steering Peugeot 607 Dag 2002 Owner's Manual

3YOUR AT A GLANCE
1Lights and direction indica
tors stalk.
2 Steering wheel adjustment.
3 Driver's front air bag.
Horn.
4 Instrument dials.
5 Windscreen wash/wipe
stalk.
Trip computer stalk.
6 Audio remote control stalk.
7 Hazard warning lights
switch.
8 Central adjustable
heating/ventilation vents and
air flow regulation.
9 Sunshine / brightness
sensor.
10 Windscreen demisting
vents.
11 Passenger air bag.
12 Glove compartment.
13 Side adjustable heating/ven
tilation vents and air flow
regulation. 14
Door window demisting
vent.
15 Passenger air bag disarming
switch.
16 Front seats heating switch.
17 Rear ashtray.
Rear lighter.
Rear seats heating switch.
18 Rear footwell heating vent.
19 Twoposition armrest with
compartments.
20 Handbrake.
21 Electronically controlled sus
pension switch.
Doors and boot locking
switch.
Sunroof switch.
Rear blind switch.
22 Front ashtray.
Front lighter.
23 Gear lever.
24 RM2 audio system or RT2
audio/telephone system with
PEUGEOT call button. 25
Heating/ventilation controls.
26 Multifunction display.
27 Steering lock and ignition.
28 Fuse box.
29 Speakers location.
30 Electric mirror controls.
Window controls.
Rear window locking control.
31 Headlamp height adjust
ment.
32 ESP disarming switch.
33 Alarm button.
34 Cruise control.
35 Memory buttons for:
Front seat settings
Electric mirror settings

YOUR AT A GLANCE5
STARTING
STOP position:
The ignition is switched off.
1st notch, Accessories position:The ignition is switched off but
the accessories still function.
2nd notch, Running position:
The ignition is on.
Starting position:
Operates the starter.
Starting a diesel engineIf the temperature is highenough, the preheat
indicator light does not
come on and you can
start immediately.
If the indicator light comes on,
wait for it to go out before operat
ing the starter.
If the engine stalls, it is neces
sary to return the key to the
'Stop' position before restarting. CHECK
(vehicle autotest)
Automatic check
With the ignition on (2nd notch)
If no malfunction has been
detected: In the absence of
vehicle function status indi
cator lights, the OK light is
displayed after two seconds
on the instrument panel screen.
Otherwise, it will be displayed after
these indicator lights come on.
If a 'minor' malfunction has been
detected: the warning light for the
faulty function is displayed on the
instrument panel screen. Certain
indicator lights showing the status of
vehicle functions may also come on,
followed by the OKindicator light.
If a 'major' malfunction has been
detected: the corresponding warn
ing light is displayed on the instru
ment panel screen. Certain indicator
lights showing the status of vehicle
functions may also come on. The
OK indicator light does not come
on. Do not start your vehicle.
Contact a PEUGEOT dealer.
Afterwards, if the passenger air
bag is disarmed, the correspond
ing warning light will come on.
With the engine running or if the
vehicle is moving, the instrument
panel screen temporarily displays:
– lights indicating warnings, when
these occur,
– vehicle function sta tus indicator lights,
when a change
occurs.
The display of certain indicator
lights is accompanied by an audi
ble signal and a message on the
multifunction display.
MANUAL CHECK  Press the "CHECK" button on the
instrument panel.
With the ignition key in the accessories
position, with the ignition switched on,
with the engine running or the vehicle
moving, this function informs you at all
times of the following:
– any current warnings,
– the status of functions which it is possible to switch on or switch off
(windscreen wipers, automatic
switching on of lights, cruise con
trol, disarming of passenger air
bag, etc.).
The corresponding warning lights are
displayed in succession on the instru
ment panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator light(s) will be
displayed at the end of this mode.
Never run the engine in
a confined space.
Do not make any modi fications to the steering
lock.
31

YOUR AT A GLANCE6
STEERING WHEEL
STALKS
LIGHTS
Front and rear lights (ring A)Lights off.
Side lights.Dipped / main
beam headlamps. Front and rear fog lamps
(ring B)
Front fog lamps.Neutral position of the
ring.
Rear fog lamps.
Parking lights
To switch on the parking lights on
the traffic side, with the engine
off, place the direction indicator
lights stalk on the traffic side.
Automatic switching on of lights
This occurs if the light is poor, as well as in cases of contin uous operation
of the windscreen wipers, and stops as soon as the light has b ecome
bright enough or the windscreen wipers have stopped.
 To activate or disarm the function, place the key in the accessori es
position (1st notch), place the lights stalk in position 0and press the
end of the stalk for more than two seconds.
Do not cover the sunshine / brightness sensor located i n
the centre of the fascia. It helps to regulate the air condi
tioning, the automatic switching on of the lights and the
automatic adjustment of the instrument panel bright
ness. WINDSCREEN WIPERS
3
Rapid wipe
2 Normal wipe
1 Automatic wipe
0 Off
Automatic wipe
In position 1, the wipers operate
automatically and adjust their
speed to the intensity of the rain
fall.
When the ignition has been
switched off for more than one
minute with the control in a
wipe position, it is necessary
to reactivate this function.
To do this, move the control to
any position, then return to the
required position.
10811 0

YOUR AT A GLANCE7
ELECTRIC WINDOWS
1 Driver's electric window.
2 Passenger's electric window.
3 Rear right electric window.
4 Rear left electric window.
5 Disarming the rear window controls.
Manual mode: Press or pull the switch lightly. The window stops as soon as th e switch
is released.
Automatic mode: Press or pull the switch firmly. One touch completely opens or close s
the window.
Safety autoreverse: when the glass rises and meets an
obstacle, it stops and lowers again.
ELECTRIC REAR VIEW MIRRORS  Turn knob 6to the right or to the left to select the corre
sponding mirror.
 Move the knob in all four directions to adjust.
When parked, the mirrors can be folded back manually, electrically by
means of button 6or automatically on locking the vehicle. STEERING WHEEL
HEIGHT AND DEPTH
ADJUSTMENT 
Pull handle Adownwards to
unlock the steering wheel.
 Adjust the height and depth of
the steering wheel.
 Lock by pushing handle Afully
upwards.
11 5
11 611 8

YOUR AT A GLANCE9
REAR PARKING
ASSISTANCE
This system, installed in the rear
bumper, detects any obstacle (per
son, vehicle, tree, gate, kerb...)
located behind the vehicle.
To activate
With the engine running, the sys
tem is activated as soon as
reverse gear is engaged; a bleep
sounds to inform you that it is
active.
The proximity information is
given by an audible signal, con
sisting of bleeps which become
more and more rapid as the vehi
cle approaches the obstacle.
When the distance between the
rear of the vehicle and the obsta
cle is less than approximately
twentyfive centimetres, the
signal becomes con
tinuous.The system ceas
es to be active
when you change
to neutral. TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warn
ing if there is a malfunction (speed
greater than 15 mph (25 km/h).
Tyre underinflation
When this warning light
comes on, accompanied
by a bleep and the mes
sage 'Tyre(s) pressure
low', have the tyre pressure
checked as soon as possible.
Puncture
Display of this warning
light, accompanied by an
audible signal and the
message 'Punctured
tyre(s) detected', is followed by
illumination of the STOPwarning
light.
Stop immediately, avoiding all
abrupt manoeuvres with the
steering wheel and the brakes.
Change the damaged (punctured
or very underinflated) wheel and
have the tyre pressure checked
as soon as possible.
Note: if the damaged wheel is
stored temporarily in the boot, it
will again send this message as a
reminder of the necessity of hav
ing it repaired. This will prevent a
similar warning being displayed. Sensor(s) not detected
Display of this warning
light, accompanied by an
audible signal and the
message 'X tyre pres
sure sensor(s) missing', indi
cates that one or more wheels
are not being detected.
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Warning: this message is dis
played when one of the wheels is
at a distance from the vehicle
(being repaired) or when a wheel
without a sensor is fitted (winter
fitting).
This system does not eliminate
the need to check the tyre
pressure regularly.
128139

PEUGEOT SERVICING 25
Level
Operations Description of operation 1st service
A C Intermediate
DRAIN/REFILL Engine oil Bleed fuel filter (diesel) Oil filter Fuel filter
*(petrol)REPLACE Fuel filter element (diesel) Air filter element Spark plugs (petrol) Engine oil (check + topup) Manual gearbox oil (check + topup) Battery (check + topup) if cap is removableLEVEL Screen wash (check + topup) Coolant (check + topup) Brake fluid (check + topup) Power steering fluid (check + top up according to specification ) Operation of lights and indicators Condition of glass, headlamp and light lenses and mirrors Horn Windscreen washer jets Condition of wiper blades Condition and tension of the ancillary drive belts Handbrake Condition of hydraulic circuits (hoses and covers)CHECK Condition of rubber boots and gaiters Brake pads o Play in hubs, link rods, ball joints, flexible mountings Shock absorbers Rear drum brake lining wear Condition and pressure of tyres (including spare wheel) Emission control check as per current legislation (petrol) Smoke opacity (diesel) Pollen filter (according to specification)o
Visual check of the whole vehicle


: All driving conditions o: Arduous conditions * According to destination
SERVICE
ROAD TEST
A AND C SERVICE LEVELS AND THE INTERMEDIATE VISIT
Courtesy vehicle

27
Recommendation for
approved lubricants
The oils which appear in the table
opposite are suitable for most pur
poses.
The diagram opposite states the
optimum range of viscosity depend
ing on the temperatures at which the
oils are to be used.
It is also possible to use synthetic
oils of 'superior quality'.
In the absence of semisynthetic or
synthetic oils, oils of API SH/SJ qual
ity (for petrol engines) or CD/CF
quality (for diesel engines) can be
used by following the 'Arduous con
ditions' servicing schedule, which
specifies shorter intervals.
Do not hesitate to ask for advice
from a PEUGEOT dealer to maintain
driving pleasure and to minimise the
maintenance cost of your vehicle.
For countries outside Europe, please
contact a local PEUGEOT dealer.
TOTAL
ONLY ONLY
Manual ESSO GEAR OIL BV TOTAL TRANSMISSION BV
gearbox 75W 80 Part no. 9736.41 75W 80
Automatic ONLY
gearbox ATF 4HP20AL4
4HP20 Part no. 9736.22
Power steering ESSO ATF D TOTAL FLUIDE AT42 Part no. 9730.94
Power steering FLUIDE DA Part no. 9730. A1*
Brake fluid PEUGEOT DOT 4
Coolant PROCORTM108/GLYSANTIN G33 or REVKOGEL 2000 ONLY.Protection to 35°C
*Only in very cold climates. Other approved products
PEUGEOT SERVICING

TELEPHONE: Audio/Telephone RT2
This function is a GSM 900 MHZ telephone incorporated in the audio system.
It possesses a 'hands free'function, provided by a microphone located in the front courte sy light and a steering column
remote control which allows access to most of the functions.
It also possesses a 'confidential' function, provided by the instrument panel located in the u pper casing of the centre front
armrest.
Note: An echo may be heard for a few seconds at the beginning of t he call.
The principal "mobile"type functions are shown on the display incorporated in the a udio system; the menu lists can be
referrred to on the multifunction display.
This function is active when the ignition key is in the accessories position (1st notch), the ignition is switched on (2nd notch),
the engine is running or the vehicle is being driven.
Note: when the ignition key is in the accessories position (1st notch) or the ignition is switched on (2nd notch), this function
will be interrupted after thirty minutes, when the message 'Economy mode active'appears on the multifunction display. If
you are using the telephone at that time, you will be ab le to finish your call.
General information about the display (Audio/Telephone R T2 display)
In telephone mode, the display shows the following informa tion, where applicable.
1. Network signal indicator (3 levels).
2. Service indicator not available.
3. Indicates a communication in progress.
4. Indicator showing connection to an outside network.
5. Indicates:
– when continuously lit: presence of an unread message or message s.
– when flashing: the message tape is full.
6. Display zone (10 symbols x 2 lines).
YOUR 607 IN DETAIL
62

Selecting telephone mode / Entering a number / Switching off the microphone
To change to telephone mode, press the 'TEL' button or for more than 2 seconds on the steering column
remote control.
Insert your SIM card fully into the slot at the front (use only t he new generation 3V SIM card with bank card
format).
Note: the SIM card must not be taken out while the audio/telepho ne system is still in use. If you forget to do this, an audi
ble signal will sound for a few seconds after the ignition is switched off.
Enter your PIN number and confirm with the 'OK' button in order to access the network. The welcome screen is
displayed.
Note: the PIN code is erased each time the ignition is switched off , but the ''PIN code protection'' function may be
cancelled.
Enter the number of the person you wish to speak to on the di gital keypad and pres the 'OK'button to make the call.
To switch off the microphone midcommunication, press the 'TEL'button.
Cancelling the PIN code request
To cancel the PIN code request, select 'PIN code protection' in the 'Telephone parameters' menu and confirm; select 'OFF'
and confirm, then input your PIN code and confirm.
Receiving / Ending a call
When a ringing sounds to let you know that a call is waiti ng, you can choose either to accept it by press
ing the 'OK'button or not to accept it by pressing button Por by selecting 'Refuse call' using the steer
ing column remote control, pressing the end to confirm.
If you do not accept it, the call is diverted to your voice mai l (if this service is available and active).
To end the call, press button Por the end of the steering wheel remote control.
Note: Not accepting or ending a call by means of the steering whee l control returns the system to radio mode.
Receiving two incoming calls
During a call, when there is another incoming call, you are i nformed of this by a ring and a message. You may choose:
– to accept the call by pressing button 2 then "OK"; the first caller is put on hold and you are in contact wit h the second.
However, pressing button 2 again allows you to return to th e first caller,
– to finish the call you are on and talk to the second call er by pressing button 1 then "OK",
– not to accept the new call by pressing button "C".
YOUR 607 IN DETAIL 63

Services
This menu gives direct access.
Press button O to display the "Services" menu and make a selection from the following three menus, the n validate by press
ing the end of the steering wheel remote control:
– ''Emergency call''* to automatically send a call containing a minimessage (SMS) which a llows you to be identified and
located; vocal communication is established with the help cent re,
– ''Technical assistance''* for contacting the call centre controlling the PEUGEOT breakdown service,
– ''Peugeot Service"* to contact directly the PEUGEOT customer contact centre and access the services offered.
IMPORTANT: as is the case for all telephones, your onboard telephone op erates using cellular and terrestrial networks.
Because of this, connection cannot be guaranteed in all cases.
Selecting a directory
To consult the various directories, insert your SIM card and input t he PIN code.
To access the 'Directories' menu, press the 'MAN'button or press the end of the steering wheel remote
control.
Make a selection from the three directories available: DIRECTORY (SIM), LAST NUMBERS CALLEDor TEL (PEUGEOT
customer contact centre).
Storing numbers
Last numbers called: your phone stores in the memory the five last numbers called or whi ch were used to call you.
To access these numbers, press the 'OK' button or the end of the steering column remote control and scroll
through these numbers using buttons Mand Lor the knob of the steering column remote control. Then, if
you want to call one of these numbers, press the 'OK' button, or the end of the steering column remote con
trol.
Telephone directory (SIM): this can store around eighty numbers (if more than 80 numbers are st ored on the SIM card
used, only the first 80 will be accessible).
YOUR 607 IN DETAIL 65
* If option and service available.