light Peugeot Partner VP 2004 Owner's Guide

22-12-2003
YOUR PARTNER IN DETAIL91
In the
"OFF" position, the passen-
ger air bag will not be triggered in the event of an impact. As soon as the child seat is remo- ved, turn the air bag slot to the "ON"
position to re-activate the air bagand thus ensure the safety of yourpassenger in the event of an impact. Operating check
With the ignition on (2nd notch), illumination of thiswarning light indicates thatthe passenger air bag isdisarmed (switch in the"OFF"position).SIDE AIR BAGS* These are incorporated into the frame of the front seat backs, on thedoor side. They are deployed independently of each other depending on which sidethe collision occurs, in collisionswhich could cause injury to thechest, the abdomen or the head. Air bag fault
If this warning light comes on, accompanied by anaudible signal, contact a
PEUGEOT dealer to havethe system checked.
* According to destination.

22-12-2003
PRACTICAL INFORMATION
100
Refitting the wheel
- After positioning the wheel, lightly pre-tighten the bolts using the wheelbrace.
- Compress the jack and release it.
- Fully tighten the bolts using the wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it on using the
palm of the hand.
Replacing the wheel in the carrier
- Replace the chock 2in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt.
- Stow the wheelbrace and the jack.
For your safety, always change a wheel:
- on level, stable and non slippery ground,
- with the handbrake applied,
- with first or reverse gear engaged,
- with the vehicle chocked.
- never go underneath a vehicle raised using a jack (use an axle stand).
After changing the wheel
- Have the tightening of the bolts and the pressure of the spare tyre checked as soon as
possible by a PEUGEOT dealer.
- Have the punctured tyre repaired and replace it on thevehicle as soon as possible.

22-12-2003
PRACTICAL INFORMATION
102
CHANGING A BULB Front lights
1 - Dipped beam headlamps / Main beam headlamps
(H4-60/55W)
- Turn and remove the protector A.
- Disconnect the connector.
- Unclip the spring.
- Remove and replace bulb. 2 - Side lights (W 5 W)
- Turn and remove the protector
A.
- Pull the bulb holder rearwards.
- Change the bulb.
3 - Direction indicators (PY 21 W amber)
- Turn the bulb holder Ba quarter turn and remove it.
- Change the bulb. Note: in certain weather conditions (low temperatures,
humidity), the presence of condensation on the inside
of the headlamp glass is normal ; it disappears a few
minutes after the lights have been switched on.

22-12-2003
PRACTICAL INFORMATION
104
Rear lights
1 - Fog lamp (P 21 W).
2 - Direction indicators (P 21 W).
3 - Reversing lights (P 21 W).
4 - Brake lights/Side lights
(P 21/5 W). - Open the rear door.
- Unscrew the nut
A.
- Push the light unit gently towards the interior of the vehicle to unclip the two side retaining clips.
- Remove the light unit and discon- nect it.
- Unclip the bulb holder by pressing the tabs B,
- Change the faulty bulb.
Rear lights protective grille Unscrew the wing nuts C, and
remove the protective grille.
Number plate lights (W 5 W) Unclip the translucent protector to gain access to the bulb.

Third brake light (tailgate) (W5W) With the tailgate open, unscrew the two nuts.
 Unclip the support to gain accessto the bulbs.
 Change the faulty bulb. Third brake light (rear leftdoor) (W5W) 
Remove the housing cover by pressing the tab A(round
section) at the end of the light.
 Pull the housing cover rearwards. 
Squeeze the two tabs Bto
remove the bulb holder.
 Pull the faulty bulb and change it.
To refit, proceed in the reverse order.
PRACTICAL INFORMATION 105
22-12-2003

PRACTICAL INFORMATION109
22-12-2003
Fuse N¡ Rating
Functions
1 10A Pre-heat unit (diesel) - Brake and clutch switches - Reversing light.
2 15A Fuel pump.
3 10A ABS control unit or ESP control unit.
4 10A Engine control unit.
5- Not used.
6 15A Front fog lamps.
7 20A Headlamp wash pump.
8 20A Fan assembly relay - Engine control unit.
9 15A Left-hand dipped beam.
10 15A Right-hand dipped beam.
11 10A Left-hand main beam.
12 10A Right-hand main beam.
13 15A Horns.
14 10A Front and rear windscreen wash pumps.
15 30A Oxygen sensor - Air flow sensor.
16 30A Air pump relay.
17 30A Front windscreen wiper.
18 40A Air conditioning fan.

Fuse RatingFunctions
1 15A Rear wiper (hinged doors) - Rear 12 V sockets.
4 20A Multi-function display - Instrument panel - Audio equipment - Steering wheel controls.
5 15A Alarm siren.
6 10A Diagnostic socket.
7 15A Alarm.
9 30A Heated seats - Zenith roof fan.
10 40A Rear screen and mirror demisting.
11 15A Rear windscreen wiper (tailgate).
12 30A Front electric windows - Sunroof.
14 10A Engine fuse box - Steering wheel controls - Rain sensor.
15 15A Instrument panel - Multi-function display - Audio equipment.
16 30A Locking/unlocking controls for doors, bonnet and boot.
20 10A Right-hand brake light.
21 15A Left-hand brake light.
22 20A Front courtesy light - Map reading light - Lighter - Front 12 V socket -
Electric mirror.
PRACTICAL INFORMATION 107
22-12-2003

PRACTICAL INFORMATION
110
22-12-2003
BATTERY
To charge the battery using a battery charger:
- Disconnect the battery,
- Follow the instructions for use given by the battery charger manufacturer,
- Reconnect starting with the negative (-) terminal,
- Check that the terminals and connectors are clean. If they are covered with
sulphate (white or greenish deposit), disconnect them and clean them.
To start the vehicle from another battery:
- Connect the red cable to the positive (+) terminals of the two batteries,
- Connect one end of the green or black cable to the negative (-) terminal of the slave battery,
- Connect the other end of the green or black cable to an earth point on the broken down vehicle as far as possible from the battery.
Operate the starter, let the engine run.
Wait for the engine to return to idle, then disconnect the cables.
- Never disconnect a terminal when the engine is running.
- Never charge a battery without first disconnecting the terminals.
- After every reconnection of the battery, switch on the ignition and wait 1 minute before starting to allow the electronic systems to be initialised. If slight difficulties are experienced after this, please
contact a PEUGEOT dealer. A flat battery will preventthe engine from starting.
It is advisable to disconnect the battery if the vehicle is not to
be used for a period of more than one month.
ECONOMY MODE FUNCTION After the engine has stopped, with the key in the accessories position, certain
functions (windscreen wiper, electricwindows, courtesy lights, audio equipment etc.) can only be used forthirty minutes, to prevent discharging
the battery.
Once the thirty minutes are over, the message "Eco mode active" appears
on the multifunction display and the
active functions are put on standby.

TOWING A TRAILER,
CARAVAN, BOAT etc.
Only use original PEUGEOT tow bars that have been tested andapproved from the design stage of
your vehicle. The tow bar must be
fitted by a PEUGEOT dealer.
Your vehicle is primarily designed for transporting people and luggagebut it may also be used for towing a
trailer. Driving with a trailer subjects the towing vehicle to more significantstress and its driver must be particu-larly careful. Air density decreases with altitude, thus reducing engine performance.Above 1000 metres, the maximumtowing load must be reduced by 10% and so on for every 1000 metres of altitude.Driving advice Distribution of loads :
Distribute the
load in the trailer so that the heaviest items are as close as possible to theaxle and the nose weight approachesthe maximum permitted without exceeding it. Cooling : Towing a trailer on a slope
increases the temperature of the coolant. As the fan is electrically controlled, its cooling capacity is not dependenton the engine speed.
On the contrary, use a high gear to lower the engine speed and reduceyour speed. The maximum towing load on a long slope depends on the gradient andthe outside temperature. In all cases, pay attention to the coolant temperature. If the warning light comes on, stop
the vehicle and switch off the engineas soon as possible. Tyres :
Check the tyre pressures of
the towing vehicle and of the trailer,observing the recommended pressures. Braking : Towing increases the
braking distance.Lights : Check the electrical signalling
on the trailer.Side wind : Take into acount the
increased sensitivity to side wind.
PRACTICAL INFORMATION 113
22-12-2003