change wheel PONTIAC FIREBIRD 1996 Owners Manual
[x] Cancel search | Manufacturer: PONTIAC, Model Year: 1996, Model line: FIREBIRD, Model: PONTIAC FIREBIRD 1996Pages: 386, PDF Size: 19.18 MB
Page 92 of 386

Tilt Steering Wheel Turn SignaVMultifunction Lever
A tilt steering wheel allows you to adjust the steering
wheel before
you drive.
You can also raise it to the highest level to give your
legs more room when you exit and enter the vehicle.
To tilt the wheel, hold the steering wheel and pull the
lever. Move the steering wheel
to a comfortable level,
then release the lever to lock the wheel in place. The
lever on the left side of the steering column
includes your:
Turn Signal and Lane Change Indicator
e Headlamp Highkow Beam and Passing Signal
e Windshield Wipers
Windshield Washer
Cruise Control (Option)
2-43
ProCarManuals.com
Page 96 of 386

When you apply your brakes, or push the clutch pedal, If
your vehicle is in cruise control when the optional
if you have a manual transmission, the cruise control traction control system
begins to
limit wheel spin, the
shuts off. cruise control will automatically disengage. (See
“Traction Control System’’ in the Index.) When road
conditions allow you to safely use
it again, you may turn
the cruise control back on.
Setting Cruise Control
can’t drive safely at a steady speed.
So,
don’t use your cruise control on winding
roads or in heavy traffic.
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don’t
use cruise control on slippery roads.
0 Cruise control can be dangerous on If you leave your cruise control switch on when
yodre not using
cruise, you might hit a button
and go into cruise when you don’t want to. You
could be startled and even lose control. Keep the
cruise control switch
OFF until you want to use it.
2-47
ProCarManuals.com
Page 169 of 386

Remember: Anti-lock doesn’t change the time you need
to get your foot up to the brake pedal or always decrease
stopping distance.
If you get too close to the vehicle in
front
of you, you won’t have time to apply your brakes
if that vehicle sudd’enly slows or stops. Alwayssleave
enough room up ahead to stop, even
though you have
anti-lock brakes.
Using Anti-Lock
Don’t pump the brakes. Just hold the brake pedal
down and let anti-lock work for you.
You may feel
the system working,
or you may notice some noise,
but this is normal.
LOW
TRAC
When your anti-lock system
is adjusting brake pressure
to help avoid a braking skid,
this light will come
on.
See ‘‘L’ow Traction Light”
in the
Index
naction Control, System
(Option: LTl VS Engine) I
Your vehicle may have a traction control system that
limits wheel spin. This is especially usefulin slippery
road conditions.
The system operates only if it senses that
one or both of
the rear wheels are spinning or beginning
to lose traction. When
this happens, the system works the
rear brakes and reduces engine, power (by closing the
throttle and managing engine spark) to limit wheel spin.
LOW
TRAC
This light will come on
when YQLU traction control
system is limiting wheel
spin. See “Low Traction
Light”
in the Index. You
may feel or hear the system
working, but this is normal.
The traction control system may operate on dry roads
under some conditions, and you may notice a reduction in
acceleration when this happen,€, This is normal and doesn’t
mean there’s
a problem with your vehicle. Examples of
fhese conditions include a hard acceleration in a turn, or an
ProCarManuals.com
Page 171 of 386

. If the traction control system is limiting wheel spin
when you press the button, the light on the button will
.go off and the warning light will come on -- but the
_. ._ ,system won't turn off right away. It will wait until
gathere's
no longer a current need to limit wheel spin. I
You can turn the system back an at any time by pressing
the button
again. The light on the button should come
on, and the traction control system w'arning light should
go off.
If your car is equipped with P245/50zR16 tires, the
traction control system will automatically
turn off at
speeds above 108 mph (1 74 km/h). (The traction, control
system waning light will not corn on.) When the
vehicle
speed drops below 103 mph (1 66 km/h) the
system will automatically come on again.
- Braking in Emergencies
Use your anti-lock braking system when you need to.
With anti-lock, you can steer and brake at the same
time. In many emergencies, steering can help you more
than even
the very best braking.
Steering
Power Steering
If you lose power steering assist because the engine
stops or the system
is not functioning, you can steer but
it will take much
more effort.
Steering Tips
Driving on Curves
It's important to take curves at a reasonable speed.
A lot of the "driver lost control" accidents mentioned on
the news happen on curves. Here's why:
Experienced driver or beginner, each of us
is subject to
the same laws
of physics when driving on curves. The
traction
of the tires against the road surface makes it
possible for the vehicle to change its path when you turn
the front wheels. If there's no traction, inertia will keep
the vehicle going in the same direction. If you've ever
tried to steer a vehicle on wet ice, you'll understand
this.
i ., _. .I ..
ProCarManuals.com
Page 175 of 386

0
0
0
0
Check your mirrors, glance over your shoulder, and
start your left lane change signal before moving out
of the right lane to pass. When you are far enough
ahead of the passed vehicle to see its front in your
inside mirror, activate your right
lane change signal
and move back into the right lane. (Remember that
your right outside mirror
is convex. The vehicle you
just passed may seem to be farther away from you
than
L it really is,)
Try not to pass more than one vehicle at a time
on two-lane roads. Reconsider before passing the
next vehicle.
Don’t
overtake a slowly moving vehicle too rapidly.
Even though the brake lamps
are not flashing,,it may
be slowing down or starting to turn.
If you’re being passed, make it easy for the
following driver to get ahead
of you. Perhaps you
can ease a little to the right.
Loss of Control
Skidding
In a skid, a driver can lose control of the vehicle.
Defensive drivers avoid
most skids by taking reasonable
care suited to existing conditions, and by not “overdriving”\
those conditions. But skids
are always possible.
The three types of skids correspond
to your Pontiac’s
three control systems. In the braking
skid, your wheels
aren’t rolling. In the steering or cornering skid, too
much speed or steering in a curve causes tires to slip and
lose cornering force. And in the acceleration skid, too
much throttle causes the driving wheels
to spin.
A cornering skid is best handled by easing your foot off
the accelerator pedal.
If you have the traction control system, remember: It
helps avoid only the acceleration skid.
If
you do not have traction control, or if the system is
off, then an acceleration skid is also best handled by
easing your foot off the accelerator pedal.
Let’s
review what driving experts say about what E your vehicle starts to slide, ease your foot off the
happens when the
three control systems (brakes, steering accelerator
pedal and quickly steer the way you want the
and acceleration) don’t have enough friction where the vehicle to
go. If you start steering quickly enough, your
tires meet the road to do what the driver has asked. vehicle may straighten
out. Always be ready for a
constantly seek an escape route or area of less danger. second
skid if it occurs.
. .-
. -- . r- _.. In any emergency, don’t give up. Keep trying to steer and ..
ProCarManuals.com
Page 193 of 386

Your car can tow a trailer if it is equipped with proper
trailer towing equipment.
To identify what the vehicle
trailering capacity
is for your vehicle, you should read
the infrwmakion in “Weight of the Tr~ler” that appears
later in this section. But trailering
is different than* just
driving your vehicle by itself. Trailering means changes
in handling, durability, and fuel economy. Successful,
safe trailering takes correct equipment, and it has
to be
used properly.
That’s the reason for this part. In it are
many
time-tested, important trailering tips and safety rules.
Many of these are important for your safety and that
of
your passengers. So please read this section carehlly
before you pull a trailer.
Load-pulling components such as the engine,
transmission, rear axle, wheel assemblies and tires
are
forced to work harder against the drag of the added
weight. The engine is required
to operate at relatively
higher speeds and under greater loads, generating extra
heat. What’s more, the trailer adds,considerably to wind
resistance, increasing the pulling requirements.
I
_. . , _, -i .. :
If You Do Decide To Pull A Trailer
If you do, here,are some important points:
0
0
0
0
There are many different laws, including speed limit
restrictions, having to do with trailering. Make sure
your rig will
be legal, not only where you live but
also where you’ll be driving.
A good source for this
information can be state or provincial police.
Consider using
a sway control. You can ask a hitch
dealer about sway
controls.
Don’t tow a trailer at all during the first 1,000 miles
(1 600 km) your new vehicle is driven. Your eng-k,
axle or 0ther.part.s could be damaged.
Then, during the first
500 miles (800 km) that you
tow a trailer, don’t drive ov’er 50 mph (80 km/h) and
don’t make starts
at full throttle. This helps your
engine and other parts of your vehicle wear in at the
heavier loads.
Obey speed limit restrictions when towing a trailer.
Don’t drive faster than the maximum posted speed
for trailers (or no more than
55 mph (90 km/h)) to
save wear on your vehicle’s parts.
4-32
ProCarManuals.com
Page 198 of 386

Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle may need a
different ‘turn signal flasher and/or extra wiring. Check
with your Pontiac dealer.
The arrows
on your instrument panel will flash
whenever you signal a turn or lane change. Properly
hooked up, the trailer lamps will also flash, telling other
drivers you’re about to turn, change lanes or stop.
When towing a trailer, the arrows on your instrument
panel will flash for turns even if the bulbs on the trailer
are burned out. Thus, you may think drivers behind you
are seeing your signal when they are not. It’s important
to check occasionally to be sure the trailer bulbs are
still working.
1 ’ Driving On Grades
Reduce speed and shift to a lower gear before you start
down a long or steep downgrade.
If you don’t shift
down, you might have to use your brakes
so much that
they would get hot and no longer work well.
On
a long uphill grade, shift down and reduce your
speed to around
45 mph (70 km/h) to reduce the
possibility
of engine and transmission overheating.
If YOU are towing a trailer and you have an automatic
transmission with Overdrive, you may prefer to drive in
THIRD (D) instead of AUTOMATIC OVERDRIVE (0)
(or, as you need to, a lower gear). Or, if you have a
manual transmission with
FJFTH (5) (or SIXTH (6)) gear
and you are towing a trailer, it’s better not to use FIFTH
(5) (or SIXTH) (6) gear. Just drive in FOURTH (4) (drive
in
FIFTH (5) if you have a six-speed manual transmission)
or,
as you need to, a lower gear.
Parking on Hills
You really should not park your vehicle, with a trailer
attached, on a hill. If something goes wrong, your rig
could start to move. People can be injured, and both
your vehicle and the trailer can be damaged.
But if you ever have to park your rig on a hill, here’s
how to do it:
1. Apply your regular brakes, but don’t shift into
2. Have someone place chocks under the trailer wheels.
3. When the wheel chocks are in place, release the
regular brakes until the chocks absorb the load..
’
4. Reapply the regular brakes, Then apply your parking
brake, and then shift to
PARK (P), or REVERSE (R)
for a manual transmission.
5. Release the regular brakes.
PARK (P) yet, or into gear for a manual transmission.
4-37
ProCarManuals.com
Page 206 of 386

Towing Your Vehicle
Try to have a Pontiac dealer or a professional towing
service tow your Firebird.
If your vehicle has been changed or modified since it
was factory-new by adding aftermarket items like
fog
lamps, aero skirting, or special tires and wheels, these
instructions may not be correct.
Before you do anything, turn on the hazard
warning flashers.
When you call, tell the towing service:
That your vehicle cannot be towed from the front or
That you vehicle has rea-wheel drive.
0 The make, model and year of your vehicle!
rear
with sling-type equipment.
0 Whether you can still move the shift lever.
0 If there was an accident, what was damaged.
When the towing service arrives, let the tow operator
know that this manual contains detailed towing
instructions and illustrations. The operator may want
to see them.
I I
To help avoid injury to you OF others:
0 Never let passengers ride in a vehicle that is
0 Never tow faster than safe or posted speeds.
0 Never tow with damaged parts not fully
secured.
0 Never get under your vehicle after it has
been lifted
by the tow truck.
0 Always secure the vehicle on each side with
separate safety
chains when tswhg it.
0 Never use J-hooks. Use T-hooks instead.
being towed.
ProCarManuals.com
Page 226 of 386

If a Tire Goes Flat
It’s unusual for a tire to “blow out” while you’re driving,
especially
if you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But if you should ever have a “blowout,” here are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot
off the
accelerator pedal and grip the steering wheel
firmly.
Steer to maintain lane position, and then gently bralie to
a stop well out
of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may
require the same correction you’d use in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to
go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop
-- well off the road if possible.,
If a tire goes flat, the next part shows how to use your
jacking equipment to change a flat tire safely.
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly
to a level place. Turn on your hazard
warning flashers.
I
A CAUTILN:
Changing a tire can cause an injury. The vehicle
can slip off the jack and roll over
you or other
people. You and they could be
badly injured.
Find
a level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put an automatic transmission shift
lever in
PARK (P), or shift a manual
transmission to
FIRST (1) or
REVERSE (a).
3. Turn off the engine.
To be even more certain the vehicle won’t move,
you can put blocks
at the front and rear of the
tire farthest away from the one being changed.
That would be the tire on the other side of the
vehicle,
at the opposite end.
5-27
ProCarManuals.com
Page 234 of 386

4. Raise the vehicle by rotating the wheel wrench
clockwise. Raise the vehicle
far enough off the ground
SO there is enough room for the spare tire to fit.
Remove all the wheel nuts and take off the flat tire.
5. Remove any rust or dirt
from the wheel bolts,
mounting surfaces and
spare wheel.
A CAUTION:’
Rust or dirt on the wheel, or on the parts to
which it is fastened, can make the wheel nuts
become loose after a time. The wheel could come
off and cause an accident. When you change a
wheel, remove any rust or
dirt from the places
where the wheel attaches to the vehicle. In an
emergency, you can use
a cloth or a paper towel
to do
this; but be sure to use a scraper or wire
brush later,
if you need to, to get all the rust or
dirt off.
5-35
ProCarManuals.com