ignition Peugeot 607 Dag 2002 User Guide

INSTRUMENTS AND CONTROLS31
Coolant temperature warning light
This symbol is accompanied by an audible signal and the message
'Engine temperature too high'
on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Warning: wait for the engine to cool.
If necessary, top up the level.
With the engine running and the vehicle moving
The instrument panel display temporarily shows:
– lights indicating warnings, when these occur,
– vehicle function status indicator lights, when a change occu rs.
Certain warning lights may be accompanied by an audib le signal and a
message on the multifunction display.
List of warning symbols MANUAL CHECK
(vehicle autotest)
 Press the "CHECK"button on
the instrument panel.
With the ignition key in the acces
sories position, with the ignition
switched on, with the engine running
or when the vehicle is moving, this
function informs you at all times of
the following: – any current warnings,
– the status of functions which it is possible to switch on or off (wind
screen wipers, automatic switch
ing on of lights, cruise control, dis
arming of passenger air bag, etc.).
The corresponding warning lights
are displayed in succession on the
instrument panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator lights will be
displayed at the end of this mode.
CHECK mode entry indi
cator light (vehicle
autotest)
This comes on when you
press the 'CHECK' button.
CHECK mode exit indica
tor light (vehicle autotest)
This comes on at the end of
the CHECK mode.
Engine oil pressure warning light
This symbol is accompanied by an audible signal and the message
'Insufficient engine oil pressure' or 'Engine oil pressure too low' on
the multifunction display.
It is linked to the STOPwarning light.
Stop immediately if this comes on when the engine is running.
If there is a lack of oil in the lubrication circuit, top up the level.
Contact a PEUGEOT dealer as soon as possible.
Puncture warning light
This symbol comes on accompanied by an audible signal and the me s
sage 'Punctured tyre(s) detected' on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Change the damaged wheel.
Have it repaired by a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS
32
STOP warning light
This comes on after the
engine oil pressure, coolant temperature orpuncture warning lights, to which it is linked.
Stop immediately. Contact a PEUGEOT dealer.
Brake fluid level and brake force distribution fault warn ing light
This is linked to the light on the instrument panel.
Display of this warning light accompaned by an audible signa l and the message 'Brake fluid low'indicates an
excessive drop in the brake fluid level.
Display of this warning light, accompanied by an audible sig nal and the message 'Braking system faulty' on the multifunc
tion display indicates a malfunction of the brake force distrib ution system.
Stop immediately in both cases. Contact a PEUGEOT dealer.
Dynamic stability control (ESP/ASR) warning light
Display of this warning light, accompanied by an audible sig nal and the message 'ESP/ASR system faulty' on the
multifunction display indicates a system malfunction.
Contact a PEUGEOT dealer.
Handbrake warning light
Display of this warning light, accompanied by an audible sig nal (vehicle moving) and the message 'Handbrake on'
on the multifunction display, indicates that the handbrake is applied or has not been released correctly.
Battery charge warning light
This comes on each time the ignition key is in the accessories posi tion (1st notch).
Display of this warning light when the engine is running is accompanied by an audible signal and the message 'Bat
tery charge fault' on the multifunction display.
This can indicate:
– faulty operation of the charging circuit,
– loose battery or starter terminals,
– a cut or slack alternator belt,
– an alternator fault.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS35
Engine diagnostics warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'Engine emission control sys
tem faulty' on the multifunction display.
If it flashes when the engine is running, this indicates a malfunction in the injection, ignition or emission control system. There
is a risk of damage to the catalytic converter (petrol engine onl y).
Contact a PEUGEOT dealer as soon as possible.
Bulb blown warning light
Display of this indicator light is accompanied by an audible signal and the message 'Bulb... faulty' on the multifunc
tion display, indicating the faulty bulb: a bulb in th e dipped beam lights, the side lights, the direction indi cator lights
(except side repeaters) or the brake lights (except the central brake light).
Change the faulty bulb.
Windscreen/headlamp wash reservoir warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Screenwash low'on the multi
function display.
Fill the windscreen/headlamp wash reservoir the next time you st op.
Particulate emission filter saturation warning light (diesel engine)
Display of this warning light is accompanied by an audible si gnal.
When it occurs with the engine running, this indicates the start of saturation of the particulate emission filter (excep
tionally long periods of town type driving conditions: reduce d speed, long tailbacks...).
To regenerate the filter, you are advised to drive as soon as possible and when traffic conditions permit at a speed of 35 mph
(60 km/h) or more for at least five minutes (until the warning li ght goes out).
If the light remains on, contact a PEUGEOT dealer.
Note: After prolonged operation of the vehicle at a very low speed or at idle, you may sometimes notice steam coming from
the exhaust during acceleration. This has no effect on the p erformance of the vehicle or on the environment.

INSTRUMENTS AND CONTROLS37
List of status indicator lights
SPORT suspension indicator light
Display of this indicator light is accompanied by an audible signal.
The indicator light comes on when the SPORTfunction is switched on.
Dynamic stability control (ESP/ASR) system disarming indicato r light
Display of this indicator light when the system is disarmed is acco mpanied by an audible signal and the message
'ASR/ESP systems deactivated' on the multifunction display.
Dynamic stability control (ESP) system operation indicator lig ht
This comes on when the system starts to function.
Diesel engine preheat indicator light
If the temperature is high enough, the indicator light do es not come on and you can start the engine immediately.
If the indicator light does come on, wait for it to go ou t before operating the starter.
Air bag disarming indicator light*
Display of this light is accompanied by an audible signal an d the message 'Passenger air bag disarmed' on the
multifunction display.
If the passenger air bag is disarmed, the indicator light comes on when the ignition is switched on (2nd notch).
In all cases, if the indicator light flashes, contact a PEUGEOT dealer.
*According to country

INSTRUMENTS AND CONTROLS
40
Coolant temperature indicator
When the needle is in
zone A, the
temperature is correct.
When the needle is in zone B, the
temperature is too high.
In cases where the coolant tem
perature warning light comes on
(linked to the STOPwarning light),
you must stop immediately.
Warning: wait for the engine to cool
down.
If necessary, top up the level.
Because the cooling system is pres
surised, to prevent the risk of scald
ing, turn the cap two turns to allow
the pressure to drop.
When the pressure has dropped,
remove the cap and top up the level.
Contact a PEUGEOT dealer.Engine oil level and
temperature
When the ignition is switched on, this
gauge indicates the engine oil level
for approximately 20 seconds, then it
indicates the engine oil temperature.
Engine oil level
The reading is valid only if the vehi
cle is on level ground, and the
engine has been switched off for 10
minutes.
With the ignition on, wait for the
graduated sector to light up and the
indicator needle to move.
When the needle is in zone C, the oil
level is correct.
When the needle is in zone D, the oil
level is incorrect.
There is a risk of damage to the
engine.
 Check the level with the dipstick.
You must top up the level without
exceeding the maximum level on
the gauge.
Engine oil temperature
When the needle is in zone E, the
temperature is correct.
When the needle is in zone F, the
temperature is too high.
Reduce your speed to lower the
temperature.
Service indicator and total
distance recorder
When the ignition is switched on, this
indicates servicing information for a
few seconds, then the total and trip
distances.
Service function
See the 'Service indicator' section.
Total distance recorder function
The total distance is displayed on the
left side of the screen and the trip
distance on the right side.

Trip recorder
zero reset
With the ignition on, press
the button.
Manual operation
With the headlamps on, press button
B to increase the brightness of the
instrument panel lighting or button A
to reduce it.
As soon as the lighting reaches the
required level of brightness, release
the button.
INSTRUMENTS AND CONTROLS 41
Illumination
buttons
Automatic operation
The degree of illumination of the
instrument panel automatically
adapts to the external brightness.
By day , the setting cannot be altered.
At night, the brightness can be
increased by means of button B.
A Peugeot dealer is able to cancel
automatic operation if you prefer
manual operation.

YOUR 607 IN DETAIL
52
GENERAL FUNCTIONS On/off
With the ignition key in the accessories position (1st notch) or with the ignition on (2nd notch), press button
A to switch the set on or off.
The set can operate for 30 minutes without the vehicle ign ition being switched on.
Antitheft system
The audio system is coded in such a way that it can operate on ly on your vehicle. It would not function if fitted to another
vehicle.
This system is automatic and requires no action on your part.
ADJUSTING THE SOUND Adjusting the volume
Turn buttonAto increase or decrease the volume.
Note: the automatic volume correction function "CAV", which depends on the speed of the vehicle, is acces
sible using the audio menu on the multifunction display.
AUDIO SETTINGS Press the 'AUDIO' button several times in succession to access the bass (BASS), treble (TREB), loudness
(LOUD), fader (FAD) , balance (BAL)and automatic volume correction (CAV).
Exit from audio mode is automatic after a few seconds without p ressing any button, or by pressing the
'AUDIO' button after adjusting the balance.
Note: bass and treble settings are specific to each source. It is possibl e to set them differently for radio,
cassette (RM2 audio) or CD changer.

TELEPHONE: Audio/Telephone RT2
This function is a GSM 900 MHZ telephone incorporated in the audio system.
It possesses a 'hands free'function, provided by a microphone located in the front courte sy light and a steering column
remote control which allows access to most of the functions.
It also possesses a 'confidential' function, provided by the instrument panel located in the u pper casing of the centre front
armrest.
Note: An echo may be heard for a few seconds at the beginning of t he call.
The principal "mobile"type functions are shown on the display incorporated in the a udio system; the menu lists can be
referrred to on the multifunction display.
This function is active when the ignition key is in the accessories position (1st notch), the ignition is switched on (2nd notch),
the engine is running or the vehicle is being driven.
Note: when the ignition key is in the accessories position (1st notch) or the ignition is switched on (2nd notch), this function
will be interrupted after thirty minutes, when the message 'Economy mode active'appears on the multifunction display. If
you are using the telephone at that time, you will be ab le to finish your call.
General information about the display (Audio/Telephone R T2 display)
In telephone mode, the display shows the following informa tion, where applicable.
1. Network signal indicator (3 levels).
2. Service indicator not available.
3. Indicates a communication in progress.
4. Indicator showing connection to an outside network.
5. Indicates:
– when continuously lit: presence of an unread message or message s.
– when flashing: the message tape is full.
6. Display zone (10 symbols x 2 lines).
YOUR 607 IN DETAIL
62

Selecting telephone mode / Entering a number / Switching off the microphone
To change to telephone mode, press the 'TEL' button or for more than 2 seconds on the steering column
remote control.
Insert your SIM card fully into the slot at the front (use only t he new generation 3V SIM card with bank card
format).
Note: the SIM card must not be taken out while the audio/telepho ne system is still in use. If you forget to do this, an audi
ble signal will sound for a few seconds after the ignition is switched off.
Enter your PIN number and confirm with the 'OK' button in order to access the network. The welcome screen is
displayed.
Note: the PIN code is erased each time the ignition is switched off , but the ''PIN code protection'' function may be
cancelled.
Enter the number of the person you wish to speak to on the di gital keypad and pres the 'OK'button to make the call.
To switch off the microphone midcommunication, press the 'TEL'button.
Cancelling the PIN code request
To cancel the PIN code request, select 'PIN code protection' in the 'Telephone parameters' menu and confirm; select 'OFF'
and confirm, then input your PIN code and confirm.
Receiving / Ending a call
When a ringing sounds to let you know that a call is waiti ng, you can choose either to accept it by press
ing the 'OK'button or not to accept it by pressing button Por by selecting 'Refuse call' using the steer
ing column remote control, pressing the end to confirm.
If you do not accept it, the call is diverted to your voice mai l (if this service is available and active).
To end the call, press button Por the end of the steering wheel remote control.
Note: Not accepting or ending a call by means of the steering whee l control returns the system to radio mode.
Receiving two incoming calls
During a call, when there is another incoming call, you are i nformed of this by a ring and a message. You may choose:
– to accept the call by pressing button 2 then "OK"; the first caller is put on hold and you are in contact wit h the second.
However, pressing button 2 again allows you to return to th e first caller,
– to finish the call you are on and talk to the second call er by pressing button 1 then "OK",
– not to accept the new call by pressing button "C".
YOUR 607 IN DETAIL 63

YOUR 607 IN DETAIL
74
Main menu
Switch on the ignition.
Press the 'Menu'button to access the ' Main menu'.
Select a function by turning the dial, then confirm (press
the dial). The
''Navigation/Guidance'' menu offers various possibil
ities for activating guidance:
– by inputting the address of a new destination,
– by selecting a service (hotel, station, airport...) available in a town,
– by selecting an address stored in one of the two directo ries,
– by resuming previously interrupted guidance, Two messages may be displayed, depending on the pre
vious action: 'Resume guidance' or 'Stop guidance'.
Navigation / guidance
Following selection of the 'Navigation / guidance'menu,
a screen warns you about the use of the navigation sys
tem. Please observe the instructions.
Press the dial to access the next screen.