ignition Peugeot 607 Dag 2002 Owner's Guide

THE ALARM
This provides two types of protec
tion, exterior and interior:
– exterior protection: when this is set, the alarm sounds if a door, the
boot or the bonnet is opened.
– interior protection: when this is set, the alarm sounds if the sensors
detect a variation in the air move
ment inside the vehicle (breaking
of a window or a movement inside
the vehicle).
Setting the alarm
Switch off the ignition and get out
of the vehicle.
Set the alarm within five minutes
of getting out of the vehicle, by
locking or deadlocking using the
remote control (button Bindicator
light flashes once per second). Note:
if you wish to lock your vehicle
without setting the alarm, use the
door lock.
When the alarm is triggered, the
siren sounds and the direction indi
cators flash for thirty seconds.
It then stops, but the alarm remains
set.
Warning: if the alarm has been trig
gered ten times in succession, on
the eleventh time it becomes inac
tive.
Note: if button B flashes rapidly, the
alarm has been triggered while you
were away from your vehicle.
Automatic activation
The alarm is activated automatically
two minutes after the door or boot
were last closed.
In order to avoid accidental trigger
ing of the alarm when a door or the
boot is opened, it is essential to
press the remote control opening
button first.
Disarming
Unlock the vehicle with the remote
control key (button Bindicator light
goes out).
Note: if the alarm has been triggered
while you were away from your car,
the rapid flashing of the indicator
light will stop when you switch on the
ignition. To set the alarm with exterior
protection only
If, while you are away from the vehi
cle, you wish to leave a window par
tially open or a pet inside the vehicle,
you should choose exterior protec
tion only.
Switch off the ignition
In the next ten seconds, press
button
Auntil indicator light B is
on continuously.
Get out of the vehicle.
Set the alarm by locking or dead
locking using the remote control
switch ( button Bindicator light
flashes once a second).
Note: when the alarm is set but the
remote control does not operate:
Unlock the doors with the key and
open the door. The alarm is trig
gered.
Switch on the ignition in the next
ten seconds. The alarm is disar
med.
Incorrect operation
When the ignition is switched on, if
button Blights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
YOUR 607 IN DETAIL
104

Child safety
This prevents either of the rear doors
being opened from inside. Turn the red plastic switch a quar
ter of a turn using the ignition key.
YOUR 607 IN DETAIL 105
DOORS
Opening the doors
from outside
Opening the doors
from insideLocking / unlocking from the
inside
– Using button
Aof the centre con
sole :
This allows the doors, the boot and
the fuel filler flap to be locked or
unlocked.
– Using button B on the door :
• on the front doors this allows the doors, the boot and the fuel filler
flap to be locked or unlocked.
• on the rear doors this allows the door concerned to be locked or
unlocked.
Note : button Bis neutralised if the
vehicle is deadlocked.
' Door open' alert
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, if a door is not proper
ly closed then the door open warning
light comes on, accompanied by an
audible signal and a diagram indicat
ing the relevant door on the
multi–function display, if a door is not
properlyclosed.

Vehicle unlocked
 Press and hold button Cof the
remote control key or press push
button A.
Note: pushbutton Acan be deacti
vated. Rotate control B,located
inside the boot lid, a quarter of a turn
(anticlockwise) using the key.
YOUR 607 IN DETAIL
106
THE BOOT
Opening the boot
With the vehicle locked / deadlocked

Press and hold button Cof the
remote control key.
This action will also unlock the doors
and the fuel filler flap. SUNROOF
Control the sunroof:
– manually
: lightly press the switch;
the roof stops as soon as the
switch is released.
– automatically : press the switch
down; the roof opens partially or
opens or closes completely
depending on where the switch is
pressed.
– to partially open the roof: press
part Aof the switch. To close it,
press part Bof the switch.
– to open the roof completely: press part Bof the switch.
– to close it completely: press part
A of the switch .
– safety autoreverse When the sunroof is closing and
meets an obstacle, it stops then
opens again.
Note: the sunroof shutter is manual.
Closing the boot
 Press the centre of the boot lid
with both hands, until it locks.
'Boot open' warning
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, the door open warning
light comes on, accompanied by an
audible signal and a diagram on the
multifunction display, if the boot is
not properly closed.

The engine and the ignition must
be switched off when filling with
fuel : Open the fuel filler flap by press
ing its front right hand edge,
 Unscrew the cap and hook it over
the tab located on the inside of the
flap.
When filling up your tank, do not con
tinue after the 3rd cutoff of the
pump; this could cause your vehicle
to malfunction.
The capacity of the tank is approx
imately 80 litres.  After filling the tank, screw the cap
on fully and close the flap.
Fuel filler cap open When this light comes on,
accompanied by an audible
signal and the message
'Fuel cap open' on the dis
play, screw the cap on again
and close the fuel filler flap.
YOUR 607 IN DETAIL 107
BONNET
Opening
 Pull the lever, located in the dri
ver's footwell, downwards.
 Lift the catch and raise the bon
net.
Bonnet assister struts open the bon
net and keep it open.
Closing
 Lower the bonnet and release it at
the end of its travel.
 Check that it is locked.
'Bonnet open' warning
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, the door open warning
light comes on, accompanied by an
audible signal and a diagram on the
multi–function display, if the bonnet
is not properly closed. FILLING WITH FUEL
Low fuel level
When the minimum fuel
level is reached, this warn
ing light comes on, accom
panied by an audible signal
and the message 'Fuel
level low' on the multifunction dis
play.
You can can still drive approxi
mately 30 miles (50 km) without
filling up with fuel.
Filling with fuel
Locking and unlocking of the fuel
filler flap, the doors and the boot is
simultaneous (except when selective
unlocking is initialised; in this case
press the unlocking button of the
remote control again).

108
YOUR 607 IN DETAIL
LIGHTS STALK
Front and rear lights (ring A) Turn ring Ato the position
required.
Lights off
Side lightsDipped / main beam
headlamps Dipped / main
beam change
 Pull the stalk fully towards you.
Note : with the ignition and the auto
matic lights function switched off, on
opening the driver's door a buzzer
sounds if you have left your lights on.
Front and rear fog lamps (ring B)
 Turn ring Bto the position
required. The position is con
firmed by the light on the instru
ment panel.
Front fog
lamps
These operate with the side lights and
the dipped / main beam headlamps.
Neutral
position.
Rear fog lamps
These operate with the side lights
and the front fog lamps, or the
dipped / main beam headlamps. Direction indicators
(flashers)
Left : downwards.
Right : upwards
Note : If you forget to return the
direction indicator to its normal posi
tion, the volume of the audible signal
will increase, if you are driving at a
speed greater than 40 mph
(60 km/h).
Parking lights
The parking lights are lit on the side
the traffic is on.
With the engine switched off, place
the indicator lights stalk on the traffic
side (i.e. for parking on the right;
switching on of the lights on the left).

Operating check
ActivationWhen this function is acti
vated, the indicator light
comes on, accompanied by
an audible signal.
The light also comes on as soon as
the driver changes the stalk position
to 0.
Neutralisation When neutralising the func
tion, the indicator light
comes on, accompanied by
an audible signal.
The indicator light also comes on as
soon as the driver uses the manual
lighting controls.
If the sunshine / brightness sen
sor does not function correctly,
the system activates the function
(the lights come on) and the dipped
beam headlamps indicator light on
the instrument panel flashes.
Contact a PEUGEOT dealer to have
the system checked.
109
Automatic switching
on of the lights
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off as soon as the light
becomes bright enough or the wind
screen wipers stop.
Note : in foggy weather, the bright
ness sensor can detect sufficient
light. As a consequence, the lights
will not come on automatically.
This function is active when the vehi
cle is supplied to the customer.
To switch the function on or off::
Place the key in the accessories
position (1st notch),
Change the stalk position to 0,
Press the end of the stalk for more
than two seconds.
Note : after the ignition is switched
off and depending on the brightness,
the lights remain on for approximate
ly thirty seconds or until the vehicle is
locked. Do not cover the sunshine /
brightness sensor located in the
centre of the fascia. It helps to
regulate the air conditioning,
automatic switching on of the
lights and the automatic adjust
ment of the instrument panel
brightnes.
YOUR 607 IN DETAIL

110
Screenwash/headlamp wash lowWhen the minimum level of
the reservoir is reached,
this warning light comes on,
accompanied by an audible
signal and the message
'Screenwash low' on the multi
function display.
Next time you stop, fill the screen
wash / headlamp wash reservoir.
If the reservoir is empty, the warning
light comes on when the ignition is
switched on, or every time the stalk
is operated, until the reservoir is
filled.
YOUR 607 IN DETAIL
WINDSCREEN
WIPER STALK
Windscreen wipers
3 Fast wipe
2 Normal wipe
1 Intermittent or automatic wipe
0 Off
When the ignition has been
switched off for more than a
minute with the control in a wipe
position (1, 2 or 3), it is necesary
to reactivate this function. To d o
this, move the stalk to any position,
then move it back to the required
position. Windscreen and headlamp wash
Pull the windscreen wiper stalk
towards you.
The windscreen wash then the wind
screen wipers operate for a fixed
period. The windscreen wash and
headlamp wash operate simultane
ously for a few seconds,
only if the
dipped beam or main beam head
lamps are on. Do not cover the rain
sensor located on the
windscreen behind the
interior mirror.
When using an automat
ic car wash, switch off the ignition
or check that the wiper stalk is not
in the automatic position.
In winter, it is advisable to wait
until the windscreen is completely
free of ice before operating the
automatic wipe.
Maintenance position
This position enables the wiper
blade to be removed.
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen so that they may be
cleaned or replaced.
To park the wipers after this has
been done, switch on the ignition
and operate the stalk.

113
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
Note: this figure may rise if there is a
change in driving style or road sur
face, causing a significant drop in
current fuel consumption. Average consumption
This is the average fuel consumption
since the computer was last set to
zero.Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
YOUR 607 IN DETAIL
Current consumption
This is the average fuel consumption
during the last few seconds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average speed
this is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The routes
Routes 1 and 2 are independent but
have identical application.
Route 1, for example, allows you
to make daily calculations, and route
2 monthly calculations.
On this page, the illustration on
the left represents the mono
chrome screen C display, the one
on the right the colour screen
display.
After resetting the trip computer to
zero, the range data become signif
icant only after a few seconds of
use.
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.

YOUR 607 IN DETAIL
116
EXTERIOR MIRRORS
Adjustment from the inside Turn knob Bto the right or to the
left to select the corresponding
mirror.
 Move knob Bin all four directions
to adjust.
Folding back the mirrors electri
cally *  With the ignition on, turn knob Bto
position A.
or,
 Lock the vehicle using the remote
control.
Note: this function can be neu
tralised. Contact your PEUGEOT
dealer.
When the vehicle is parked, the
exterior mirrors can be folded
back manually. Automatically adjustable
mirrors for parking
These allow you to see the ground
(kerb, wall...) when carrying out
parking manoeuvres in reverse gear.
Tilting the mirror to the parking posi
tion:
 switch on the direction indicator
on the parking side,
 engage reverse gear.
The exterior mirror corresponding
to the side on which you are park
ing tilts downwards.
Returning the mirror to the previous
position:  change out of reverse gear.
Note: to be active, this function must
be initialised by adjusting the mirror,
with reverse gear engaged and the
direction indicator on the side of the
mirror to be adjusted switched on.
Each remote control can memorise a
specific setting.
The driver's mirror is con
vex in order to eliminate
the 'blind spot' (area at
edge defined by a dotted
line).
As a result, objects observed in
the driver's and passenger's mir
rors are in reality closer than they
appear.
This must be taken into account to
judge correctly the distance of
vehicles approaching from
behind.

YOUR 607 IN DETAIL117
Automatic day/night interior mirror
This automatically and gradually changes between the day and
night positions.
To prevent dazzling, the glass of the mirror darkens automatically depending on
the intensity of the light from behind. It clears as the li ght (headlamps of follow
ing vehicles, sunlight) decreases, ensuring maximum visibility.
Operation
Switch on the ignition and press switch 1:
– Indicator light 2lit (switch pressed): automatic operation.
– Indicator light 2off: automatic system off. The mirror remains at its most clear.
Special feature
To ensure maximum visibility during manoeuvres, the mirror clears automatical
ly when reverse gear is engaged. Interior mirror
The interior mirror has two positions:
–
day (normal),
– night (antidazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
Areas for toll cards /
car park tickets
The athermic windscreen has two
nonreflective zones located either
side of the base of the interior
mirror.
They are intended for affixing toll
cards and/or car park tickets.