ECO mode Peugeot iOn 2018 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2018, Model line: iOn, Model: Peugeot iOn 2018Pages: 136, PDF Size: 5.79 MB
Page 8 of 136
6
sudden movements and, if the conditions allow,
try to drive at a steady and moderate speed.For driving more
economically and greater
range
Practical everyday advice to optimise your
vehicle's range whilst conserving the energy of
your battery.
Drive smoothly
The electrical consumption of your vehicle
depends very strongly on the route you take,
your style of driving and your speed.
In all cases, adopt a smooth driving style.
Favour the use of the Eco zone indicated on
the energy consumption/generation indicator:
press the accelerator pedal gradually, without
Recover energy
Driving with anticipation allows you to recover
energy and increase the range of the vehicle.
Use the Charge zone in the energy
consumption/generation indicator whenever
possible: anticipate slowing traffic and, if the
conditions allow, favour the use of deceleration
over braking.
Control the use of your
electrical equipment
Excessive use reduces the range of your
vehicle significantly. Consider switching them
off as soon as you have reached the desired
level of comfort and check the settings at every
start.
Also limit the use of demisting and defrosting
and of the heated seat.
The heating and air conditioning operate using
energy supplied by the main battery.
Limit the causes of
excessive consumption
As with any vehicle, limit the load being
carried and keep aerodynamic resistance to a
minimum (leaving windows open above 30 mph
(50 km/h), roof bars, roof box, etc.).
Comply with servicing
instructions
Check the tyre pressures regularly and
follow the schedule of ser vicing operations
recommended by PEUGEOT.
Eco-driving
Page 9 of 136
7
Instrument panel
Dials
1.Main battery state of charge indicator.
Reminder of the drive selector position.
2. Energy consumption/generation indicator.
3. Speedometer.
Engine brake temporary reduction
i n d i c a t o r.
4. Display screen.
Display screen
A.Total distance recorder.
B. Trip distance recorder ( journey A or B).
C. Instrument panel lighting dimmer.
D. Distance remaining until service due.
E. Time remaining until service due.
F. Under-inflation detection.
G. Remaining range indicator.
Warning and indicator lamps
Visual identifiers informing the driver that
a system is in operation, switched off (on/
off indicator lamps) or has developed a fault
(warning lamp).
When the ignition is switched on
Certain warning lamps come on for a few
seconds when the vehicle's ignition is switched
on.
When the vehicle is started, these same
warning lamps should go off.
If they remain on, before driving refer to the
information on the warning lamp concerned.
Associated warnings
The illumination of certain warning lamps may
be accompanied by an audible signal.
There are two types of lighting for warning
lamps, fixed (continuous) or flashing.
Certain warning lamps may come on in
one of two modes. Only by relating the
type of lighting to the operating status of
the vehicle can it be ascertained whether
the situation is normal or whether a fault
has occurred.
5.
Display screen management button.
Displays the different functions
su c c e s s i ve l y.
Resets the selected function to zero (trip
distance recorder or service indicator).
Sets the lighting dimmer intensity.
Panel that brings together the different dials
and vehicle operation indicator lamps.
1
Dashboard instruments
Page 24 of 136
22
Closing
F Pull the handle B and guide the tailgate downwards.
F
R
elease the handle and gently press on the
outside sur face of the tailgate to close it.
Electric windows
System designed for opening or closing a
window manually or automatically. Equipped
with a deactivation system to prevent misuse of
the rear controls. 1.
Driver's electric window.
2. Passenger's electric window
3. Rear right electric window.
4. Rear left electric window.
5. Deactivating the passenger and rear
window controls.
Operation
With the ignition on:
F
P ress the control to open or pull it to close,
without passing the point of resistance.
The window stops as soon as the control is
released. The electric window controls remain
operational for approximately 30
seconds
after switching off the ignition.
The windows can no longer be opened or
closed once the driver's door is closed.
Deactivating the passenger and
rear window controls
F For your children's safety, press control 5 to deactivate the passenger and rear window
controls irrespective of their position.
If the button is pushed, operation is deactivated.
If the button is raised, operation is reactivated.
Automatic mode (driver's side)
F P ress the control beyond the point of
resistance to open. The driver's window
opens fully when the control is released.
F
P
ressing the control again stops the
movement of the window.
Access
Page 37 of 136
35
Buttons
1.On/off, data transmission.
2. MODE: allows you to scroll through the
different available functions (charge start,
charge duration, thermal comfort).
3. Immediate vehicle charging (reset
programmings to zero).
4. Settings.
Display screen
1.Data transmission status indicator.
2. Recharge indicator.
3. Fault indicator.
4. Battery charge status indicator.
5. Recharge programming function status
i n d i c a t o r.
6. Charge time remaining indicator.
7. Thermal comfort function status indicator.
On/Off
Extend the aerial.
Press and hold this button to switch
the remote control on or off.
The remote control will switch off
automatically if no action takes place
within thirty seconds.
Charge start programming
This function is used to set the remaining time
before starting to charge your vehicle.
(Example: it is 7 p.m. when the system is
programmed and the programmed charge time
is two hours: charging will start at 9 p.m.).
Switch on the remote control.
This symbol is displayed on the
screen.
Use the arrows to adjust the charge start time:
each press adjusts the time in half-hourly
intervals.
Press the on/off button briefly to send the data
to the vehicle.
3
Ease of use and comfort
Page 45 of 136
43
Windscreen wipers
A.Wiping speed control lever: raise
or lower the lever to the desired
position.
Single wipe.
Of f.
Intermittent (manually adjustable
speed).
Slow.
Fast.
B. Intermittent adjustment ring.
F
T
urn this ring to increase or
decrease wiping frequency in
intermittent mode.
Front screenwash
Pull the wiper control stalk towards you. The
screenwash and then the wipers operate for a
preset time.
Rear wiper
C. Rear wiper selection ring.
Of f.
Intermittent wiping.
The wiper wipes twice then switches to
intermittent mode with an inter val of a few
seconds. Wash-wipe.
Hold the ring in this position to operate the
screenwash and to carry out several wipes with
the wipers.
Courtesy lamp
Position 1 "ON"
The courtesy lamp is permanently on.
Position 2 "●"
The courtesy lamp comes on when a door or
the boot is opened; when the door or boot is
closed again, the lighting dims gradually for a
few seconds before going out.
However, the courtesy lamp goes out
immediately when the doors and boot are
closed and you lock the vehicle from the inside
or with the remote control.
4
Lighting and visibility
Page 73 of 136
71
This system still requires you to check the
tyre inflation pressure every month as well
as before a long journey.
Driving with under-inflated tyres impairs
handling, extends braking distances and
causes premature tyre wear, particularly
in adverse conditions (heavy loads, high
speeds, long journeys).Driving with under-inflated tyres
increases fuel consumption.
The tyre pressure specifications for your
vehicle can be found on the tyre pressure
label.
For more information on the
Identification markings , refer to the
corresponding section.
Tyre pressures should be checked when
the tyres are "cold" (vehicle stopped for
1
hour or after a journey of less than
6
miles (10 km) at moderate speeds).
Other wise, add 0.3
bar to the values
indicated on the label.Under-inflation alert
This is indicated by the fixed
illumination of this warning
lamp.
F
R
educe speed immediately, avoid excessive
steering movements and sudden braking.
F
S
top as soon as it is safe to do so.
Detection of loss of pressure does not
always bring about a visible deformation
of the tyre. Do not make do with just a
visual check.
F
C
heck the pressures of the four tyres
when "cold" using the compressor from the
temporary puncture repair kit.
If it is not possible to carry out this check
straight away, drive carefully at reduced
speed.
or
F
I
n case of a puncture, use the temporary
puncture repair kit. The alert persists until the reference
pressure values are reinitialised once the
tyre or tyres concerned are reinflated,
repaired or replaced. In case of tyre repair
or replacement, the sensor identifiers
must be logged by a PEUGEOT dealer or
a qualified workshop.
Resetting the reference
pressures
The system must be reinitialised after any
adjustment to the pressures of one or more
tyres, and after changing one or more wheels.
Before reinitialising the system, ensure
that the pressures of the four tyres are
correct for the use of the vehicle and in
line with the recommendations on the tyre
pressure label.
The under-inflation detection system
does not give a warning if a pressure is
incorrect at the time of reinitialisation.
6
Driving
Page 113 of 136
1
Bluetooth® audio system
Contents
First steps
1
R
adio 2
Media
3
T
elephone
6
Audio settings
8
C
onfiguration
8
Frequently asked questions
9
F
or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode. After a battery disconnection, a code must
be entered to access the audio system
functions.
You can try five times at most. There is
approximately fifteen minutes waiting time
between each of the last two tries.
Go to the end of this document to recover
the label indicating the code:
First steps
On/Off, volume adjustment.
Adjust audio options: sound
ambience, treble, bass, loudness,
distribution, left/right balance, front/
rear balance, automatic volume.
Automatic search for a lower radio
frequency.
Select the previous CD, USB track.
Scroll in a list.
Press and hold: rewind.
Display the list of stations received,
the CD/USB tracks or folders.
Press and hold: update the list of
stations received.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a higher radio
frequency.
Select the next CD, USB track.
Scroll in a list.
Press and hold: fast for ward.
Access to the main menu.
.
Bluetooth® audio system
Page 115 of 136
3
Select or deselect "RDS " to switch
RDS on or off.
Confirm with " OK" to save the
setting.
Receiving TA messages
The TA (Traffic Announcement) function
gives priority to TA alert messages.
To operate, this function needs good
reception of a radio station transmitting
this type of message. When a traffic
report is transmitted, the current audio
source (radio, CD, USB, etc.) is interrupted
automatically to play the TA message.
Normal playback resumes at the end of
the transmission of the message.
Press MENU .
Select "Radio ".
Select or deselect " TA" to activate
or deactivate the reception of traffic
messages.
Confirm with " OK" to save the
setting.
Displaying RADIO TEXT
Radio Text is information transmitted by
the radio station related to the current
programme or song.
With the radio displayed on the
screen, press MENU .
Select " Radio".
Select or deselect " TXT" to activate
or deactivate the display of Radio
Te x t .
Confirm with " OK" to save the
setting.
Media
USB port
This unit comprises a USB port and a jack
socket, depending on model. The system constitutes playlists (in
temporary memory), whose creation time
can be from a few seconds to several
minutes at the first connection.
Limiting the number of non-music files and
the number of folders reduces this waiting
time. The playlists are updated every
time the ignition is switched off or a USB
memory stick is connected.
The lists are memorised: if there is no
change in the lists, the next loading time
will be shorter.
Connect a USB memory stick to the USB port
or connect a USB device to the USB port using
a suitable cable (not supplied). To protect the system, do not use a USB
hub. Press SRC/TEL repeatedly to select
" USB ".
Press one of these buttons to select
the previous or next track in the list.
.
Bluetooth® audio system
Page 116 of 136
4
Press one of these buttons to select
the next or previous folder in the
order chosen.
Press and hold one of these buttons
for fast for ward or rewind.
Press LIST to display the structure
of the folders in the compilation.
Select a line in the list.
Confirm with " OK".
Go up a level in the structure.
Press MENU .
Select " Media ".
Select or deselect " TA" to activate
or deactivate the reception of traffic
messages.
Select the play mode: " Normal",
" Random ", "Random all" or
" Repeat ".CD player
Insert a CD in the player; play begins
automatically.
Insert an MP3 compilation in the CD player.
The audio system searches for all of the music
tracks, which may take anything between a few
seconds and several tens of seconds, before
play begins.
Press the SRC/TEL button
repeatedly to select " CD".
Press one of these buttons to go to
the previous/next track in the list.
Press one of these buttons to select
the previous or next folder in the
order chosen.
Press and hold one of these buttons
for fast for ward or rewind.
Press LIST to display the structure
of the folders of the compilation.
Select a line in the list.
Confirm with " OK". Return to the top level of the folder structure to
select the order of tracks.
-
By Folders (CD or USB): all folders
containing audio files recognised on the
peripheral device, in alphabetical order
without following the folder structure.
-
By Artist (USB only): all of the artist names
defined in the ID3 Tags, in alphabetical
o r d e r.
-
By Genre (USB only): all of the genres
defined in the ID3 Tags.
-
By Playlist (CD or USB): if playlists have
been saved.
Information and advice
The audio system will only play files with
".mp3", ".wma" and ".wav" extensions on a CD
and can also play files with ".ogg" extension
only on USB.
It is recommended that file names be of no
more than 20 characters and avoiding special
characters (e.g. « ? ; ù :) so as to avoid any
problem reading or displaying the files.
In order to be able to play a recorded CDR or
CDRW, when recording it is preferable to select
ISO 9660 level 1 or 2 standards or the Joliet
standard.
If the disc is recorded in another format, it may
not be played correctly.
Bluetooth® audio system
Page 123 of 136
11
Sound cut-outs of 1 to 2 seconds in radio mode. During this brief sound cut-out, the RDS
searches for any frequency permitting better
reception of the station. Deactivate the RDS function if the phenomenon
is too frequent and always on the same route.
Traffic announcement TA is displayed. I do not
receive any traffic information. The radio station does not broadcast traffic
information.Tune to a radio station which broadcasts traffic
information.
The stored stations are not found (no sound,
87.5
MHz is displayed...). An incorrect waveband is selected.
Press the SRC/ TEL button to return to the
waveband (FM1 or FM2) on which the stations
are stored.
The CD is ejected every time or is not played. The CD is upside down, cannot be read, does not contain audio files or contains audio files
of a format that cannot be played by the audio
system.
The CD is protected by an anti-pirating system
not recognised by the audio system.-
C
heck that the CD is inserted in the player
the right way up.
-
C
heck the condition of the CD: the CD
cannot be played if it is too badly damaged.
-
C
heck the content in the case of a recorded
CD: consult the advice in the "Audio"
section.
-
T
he audio system’s CD player does not play
DVDs.
-
B
ecause of low quality, certain burned CDs
will not be read by the audio system.
The CD sound is of poor quality. The CD used is scratched or of poor quality. Insert good quality CDs and store them in
suitable conditions.
The audio settings (bass, treble, ambiences) are
unsuitable. Return bass and treble settings to 0, without
selecting an ambience.
The Bluetooth connection cuts out. The battery of the peripheral device may not be
sufficiently charged.Charge the battery of the peripheral device.
The "USB peripheral/device error" or "Peripheral/Device
not recognised" message appears on the screen.The USB memory stick is not recognised. Use only USB memory sticks formatted to
FAT 32 (28 -bit file allocation table).
.
Bluetooth® audio system