display PONTIAC FIREBIRD 1995 User Guide

5.
6.
Press HR until the first one or two digits of your How to Change Your Security Code
code appear.
Press
A” If “- - -” shows, you have shut off steps:
You can change your security code by following these
the theft-deterrent feature. If SEC shbws, your audio
system is still secured.
Note: If you lose or forget your security code, see your
dealer for assistance.
Unlocking the Audio System “after a Power Failure
If power is disrupted io the audio system whiie in the
SEC mode, the unit will not work &nd LOC will show
on the display whenever the ignition is on. To unlock the
unit:
1. Press MIN “OW’ will appear on the display.
2. Press MIN again and hold until the iast two digits of
your code appear. Release the button.
3. Press HR until the first one or two digits of your
code appear.
4. Press AM/FM. SEC will appear on the display and
the unit will work.
If LOC shows, the numbers did
not hatch and the unit is still locked.
-
1. Using your old code, follow the directions given
under “Shutting Off the Theft-Deterrent Feature.’’
2. Repeat directions of .“Setting Your Security Code”
with your new security code.
Understanding Radio Reception
FM Stereo
.i‘
FM stereo will give you the best sound. But FM signals
will reach only about
10 to 40 miles (1 6 to 65 km). And,
tall buildings or hills can interfere with
FM signals,
causing the sound to come and go.
AM
The range for most AM .stations is greater than for FM,
especially at night. The longer range, however, can
cause stations to interfere with each other. AM can pick
up noise
from things like storms and power lines. Try
reducing the treble to reduce this noise if you ever get it.
&&
3-13
ProCarManuals.com

Care of Your Cassette Tape Player
A tape player that is not cleaned regularly can cause
reduced sound quality, ruined cassettes, or a damaged
mechanism. Cassette tapes should be stored in their
cases away from contaminants, direct sunlight, and
extreme heat.
If they aren’t, they may not operate
properly
or cause failure of the tape player.
Cassettes are subject to wear and the sound quality may
degrade over time. Always verify that the cassette tape
is in good condition and that the tape player is clean
before obtaining service on your tape player.
Your tape player should be cleaned with every 50 hours
of use to provide optimum performance. Your radio may
display “Cln” to indicate that your have used your tape
player for
50 hours without resetting the tape clean
timer.
If you notice a reduction in sound quality,
regardless of when the tape player was last cleaned, try
playing a different cassette to see if the tape or the tape
player is at fault. If the second cassette results in no
improvement in sound quality, try cleaning the tape
player.
Proper tape player cleaning should be done with a
scrubbing action, nonabrasive cleaner cassette. This is a
wet-type cleaning system that uses a cleaning cassette
with pads which scrub the tape head as the hubs of the
cleaner cassette
turn. To properly clean your tape player,
follow the instructions with the cleaning cassette.
If you
use this type of cleaner, the radio may display an error
and eject the cartridge. This is normal and is the result
of an added feature in the tape player that detects broken
tapes. If an error occurs, you will need to insert the
cleaning cassette at least three times to thoroughly clean
the tape player.
You may also choose a non-scrubbing action, wet-type
cleaner which uses a cassette with a fabric belt to clean
the tape head.
This type of cleaning cassette will not
eject. It may not clean as thoroughly as the scrubbing
type cleaner.
A scrubbing action cleaner is available through your
dealer
(GM Part No. 12344600).
Note: Tape adapter kits for portable CD players will not
work in your cassette player. These adapters will cause
the radio to display an error message and the adapter
cassette will be ejected.
3-15
ProCarManuals.com