tailgate Peugeot Rifter 2019 User Guide

169
Activation
The function will be deactivated:
- I f a trailer is attached or a bicycle
carrier is fitted on a
towing device
(vehicle fitted with a
towing device
installed in line with the manufacturer's
recommendations).
-

A
bove about 6 mph (10 km/h).
-

O
n opening the tailgate.
-

W
hen shifting out of reverse (the image
remains displayed for 7
seconds).
-

B
y pressing the red cross in the top
left-hand corner of the touch screen.
Check the cleanliness of the camera lens
regularly.
Clean the reversing camera regularly
using a
soft, dry cloth.
When washing your vehicle at high-pressure,
direct the spray from at least 30
cm away from
the cameras and parking sensors.
When the sub-menu is displayed, select one of
the four views:
"Standard view".
"180° view".
Activation is automatic on engaging reverse at
a

speed lower than 6

mph (10

km/h).
You can choose the display mode at any time
by pressing on this area.
AUTO mode
Standard view
This mode is activated by default.
Using sensors in the rear bumper, the
automatic view changes from a rear view
(standard) to a
view from above (zoom), as an
obstacle is approached at the level of the red
line (less than 30
cm) during a manoeuvre.
The area behind the vehicle is displayed on the
screen.
The images provided by the camera may
be distorted by the relief.
In the presence of areas in shade, or in
conditions of bright sunlight or inadequate
lighting, the image may be darkened and
with lower contrast.
"Zoom view".
"AUTO m o de".
6
Driving

174
Operating limits
- The system may suggest an inappropriate parking space (parking prohibited, work
in progress with damaged road sur face,
location alongside a
ditch, etc.).
-

T
he system may indicate that a space
was found but will not offer it because of
a
fixed obstacle on the opposite side of
the manoeuvre which would not allow the
vehicle to follow a
trajectory required for
parking.
-

T
he system is not designed for per forming
the parking manoeuvre on a


sharp curve.
-

T
he system does not detect spaces that are
much larger than the vehicle itself or that
are delimited by obstacles that are too low
(pavements, studs, etc.) or too thin (trees,
posts, wire fences, etc.).
-

C
ertain obstacles located in the sensors'
blind spots may not be detected or no
longer be detected during the manoeuvre.
-

C
ertain materials (fabrics) absorb sound
waves: pedestrians may not be detected.
-

A f
ront or rear impact to the vehicle can
upset the sensor settings which is not
always detected by the system: distance
measurements may be falsified. The vehicle's sensors and camera(s) may be
impaired by:
-

a
ccumulated snow or fallen leaves on the
road,
-
a

dverse weather conditions (heavy rain,
thick fog, falling snow),
-
nois

e interference from noisy vehicles and
machinery (lorries, pneumatic drills, etc.).
Do not use the function under the
following exterior conditions:
-

A
longside a soft shoulder (ditch, etc.)
or quay or on a
cliff edge.
-

W
hen the road sur face is slippery (ice,
e t c .)
Do not use the function in presence of one
of the following malfunctions:
-

U
nder-inflation of a tyre.
-

I
f one of the bumpers is damaged,
-

I
f one of the cameras is faulty.
Maintenance
recommendations
- Regularly check that the sensors and cameras are clean.
I

f necessary, clean the camera lenses with
a
soft, dry cloth.
-

I
f using a high-pressure washer, do not
direct the spray less than 30
cm from the
sensors and cameras.
-

I
n bad weather, or during the winter, ensure
that the sensors and cameras are not
covered with mud, ice or snow. Do not use the function in presence of one
of the following modifications:
-

W
hen carrying an object extending
beyond the vehicle size (ladder on
the roof bars, bicycle carrier on the
tailgate, etc.).
-
W
ith a non-approved towball in place.
-
W
ith snow chains fitted.
-
W
hen driving on a small-diameter or
"space-saver" type spare wheel.
-
W
hen the wheels fitted are a different
size from the original ones.
-
A
fter modifying one or both bumpers
(added protection, etc.).
-
I
f the sensors have been repainted
outside the PEUGEOT dealer network.
-
W
ith sensors not approved for your
vehicle.
-

I

f the boot is heavily loaded, the tilt of the
vehicle towards the rear may inter fere with
the distance measurements.
Driving

200
Access to the spare wheel
F Access to the spare wheel is from the rear.
F
I
f your vehicle is fitted with a towing device,
raise the rear of the vehicle using the
jack (must be at jacking point B ) to allow
sufficient space to remove the spare wheel.
Remove the spare wheel from the
carrier
F Depending on version, open the tailgate or the side-hinged doors.
F

A
ccess the carrier bolt, located on the rear
door sill. F

S
lacken the bolt using the wheelbrace until
the carrier is low enough to allow the carrier
hook to be disengaged.
F
R
elease the carrier from the hook, take the
spare wheel and place it next to the wheel
to be changed.
Refit the spare wheel in the
carrier
F Position the wheel facing the carrier.
F P rogressively return the wheel to the carrier
by pushing alternately from left to right until
it is clear of the hook fixing area.
F

E
ngage the carrier on the hook, then tighten
the bolt using the wheelbrace until the bolt
is completely tight.
In the event of a breakdown

207
Front foglamps
Ty p e D, H11
Model A
Model B
F

R
emove the two fastening screws of the
module.
F

R
emove the module from its housing.
F

I
nsert a flat screwdriver between the lamp
and the cover.
F

P
ull and lever to unclip the cover. To replace this type of bulb, you can also
contact a
PEUGEOT dealer or a qualified
workshop.
Rear lamps
For more information on Changing a bulb
and, in particular, the types of bulb, refer to the
corresponding section. F

P
ress the locking clip and disconnect the
connector.
F
T
urn the bulb holder a quarter turn anti-
clockwise.
F
R
emove the bulb holder.
F
R
eplace the faulty bulb.
To refit, carry out these operations in reverse
o r d e r.
With side-hinged doors/tailgate
1. Brake lamps/sidelamps.
Ty p e B , P21/5W
2. Direction indicators.
Ty p e B , PY21W (amber)
3. Reversing lamps.
Ty p e B , P21W
4. Foglamps.
Ty p e B , P21W
F

F
rom the inside, disconnect the electrical
connector at the rear of the lamps.
8
In the event of a breakdown

208
Take care to reposition the tabs and the supply
wire correctly to avoid trapping the wire.
After changing a rear direction
indicator bulb, the reinitialisation time is
approximately 2


minutes or more.
F

M

ove aside the tabs, then extract the bulb
h o l d e r.
F

R

emove the faulty bulb by pressing lightly
on it, then turning it a

quarter turn anti-
clockwise.
Number plate lamps
Ty p e A , W5W – 5W
With side-hinged doors
F Unclip the interior trim.
F
D isconnect the connector by moving aside
its tab.
F

T
urn the bulb holder a quarter turn anti-
clockwise.
F

C
hange the bulb.
F

P
ut the bulb holder back in place and
reconnect the connector.
F

P
ut the trim back in place.
With tailgate
F Remove the plastic lens using a screwdriver.
F

C
hange the bulb.
F

R
efit the plastic lens and press on it.
Third brake lamp
Ty p e A , W16W – 16W
F
U
nscrew the two nuts.
F

P
ush the pins.
F

I
f necessary, disconnect the connector to
remove the lamp.
F

C
hange the bulb.
F

R

emove the two fixing bolts using the Torx
key provided in your vehicle.
F

or more information on the Tool kit
, refer
to the corresponding section.
F
F
rom the outside, pull the whole lamp unit
towards you (with side-hinged doors )
or towards the centre of the vehicle (with
tailgate ). F

C

hange the bulb.
To refit, carry out these operations in reverse
o r d e r.
In the event of a breakdown

213
Charging the battery using
a battery charger
For optimum ser vice life of the battery, it is
essential to maintain an adequate state of
charge.
In some circumstances it may be necessary to
charge the battery:
-

i
f you only use your vehicle for short
journeys,
-

i
f the vehicle is to be taken off the road for
several weeks.
Contact a
PEUGEOT dealer or a qualified
workshop.
If you plan to charge your vehicle's battery
yourself, use only a
charger compatible
with lead-acid batteries with a
nominal
voltage of 12
V.
Follow the instructions provided by the
manufacturer of the charger.
Never reverse polarities.
It is not necessary to disconnect the
battery.
F

S
witch off the ignition.
F

S
witch off all electrical consumers (audio
system, lamps, wipers, etc.). F

S
witch off the charger B before connecting
the cables to the battery, so as to avoid any
dangerous sparks.
F

E
nsure that the charger cables are in good
condition.
F

R
aise the plastic cover, if your vehicle has
one, on the (+) terminal.
F

C
onnect the cables of charger B as follows:
-

t
he positive (+) red cable to the (+)
terminal of battery A ,
-

t
he negative (-) black cable to earth point
C on the vehicle.
F

A
t the end of the charging operation, switch
off charger B before disconnecting the
cables from battery A . Never try to charge a
frozen battery – risk
of explosion!
If the battery has frozen, have it checked
by a
PEUGEOT dealer or by a qualified
workshop who will check that the internal
components have not been damaged and
that the container has not cracked, which
would mean a
risk of toxic and corrosive
acid leaking.
Disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of ser vice for a
long
period.
Before disconnecting the battery:
F

c
lose all of the accesses (doors, tailgate,
windows, roof), If this label is present, it is essential to
use only a
12 V charger to avoid causing
irreversible damage to the electrical
components related to the Stop & Start
system.
8
In the event of a breakdown