamps manually
using the lighting control stalk, whether
in the "AUTO" or "Dipped/main beam
headlamps" position.


Flashing the headlamps does not
deactivate the system.
The state of the system is stored in
memory when switching off the ignition.
This automatic headlamp dipping
system is a driving aid. The driver
remains responsible for the vehicle's
lighting and its correct use for the
prevailing conditions of light, visibility
and traffic.
The system may suffer inter ference or
not work correctly:


- under conditions of poor visibility
(for example, snowfall, heavy rain
or thick fog, ...),

- if the windscreen is dir ty, misted or
obscured (by a sticker, ...) in front of
the sensor,

- if the vehicle is facing highly
reflective signs.


The system is not able to detect:


- road users that do not have their
own lighting, such as pedestrians,

- road users whose lighting is
obscured, such as vehicles running
behind a safety barrier (on a
motor way, for example),

- road users at the top or bottom of
a steep slope, on twisty roads, on
crossroads.



)
press this button, the
warning lamp goes off,

)
press this button, the
warning lamp comes on.

136
!
Visibility





Exterior welcome
lighting
Remote switching on of the lighting makes your
approach to the vehicle easier in poor light. It is
activated according to the level of light detected
by the sunshine sensor.

Switching on

Switching off


The exterior welcome lighting switches off
automatically after a set time, when the ignition
is switched on or on locking the vehicle.



Programming


The lighting duration is selected
via the instrument panel screen
configuration menu.
The duration of the welcome lighting is
associated with and identical to that of
the automatic guide-me-home lighting.



)
Press the open padlock on the
remote control.
The dipped beam headlamps
and the sidelamps come on; your
vehicle is also unlocked.










Door mirror spotlamps


Switching on

The spotlamps come on:


- when you unlock the vehicle,

- when you remove the key from the ignition,

- when you open a door,

- when you use the remote control.



Switching off

They are timed to go off automatically. To make your approach to the vehicle easier,
these illuminate:


- the zones facing the driver’s and
passenger’s doors,

- the zones for ward of the door mirrors and
rear ward of the front doors.

138
i
Visibility

When the dipped or main beam headlamps
are on, this function enables the light beams to
provide improved lighting of the side of the road
when cornering.
The use of this function, associated with the
xenon headlamps only, considerably improves
the quality of your lighting when cornering.








Main directional lighting


with directional lighting


without directional lighting





Programming

Operating fault

The function is activated or
deactivated via the configuration
menu (in the instrument panel
screen).
When stationary or moving at very low
speed or when reverse gear is engaged,
the function is inactive.
The status of the function remains in the
memory when the ignition is switched off. If a fault occurs, this warning lamp
flashes in the instrument panel,
accompanied by a message in the
instrument panel screen.
Contact a PEUGEOT dealer or a
qualified workshop.

5
141
!
Visibility












Rear wiper

If a significant accumulation of snow or
ice is present, or when using a bicycle
carrier on the boot, deactivate the
automatic rear wiper via the instrument
panel screen configuration menu. Rear wiper selection ring: park,
intermittent wipe,
wash-wipe (set duration).


Reverse gear

When reverse gear is engaged, the rear wiper
will come into operation if the windscreen
wipers are operating.
The function is activated or
deactivated via the instrument panel
screen configuration menu.
This function is activated by default.



Programming



)
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
windscreen wipers operate for a fixed
period.
The headlamp washers only operate when the
dipped beam headlamps are on
.










Windscreen and headlamp
wash










Screenwash/headlamp wash
level low
In the case of vehicles fitted
with headlamp washers, when
the fluid reser voir low level
is reached this warning lamp comes on in the
instrument panel, accompanied by an audible signal
and a message in the instrument panel screen.
The warning lamp comes on when the ignition is
switched on, or every time the stalk is operated,
until the reser voir is refilled.
Next time you stop, refill the screenwash/headlamp
wash reservoir.

142
i
Visibility











Automatic rain sensitive
windscreen wipers
The windscreen wipers operate automatically,
without any action on the par t of the driver, if
rain is detected (sensor behind the rear view
mirror), adapting their speed to the intensity of
the rainfall.

Switching on

Briefly push the control stalk
downwards.
This warning lamp comes on in the
instrument panel and a message
appears in the multifunction screen. Briefly push the control stalk
downwards again, or place the
control stalk in another position
(Int, 1 or 2).
This warning lamp goes off in the instrument panel
and a message appears in the multifunction screen.


Switching off


The automatic rain sensitive windscreen
wipers must be reactivated by pushing
the control stalk downwards, if the
ignition has been off for more than
one minute.