turn signal Peugeot 607 Dag 2002 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2002, Model line: 607 Dag, Model: Peugeot 607 Dag 2002Pages: 167, PDF Size: 2.61 MB
Page 4 of 167
YOUR AT A GLANCE5
STARTING
STOP position:
The ignition is switched off.
1st notch, Accessories position:The ignition is switched off but
the accessories still function.
2nd notch, Running position:
The ignition is on.
Starting position:
Operates the starter.
Starting a diesel engineIf the temperature is highenough, the pre heat
indicator light does not
come on and you can
start immediately.
If the indicator light comes on,
wait for it to go out before operat
ing the starter.
If the engine stalls, it is neces
sary to return the key to the
'Stop' position before re starting. CHECK
(vehicle autotest)
Automatic check
With the ignition on (2nd notch)
If no malfunction has been
detected: In the absence of
vehicle function status indi
cator lights, the OK light is
displayed after two seconds
on the instrument panel screen.
Otherwise, it will be displayed after
these indicator lights come on.
If a 'minor' malfunction has been
detected: the warning light for the
faulty function is displayed on the
instrument panel screen. Certain
indicator lights showing the status of
vehicle functions may also come on,
followed by the OKindicator light.
If a 'major' malfunction has been
detected: the corresponding warn
ing light is displayed on the instru
ment panel screen. Certain indicator
lights showing the status of vehicle
functions may also come on. The
OK indicator light does not come
on. Do not start your vehicle.
Contact a PEUGEOT dealer.
Afterwards, if the passenger air
bag is disarmed, the correspond
ing warning light will come on.
With the engine running or if the
vehicle is moving, the instrument
panel screen temporarily displays:
– lights indicating warnings, when
these occur,
– vehicle function sta tus indicator lights,
when a change
occurs.
The display of certain indicator
lights is accompanied by an audi
ble signal and a message on the
multi function display.
MANUAL CHECK Press the "CHECK" button on the
instrument panel.
With the ignition key in the accessories
position, with the ignition switched on,
with the engine running or the vehicle
moving, this function informs you at all
times of the following:
– any current warnings,
– the status of functions which it is possible to switch on or switch off
(windscreen wipers, automatic
switching on of lights, cruise con
trol, disarming of passenger air
bag, etc.).
The corresponding warning lights are
displayed in succession on the instru
ment panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator light(s) will be
displayed at the end of this mode.
Never run the engine in
a confined space.
Do not make any modi fications to the steering
lock.
31
Page 7 of 167
CRUISE CONTROL
Cruise control enables the vehi
cle to maintain a steady speed
programmed by the driver, with
out the accelerator being
pressed.
In order for it to be memorised,
the speed of the vehicle must be
greater than 25mph (40km/h) or
40mph (60km/h) depending on
engine.
OperationPlace the ring of stalk
A in the ONposition. The
indicator light comes on,
accompanied by an audi
ble signal. FRONT AIR BAGS
Disarming the passenger air
bag*
with the ignition off, insert the
key into slot
1and turn it:
–to the 'ON'position, the pas
senger air bag is armed,
–to the 'OFF'position, the pas
senger air bag is disarmed.
Operating check When the passenger air
bag is disarmed, the
warning light comes on
when the ignition is
switched on (2nd notch),
accompanied by an audible sig
nal and the message 'Passenger
air bag disarmed' . Front air bag faulty
If this warning light
comes on, accompanied
by an audible signal and
the message 'Air bag
faulty' , contact a PEUGEOT
dealer to have the system
checked.
Passenger air bag
precautions
Disarm the
air bag if you
install a rear
facing child
seat. Arm the air
bag for an
adult passen
ger.
Never place your feet or any
object on the fascia.
* According to country
YOUR AT A GLANCE11
127129
Page 62 of 167
Selecting telephone mode / Entering a number / Switching off the microphone
To change to telephone mode, press the 'TEL' button or for more than 2 seconds on the steering column
remote control.
Insert your SIM card fully into the slot at the front (use only t he new generation 3V SIM card with bank card
format).
Note: the SIM card must not be taken out while the audio/telepho ne system is still in use. If you forget to do this, an audi
ble signal will sound for a few seconds after the ignition is switched off.
Enter your PIN number and confirm with the 'OK' button in order to access the network. The welcome screen is
displayed.
Note: the PIN code is erased each time the ignition is switched off , but the ''PIN code protection'' function may be
cancelled.
Enter the number of the person you wish to speak to on the di gital keypad and pres the 'OK'button to make the call.
To switch off the microphone mid communication, press the 'TEL'button.
Cancelling the PIN code request
To cancel the PIN code request, select 'PIN code protection' in the 'Telephone parameters' menu and confirm; select 'OFF'
and confirm, then input your PIN code and confirm.
Receiving / Ending a call
When a ringing sounds to let you know that a call is waiti ng, you can choose either to accept it by press
ing the 'OK'button or not to accept it by pressing button Por by selecting 'Refuse call' using the steer
ing column remote control, pressing the end to confirm.
If you do not accept it, the call is diverted to your voice mai l (if this service is available and active).
To end the call, press button Por the end of the steering wheel remote control.
Note: Not accepting or ending a call by means of the steering whee l control returns the system to radio mode.
Receiving two incoming calls
During a call, when there is another incoming call, you are i nformed of this by a ring and a message. You may choose:
– to accept the call by pressing button 2 then "OK"; the first caller is put on hold and you are in contact wit h the second.
However, pressing button 2 again allows you to return to th e first caller,
– to finish the call you are on and talk to the second call er by pressing button 1 then "OK",
– not to accept the new call by pressing button "C".
YOUR 607 IN DETAIL 63
Page 107 of 167
Child safety
This prevents either of the rear doors
being opened from inside. Turn the red plastic switch a quar
ter of a turn using the ignition key.
YOUR 607 IN DETAIL 105
DOORS
Opening the doors
from outside
Opening the doors
from insideLocking / unlocking from the
inside
– Using button
Aof the centre con
sole :
This allows the doors, the boot and
the fuel filler flap to be locked or
unlocked.
– Using button B on the door :
• on the front doors this allows the doors, the boot and the fuel filler
flap to be locked or unlocked.
• on the rear doors this allows the door concerned to be locked or
unlocked.
Note : button Bis neutralised if the
vehicle is deadlocked.
' Door open' alert
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, if a door is not proper
ly closed then the door open warning
light comes on, accompanied by an
audible signal and a diagram indicat
ing the relevant door on the
multi–function display, if a door is not
properlyclosed.
Page 108 of 167
Vehicle unlocked
Press and hold button Cof the
remote control key or press push
button A.
Note: push button Acan be deacti
vated. Rotate control B,located
inside the boot lid, a quarter of a turn
(anti clockwise) using the key.
YOUR 607 IN DETAIL
106
THE BOOT
Opening the boot
With the vehicle locked / deadlocked
Press and hold button Cof the
remote control key.
This action will also unlock the doors
and the fuel filler flap. SUNROOF
Control the sunroof:
– manually
: lightly press the switch;
the roof stops as soon as the
switch is released.
– automatically : press the switch
down; the roof opens partially or
opens or closes completely
depending on where the switch is
pressed.
– to partially open the roof: press
part Aof the switch. To close it,
press part Bof the switch.
– to open the roof completely: press part Bof the switch.
– to close it completely: press part
A of the switch .
– safety auto reverse When the sunroof is closing and
meets an obstacle, it stops then
opens again.
Note: the sunroof shutter is manual.
Closing the boot
Press the centre of the boot lid
with both hands, until it locks.
'Boot open' warning
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, the door open warning
light comes on, accompanied by an
audible signal and a diagram on the
multi function display, if the boot is
not properly closed.
Page 110 of 167
108
YOUR 607 IN DETAIL
LIGHTS STALK
Front and rear lights (ring A) Turn ring Ato the position
required.
Lights off
Side lightsDipped / main beam
headlamps Dipped / main
beam change
Pull the stalk fully towards you.
Note : with the ignition and the auto
matic lights function switched off, on
opening the driver's door a buzzer
sounds if you have left your lights on.
Front and rear fog lamps (ring B)
Turn ring Bto the position
required. The position is con
firmed by the light on the instru
ment panel.
Front fog
lamps
These operate with the side lights and
the dipped / main beam headlamps.
Neutral
position.
Rear fog lamps
These operate with the side lights
and the front fog lamps, or the
dipped / main beam headlamps. Direction indicators
(flashers)
Left : downwards.
Right : upwards
Note : If you forget to return the
direction indicator to its normal posi
tion, the volume of the audible signal
will increase, if you are driving at a
speed greater than 40 mph
(60 km/h).
Parking lights
The parking lights are lit on the side
the traffic is on.
With the engine switched off, place
the indicator lights stalk on the traffic
side (i.e. for parking on the right;
switching on of the lights on the left).
Page 125 of 167
Notes
It is only possible to change from one gear
to another if the vehicle speed and engine
speed permit. If they do not, the vehicle will
operate temporarily in automatic mode.
When the vehicle is stationary or moving
very slowly, the gearbox automatically
selects gear M1.
Programmes S(sport) and
(snow) do not
operate in manual mode.
Operating abnormality
Any operating abnormality is
shown by illumination of this warn
ing light, accompanied by an audi
ble signal and the message 'Auto
matic gearbox faulty' on the
multi function display.
In this situation the gearbox operates in
downgrade mode (locked in 3rd gear). You
may feel a substantial knock when selecting
reverse from Pto Rand from Nto R(this will
not cause any damage to the gearbox).
Do not exceed 60 mph (100 km/h).
Contact a PEUGEOT dealer as soon as
possible.
If the battery is flat and the
lever is in position P, it will
be impossible to change
to another position.
YOUR 607 IN DETAIL 123
Automatic operation
Automatic changing of the
four gears:
select function Din the gate.
The gearbox always selects the most
suitable gear according to the follow
ing parameters:
– the style of driving,
– the road profile,
– the vehicle load.
The gearbox is then operating in auto
adaptive mode, without any action on
your part.
WARNING
Never select function N when the vehi
cle is moving.
Never select functions Por Runless
the vehicle is stationary.
Never change betwen functions to
optimise braking on a slippery surface.
Notes
For immediate maximum acceleration
without touching the gear lever, press
the accelerator pedal down as far as it
will go (kickdown). The gearbox will
automatically change down or main
tain the gear selected until maximum
engine speed is reached.
When the brake is applied, the gear
box will automatically change down in
order to provide efficient engine brak
ing.
If you take your foot off the accelerator
suddenly, the gearbox will not change
to a higher gear for reasons of safety. Sport and snow programmes
In addition to the auto adaptive pro
gramme, there are two special pro
grammes.
The programme is displayed on the
instrument panel screen.
Sport programme
Press button
Sonce the vehicle has
been started and function Dselected.
The gearbox automatically favours
sporty driving and more dynamic
acceleration.
Snow programme
This programme improves starting
and drive when traction is poor.
Press button once the vehicle has
been started and function Dselected.
The gearbox adapts to driving on slip
pery roads.
Note: you can return to the auto adap
tive programme at any time.
Press button Sor again to switch
off the programme you are in.
Manual operation
Manual changing of the four gears:
select function Min the gate,
push the lever to the + sign to
change to a higher gear,
pull the lever to the sign to change
to a lower gear.
You can change from position D(dri
ving in automatic mode) to position M
(driving in manual mode) at any time.
Page 127 of 167
YOUR 607 IN DETAIL
126
ELECTRONICALLY
CONTROLLED SUSPENSION
T
he suspension adapts automatically
and instantly to different driving styles
and road characteristics, improving the
comfort of the occupants and the vehi
cle's road holding capabilities.
The suspension favours smooth shock
absorption, ensuring a comfortable ride,
but as soon as conditions demand a
change (sporty driving, tight bends,
avoidance action, etc.) it automatically
selects firmer shock absorption, guaran
teeing optimum road holding.
Selecting the SPORT position
Press switch 1, the SPORT indi
cator light will come on,
accompanied by an audible
signal.
In this position, the suspen
sion is maintained in the
SPORT position.
To return to automatic
operation
Press switch 1again. The indicator
light will go out and the
AUTO indicator light comes
on, accompanied by an audi
ble signal.
Operating check
This is confirmed by the switch light
and the indicator lights. The switch
light comes on for approximately three
seconds every time the ignition is
switched on.
If the switch light flashes or if the indi
cator light comes on, accompanied by
an audible signal and the message
' Hydraulic suspension pressure
insufficient' , contact your PEUGEOT
dealer.
Handbrake
Locking
When parking, pull the handbrake to
immobilise your vehicle.
Warning: when parking on a slope,
direct your wheels towards the pave
ment and pull on the handbrake.
Unlocking
Pull the handle and press the button
to release the handbrake.
Page 129 of 167
YOUR 607 IN DETAIL
127
CRUISE CONTROL
Cruise control enables the vehicle to
maintain a steady speed programmed
by the driver, regardless of the road
characteristics and without the driver
having to touch the accelerator or
brake pedals.
In order for it to be memorised, the
vehicle speed must be greater than
25 mph (40 km/h) or 40 mph (60
km/h), (according to engine).Operation
Place the ring of switch 1in the ON
position. The indicator light
will come on accompanied
by an audible signal.
A speed can be memorised.
Place the ring of switch 1 in the
OFF position to cancel.
Memorising a speed
As soon as you reach the chosen
speed, push stalk 1upwards or
downwards. This memorises the
speed, which will be maintained
automatically.
Note : it is possible to accelerate
momentarily without disarming the
cruise control.
Cancelling the memorised
speed
If you wish to cancel the memorised
speed :
Pull stalk 1towards you or press
the brake or clutch pedal.
Recalling the memorised
speed
After cancellation, flick stalk
1 upwards or downwards. Your vehicle
will return to the last memorised speed.
Changing a memorised speed
To memorise a speed higher than
the previous one:
keep stalk 1pressed upwards;
release it when you have reached
the required speed.
To memorise a speed lower than the
previous one : keep stalk 1pressed downwards;
release it when you have reached
the required speed.
Disarming the cruise control place the ring in the OFFposition
or switch off the ignition.
Do not use cruise control
on slippery roads or in
heavy traffic.
Page 132 of 167
YOUR 607 IN DETAIL
130
In the "OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is
removed, turn the air bag slot to the" ON " position to re activate the air
bag and thus ensure the safety of
your passenger in the event of an
impact.
Operating check
This is confirmed by an indicator
light, accompanied by an audible
signal and a message on the
multi–function display.
With the ignition on (2nd
notch), illumination of this
warning light accompanied
by an audible signal and the
message "Passenger air
bag disarmed" on the multi function
display, indicates that the passenger
air bag is disarmed (slot in the
"OFF" position). SIDE AIR BAGS AND
CURTAIN AIR BAGS
The side air bags are incorporated
into the frame of the front seat back,
on the door side.
The curtain air bags are incorporated
into the door pillars and the upper
part of the passenger compartment.
They are deployed independently of
each other depending on which side
the collision occurs.
Operating check
This is confirmed by a light on the
instrument panel, accompanied by
an audible signal and a message on
the multi–function display.
If this indicator light comes
on, accompanied by an
audible signal and the mes
sage 'Air bag(s) faulty' ,
contact a PEUGEOT dealer
to have the system checked.