engine Peugeot Traveller 2016 Repair Manual

198
Traveller-VP_en_Chap06_conduite_ed01-2016
For Diesel vehicles, in sub-
zero temperatures the engine
will not start until the pre-heater
warning lamp has gone off.
If this warning lamp comes on
after pressing the "START/ST
oP

"
button, press down on the brake
or clutch pedal until the warning
lamp goes off, without pressing
the "START/ST
oP

" button again,
until the engine starts and runs.
Starting
F Then, press the " S TA R T/
STOP " button.
Starting-switching off the engine,
"Keyless
e
n
try and starting"
The steering column unlocks and the engine
starts more or less immediately.
F

P

lace the remote control inside the vehicle,
in the recognition zone.
F

I

f your vehicle has a manual gearbox, fully
depress and hold down the clutch pedal
until the engine starts. F
I
f your vehicle has an automatic gearbox,
place the selector at position P then press
the brake pedal firmly.
F

I

f your vehicle has an electronic gearbox,
place the selector at position N then press
the brake pedal firmly.
Driving

199
Traveller-VP_en_Chap06_conduite_ed01-2016
The presence in the recognition zone of
the remote control of the "Keyless en try
and Starting" system is essential.
Never leave the vehicle with the engine
running and with the remote control on
your person.
If the remote control leaves the
recognition zone, a message is
displayed.
Move the remote control into the zone
to be able to start the engine.
If one of the starting conditions is
not met, a message appears in the
instrument panel screen. In some
circumstances, it is necessary to
turn the steering wheel slightly while
pressing the "START/ST
oP

" button
to assist unlocking of the steering;
a message warns you when this is
needed. If the vehicle is not immobilised, the
engine will not stop.Switching off
F Immobilise the vehicle.
F
W
ith the remote control in the
recognition zone, press the
" START/STOP " button.
The engine stops and the steering column is
locked.
Ignition on
(without starting)
With the ignition on, the system
automatically goes into energy
economy mode to maintain an adequate
state of charge in the battery. With the Keyless
e
n
try and Starting
remote control inside the vehicle,
pressing the "START/ST
oP
" button,
with no action on the pedals , allows the
ignition to be switched on.
This also allows the accessories to be used
(for example: audio system, lighting...).
F
P
ress the "START/ST
oP
" button,
the instrument panel comes on
but the engine does not start.
F
P
ress the button again to switch
off the ignition and allow the
vehicle to be locked.
To avoid any risk of jamming of the
pedals:
-

o

nly use mats which are suited to
the fixings already present in the
vehicle; these fixings must be used,
-

n

ever fit one mat on top of another.
The use of mats not approved by
P
e

ugeo
T m

ay inter fere with access to
the pedals and hinder the operation of
the cruise control / speed limiter.
The mats approved by P
e

ugeo
T h

ave
two fixings located below the seat.
6
Driving

200
Traveller-VP_en_Chap06_conduite_ed01-2016
Back-up starting
Should your vehicle not detect the electronic
key in the recognition zone, because the
remote control battery is flat, a back-up reader
is provided to the left, behind the steering
wheel to allow starting.F

P
ress the "START/ST
oP
" button.
The engine starts. If the remote control is no longer in the
recognition zone when you close a door or
when you (later) request switching off the
engine, a message appears in the instrument
panel.
Forced switch-offRemote control not
recognised
F If you want to force switching off the
engine, press and hold the "START/SToP "
button for about 3 seconds, then contact a
P
e

ugeo
T d
ealer or a qualified workshop.
F

I

f your vehicle has a manual gearbox, place
the gear lever in neutral then fully depress
the clutch pedal.
F

I

f your vehicle has an automatic gearbox,
place the selector at position P then press
the brake pedal firmly.
F

I

f your vehicle has an electronic gearbox,
place the selector at position N then press
the brake pedal firmly.
In the event of an emergency only and with the
vehicle stationary, you can switch off the engine.
To do this, press and hold the "START/ST
oP

"
button for about 3 seconds.
In this case the steering column locks as soon
as the vehicle stops. F

P

lace and hold the remote control against
the reader, then:
Driving

201
Traveller-VP_en_Chap06_conduite_ed01-2016
Parking brake
F With your foot on the brake pedal, pull the parking brake lever up to immobilise your
vehicle.
F

W
ith your foot on the brake pedal, pull the
parking brake lever up gently, press the
release button then lower the lever fully. When parking on a slope, or on a steep
slope with a laden vehicle, turn the
wheels against the kerb then apply the
parking brake.
When the vehicle is being driven,
this warning lamp coming on,
accompanied by an audible signal
and a message, indicates that the
parking brake is still on or has not
been fully released. Pressing the brake pedal facilitates the
application and release of the manual
parking brake. If your vehicle has a manual gearbox,
engage a gear then switch off the
ignition.
If your vehicle has an automatic
gearbox, place the gear selector at
position P then switch off the ignition.
If your vehicle has an electronic
gearbox, place the gear selector at
position A then switch off the ignition.
Release on level ground Application
Anti-theft protection
Electronic engine immobiliser
The keys contain an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a malfunction, you are informed
by a message in the instrument panel screen.
In this case, your vehicle does not start; contact
a P
e

ugeo
T d
ealer if required.
For reasons of safety and theft
protection, do not leave your electronic
key in the vehicle, even when you are
close to it.
It is recommended that you keep it on
your person.
6
Driving

202
Traveller-VP_en_Chap06_conduite_ed01-2016
Hill start assist
System which keeps your vehicle immobilised
temporarily (approximately 2 seconds) when
starting on a gradient, the time it takes to
move your foot from the brake pedal to the
accelerator pedal.
It only operates when:
-
t
he vehicle is completely stationary, with
your foot on the brake pedal,
-
t

he driver’s door is closed.
This hill start assist system cannot be
deactivated.
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held momentarily when you
release the brake pedal.
On an ascending slope, with the vehicle
stationar y, the vehicle is held for a
momentarily when you release the brake
pedal
.
Operating fault
F If your vehicle has a manual gearbox, place
the lever in the first gear position or in
neutral.
F

I
f your vehicle has an automatic gearbox,
place the selector at position D or select
manual operation M .
F

I
f your vehicle has an electronic gearbox,
place the selector at position A or M .If a fault in the system occurs, this warning
lamp comes on accompanied by a message.
Contact a P
e

ugeo
T d
ealer or a qualified
workshop as soon as possible to have the
system checked.
Do not leave the vehicle while it is being
held in the hill start assist phase.
If you need to get out of the vehicle with
the engine running, apply the parking
brake manually then ensure that the
parking brake indicator lamp is on.
If your vehicle has an automatic
gearbox and you have to move off on
a steep slope (rising or falling) with a
loaded vehicle, press the brake pedal ,
select position D , release the parking
brake then release the brake pedal.
Driving

203
Traveller-VP_en_Chap06_conduite_ed01-2016
only engage reverse gear when the
vehicle is stationary with the engine at idle.
As a safety precaution and to facilitate
starting of the engine:
-
a
lways select neutral,
-

p
ress the clutch pedal.
6-speed manual gearbox
Engaging 5th or 6th gear
only engage reverse gear when the
vehicle is stationary with the engine at idle.
As a safety precaution and to facilitate
starting of the engine:
-
a
lways select neutral,
-

p
ress the clutch pedal.
5-speed
manual gearbox
F With the clutch pedal fully down, place the gear lever in neutral.
F

P
ush the gear lever to the right then
backwards.
Engaging reverse gear Engaging reverse gear
F Raise the ring under the knob and move
the gear lever to the left then for wards.
F
M
ove the lever fully to the right to engage
5th or 6th g e a r.
Failure to follow this advice may cause
permanent damage to the gearbox
(engagement of 3
rd or 4th gear by
m i st a ke).
6
Driving

204
Traveller-VP_en_Chap06_conduite_ed01-2016
gear shift indicator
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one or more gears.
You can follow this instruction without going
through the intermediate gears.-

Y
ou press the accelerator pedal.
-

Y
ou are in third gear.-

T
he system may suggest that you engage
a higher gear.
The information appears in the instrument
panel in the form of an arrow.
on v

ehicles with manual gearbox, the arrow
may be accompanied by the recommended
g e a r.
The system adapts its gear change
recommendation according to the
driving conditions (gradient, load,
...)
and the demands of the driver (power,
acceleration, braking,


...).
The system never suggests:
-
e

ngaging first gear,
-
enga

ging reverse gear.
System which reduces fuel consumption by recommending the most suitable gear.ex
ample:
on c

ertain BlueHDi Diesel versions
with manual gearbox, the system
may suggest changing into neutral
( N is displayed in the instrument
panel) so that the engine can go into
standby (ST
oP m

ode with Stop &
Start), in certain driving conditions.
This function cannot be deactivated. The gear engagement
recommendations must not be
considered compulsory.
This is because the configuration of
the road, traffic density and safety
remain impor tant factors in the
choice of the best gear.
The gear shift indicator system does not
replace the need for vigilance on the
part of the driver.
Driving

206
Traveller-VP_en_Chap06_conduite_ed01-2016
When you move the gear selector or press the
M button, the corresponding symbol appears in
the instrument panel.
P.

Park
R.
R

everse
N.


Neutral
D.
D

rive (automatic operation)
M.
M

anual operation
1 to 6.
g
ea
r engaged
-

I
nvalid value
Displays in the instrument panel
F With your foot on the brake, select position P . When the engine is running at idle, with
the brakes released, if position R
, D or
M is selected, the vehicle moves even
without the accelerator being pressed.
Never leave children in the vehicle
without supervision.
As a safety measure, never leave
the vehicle without taking your key or
remote control with you, even for a
short time.
When carrying out maintenance with
the engine running, apply the parking
brake and select position P .
If you have to move off on a steep slope
with a loaded vehicle, press the brake
pedal
, select position D , then release
the parking brake.
F

S

tart the engine.
If the conditions are not met, there is an audible
signal, accompanied by a message in the
instrument panel screen.
F

R

elease the parking brake.
F

Sel

ect position R , N or D.
F
g
r

adually release the brake pedal.
The vehicle moves off.
F

I

f the message " Foot on brake"
is displayed in the instrument
panel, press the brake pedal
f i r m l y.
Moving off
If P is displayed in the instrument panel
but the selector is in another position,
place the selector in position P to allow
the engine to be started.
If position N is engaged inadvertently
while driving, allow the engine to
return to idle then engage position D to
accelerate.
Driving

207
Traveller-VP_en_Chap06_conduite_ed01-2016
Automatic operation
Never select position N while the
vehicle is moving.
Never select position P or R unless the
vehicle is completely stationary.
Creep function (moving
without using the accelerator)
This function provides great flexibility in
manoeuvring the vehicle at low speed (when
parking, in traffic jams, …).
With the engine at idle, parking brake released
and position D, M or R selected, the vehicle
moves


as soon as you take your foot off
the brake pedal (even without pressing the
accelerator).
As a safety measure (children on
board), never leave the vehicle with the
engine running and the doors closed.
The gearbox then operates in auto-adaptive
mode, without any intervention on the part
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
vehicle.
For maximum acceleration, without
touching the selector press the
accelerator pedal down fully (kick-
down). The gearbox changes down
automatically or maintains the gear selected
until the maximum engine speed is reached.
on b

raking, the gearbox changes down
automatically to provide effective engine
braking.
If you release the accelerator sharply, the
gearbox will not change to a higher gear, for
safety reasons. F
Sel
ect position D for automatic
changing of the six gears.
You can temporarily take control of gear
changes using the "+" and " -" steering mounted
control paddles. The gear change instruction is
acted on if the engine speed permits.
This function allows you to anticipate certain
situations, such as overtaking another vehicle
or approaching a bend in the road.
Following a few moments with no action on
the control paddles, the gearbox returns to
automatic operation.
Temporary manual control of
gear changes
6
Driving

208
Traveller-VP_en_Chap06_conduite_ed01-2016
In manual mode it is not necessary to
release the accelerator pedal when
changing gear.
F

W

ith the selector in position D ,
press button M for sequential
changing of the six gears. M appears and the gears engaged
appear in succession in the
instrument panel.
F

I
t is possible to return to
automatic operation at any time
by pressing button M again.
It is only possible to change from one
gear to another if the vehicle speed and
engine speed permit.
Manual operation
If the engine speed is too low or too
high, the gear selected flashes for
a few seconds, then the actual gear
engaged is displayed.
When the vehicle is stationary or
moving very slowly, the gearbox
selects gear M1 automatically. To save the brakes when descending
a steep incline, use engine braking to
reduce your speed (take your foot off
the accelerator pedal or change down).
Keeping the brake pedal pressed
continuously for long periods can
overheat the brakes, with the risk of
damaging the braking system or making
it inoperative.
on

ly use the brakes when necessary, to
slow or stop the vehicle.
The indicator associated with the button comes on.
F
o
p

erate the " +" or " -" steering mounted
control paddle. The indicator associated with the button goes off.
Depending on the configuration of the
road (for example: mountain pass),
it may be preferable to use manual
operation.
This is because automatic operation
may not be best suited, not allowing the
use of engine braking.
Invalid value during manual
operation
This symbol is displayed if a gear is
not engaged correctly (gear selector
between two positions).
F

P

lace the selector "correctly" at a position.
Driving