Temperature PONTIAC G6 2007 Owners Manual

3. Snap the front and back together tightly so
moisture will not get inside the transmitter.
4. Test the operation of the transmitter with the
vehicle.
Remote Vehicle Start
Your vehicle may have a remote starting feature.
This feature allows you to start the engine from
outside the vehicle. It may also start the vehicle’s
heating or air conditioning systems and rear
window defogger. When the remote start system
is active and the vehicle has an automatic climate
control system, it will automatically regulate the
inside temperature. Normal operation of the system
will return after the ignition key is turned to ON.
Laws in some communities may restrict the use
of remote starters. For example, some laws may
require a person using remote start to have the
vehicle in view when doing so. Check local
regulations for any requirements on remote
starting of vehicles.Do not use the remote start feature if your vehicle
is low on fuel. Your vehicle may run out of fuel.
The remote start feature provides two separate
starts per ignition cycle, each with 10 minutes of
engine running time.
The remote start feature needs to be reset after
your vehicle’s engine is started two times using
the transmitter’s remote start button. To reset the
remote start feature, insert the vehicle’s key into
the ignition switch and turn it to ON. SeeIgnition
Positions on page 122for information regarding the
ignition positions on your vehicle.
You can start your vehicle’s engine from
approximately 197 feet (60 m) away. However, the
range may be less while the vehicle is running,
and as a result you may need to be closer to your
vehicle to turn it off than you were to turn it on.
There are other conditions which can affect
the performance of the transmitter, seeRemote
Keyless Entry System on page 100for additional
information.
105

The remote vehicle start feature will not operate if
any of the follow occur:
The remote start system is disabled through
the DIC.
The vehicle’s key is in the ignition.
The vehicle’s hood is open.
The hazard warning ashers are on.
The check engine light is on. SeeMalfunction
Indicator Lamp on page 204.
The engine coolant temperature is too high.
The oil pressure is low.
Two remote vehicle starts have already been
used for that ignition cycle.
Vehicles that have the remote vehicle start feature
are shipped from the factory with the remote
start system enabled. The system may be enabled
or disabled through the DIC. See “REMOTE
START” underDIC Vehicle Personalization on
page 216for additional information.
Remote Start Ready
(Automatic Transaxle Only)
If your vehicle does not have the remote vehicle
start feature, it may have the remote start ready
feature. This feature allows your dealer to add the
manufacturer’s remote vehicle start feature.
If the RKE transmitter has a plus (+) symbol on the
back cover, your vehicle has the remote start ready
feature. You can lock or unlock your vehicle from
approximately 197 feet (60 m) away.
See your dealer if you would like to add the
manufacturer’s remote vehicle start feature to
your vehicle.
107

Engine Coolant Heater
Your vehicle may have this feature. In very cold
weather, 0°F (−18°C) or colder, the engine coolant
heater can provide easier starting and better fuel
economy during engine warm-up. Usually, the
coolant heater should be plugged in a minimum
of four hours prior to starting your vehicle. At
temperatures above 32°F (0°C), use of the coolant
heater is not required. Your vehicle may also have
an internal thermostat in the plug end of the cord.
This will prevent operation of the engine coolant
heater when the temperature is at or above
0°F (−18°C) as noted on the cord.
To Use the Engine Coolant Heater
1. Turn off the engine.
2. Open the hood and unwrap the electrical cord.
On the 2.4L L4 ECOTEC
®engine, the engine
coolant heater cord is located near the air
cleaner box on the passenger’s side of the
engine compartment. On the 3.5L, 3.6L and
3.9L V6 engines, the engine coolant heater
cord is located on the driver’s side around
the battery box. SeeEngine Compartment
Overview on page 318for more information
on location.3. Plug the cord into a normal, grounded
110-volt AC outlet.
{CAUTION:
Plugging the cord into an ungrounded
outlet could cause an electrical shock.
Also, the wrong kind of extension cord
could overheat and cause a re. You
could be seriously injured. Plug the cord
into a properly grounded three-prong
110-volt AC outlet. If the cord will not
reach, use a heavy-duty three-prong
extension cord rated for at least 15 amps.
4. Before starting the engine, be sure to unplug
and store the cord as it was before to keep it
away from moving engine parts. If you do
not, it could be damaged.
How long should you keep the coolant
heater plugged in? The answer depends
on the outside temperature, the kind
of oil you have, and some other things.
128

Enhanced Traction System Warning
Light...................................................... 202
Enhanced Traction System Active Light..... 202
StabiliTrak
®Not Ready Light...................... 203
StabiliTrak®Indicator Light......................... 203
Engine Coolant Temperature Gage............ 203
Malfunction Indicator Lamp........................ 204
Oil Pressure Light..................................... 207
Security Light............................................ 207
Cruise Control Light.................................. 208
Highbeam On Light................................... 208
Fuel Gage................................................. 208
Low Fuel Warning Light............................ 208
Driver Information Center (DIC).................. 209
DIC Operation and Displays...................... 209
DIC Warnings and Messages.................... 212
DIC Vehicle Personalization....................... 216Audio System(s)......................................... 219
Setting the Time for Radios without Radio
Data Systems (RDS).............................. 220
Setting the Time for Radios with Radio
Data Systems (RDS).............................. 221
Radio with CD........................................... 221
Radio with Six-Disc CD............................. 231
XM Radio Messages................................. 246
Theft-Deterrent Feature............................. 248
Audio Steering Wheel Controls.................. 248
Radio Reception........................................ 249
Care of Your CDs..................................... 250
Care of the CD Player.............................. 250
Fixed Mast Antenna.................................. 250
Backglass Antenna.................................... 250
XM™ Satellite Radio Antenna System....... 251
Section 3 Instrument Panel
162

Temperature Control:Turn the center knob
clockwise or counterclockwise to increase
or decrease the temperature inside your vehicle.
When it’s cold outside 0°F (−18°C) or lower,
use the engine coolant heater, if the vehicle has
one, to warm air faster in your vehicle. An
engine coolant heater warms the engine coolant
that is used to warm the inside of your vehicle. For
more information, seeEngine Coolant Heater on
page 128.
#(Air Conditioning):Press this button to turn
the air conditioning system on or off. When
the air conditioning button is pressed, an indicator
light comes on to indicate that the air conditioning
is activated.
The air conditioning system removes moisture from
the air, so sometimes a small amount of water drips
underneath the vehicle while it is idling or after the
engine is turned off. This is normal.
Maximum Air Conditioning
On hot days, open the windows to let hot inside
air escape; then close them. This helps to reduce
the time it takes for your vehicle to cool down.
It also helps the system to operate more efficiently.For quick cool down on hot days, do the following:
1. Select the
Cvent mode.
2. Select the highest fan speed.
3. Select
#air conditioning.
4. Select the
?recirculation mode.
5. Select the coolest temperature.
Using these settings together for long periods of
time can cause the air inside of your vehicle
to become too dry. To prevent this from
happening, after the air in your vehicle has cooled,
turn the recirculation mode off.
If your vehicle has the remote start feature, it will
turn on using the last settings selected on the
climate control before the vehicle was turned off.
The fan and air delivery knobs can be used during
remote start. The buttons will not work until the
ignition is turned on by the key.
The climate control system changes back to
manual operation when the vehicle key is
turned to ON.
184

Defogging and Defrosting
Fog on the inside of windows is a result of high
humidity (moisture) condensing on the cool window
glass. This can be minimized if the climate
control system is used properly. There are
two modes to choose from to clear fog or frost
from your windshield. Use the defog mode to clear
the windows of fog or moisture and warm the
passengers. Use the defrost mode to remove fog
or frost from the windshield more quickly.
Turn the right knob to select the defog or
defrost mode.
-(Defog):Turn the knob to this setting to
direct the air between the windshield
and the oor outlets with a small amount directed
to the side windows. This mode automatically
turns off recirculation. The air conditioning
compressor runs unless the outside temperature
is at or below freezing. The air conditioning
compressor operates although the indicator light
is not on. The air conditioning indicator
light turns off when defog is selected. If the air
conditioning button is pressed while in
defog mode, the indicator light turns on. If the
button is pressed again, the light turnsoff. The recirculation mode cannot be selected
while in the defog mode. Do not drive the
vehicle until all the windows are clear.
1(Defrost):Turn the knob to this setting to
direct most of the air to the windshield with some
air directed to the oor vents. In this mode, the
system automatically forces outside air into
the vehicle. The air conditioning compressor runs
unless the outside temperature is at or below
freezing. The air conditioning compressor operates
although the indicator light is not on. The air
conditioning indicator light turns off when defrost is
selected. If the air conditioning button is pressed
while in defrost mode, the indicator light turns on. If
the button is pressed again, the light turns off.
Recirculation cannot be selected while in the
defrost mode.
To help clear the windshield quickly, do the
following:
1. Select the defrost mode.
2. Select the highest temperature.
3. Select the highest fan speed.
185

Automatic Climate Control System
If your vehicle has this system, you can
automatically control the heating, cooling and
ventilation in your vehicle.
Automatic Operation
AUTO (Automatic):Select AUTO on both the fan
speed control and the air delivery mode control
knobs to activate the automatic system. Automatic
operation controls the inside temperature and
air delivery.Use the steps below to place the climate control
system in automatic mode:
1. Turn the fan knob and the mode knob
to AUTO.
The display shows the current set temperature.
When auto is selected, the air conditioning
operation and air inlet is automatically
controlled. The air conditioning compressor
runs when the outside temperature is over
about 40°F (4°C). The air inlet is normally set to
outside air. If it is hot outside, the air inlet can
automatically switch to recirculate inside air to
help quickly cool down your vehicle.
2. Set the temperature.
To nd your comfort setting, start with an initial
temperature setting and allow about 20 minutes
for the system to regulate. Press the up or down
arrow temperature buttons to adjust the
temperature setting as necessary. If you
choose the temperature setting of 60°F (15°C)
the system remains at the maximum cooling
setting. If you choose the temperature setting of
90°F (32°C) the system remains at the
maximum heat setting. Choosing either
maximum setting will not cause the vehicle to
heat or cool faster.
187

Be careful not to cover the sensor located on
the top of the instrument panel near the
windshield. This sensor regulates air
temperature based on sun load, and also turns
on your headlamps.
Also be careful not to cover the sensor grille
on the lower right side of the climate
control faceplate. This senses the inside
vehicle temperature needed for proper
regulation.
To avoid blowing cold air at start-up in cold
weather, the system delays turning on the fan
until warm air is available. The length of
delay depends on the engine coolant
temperature. Turning the fan knob overrides
this delay and change the fan to a selected
speed.
If your vehicle has the remote start feature, the
climate control display initially shows “AS” in place
of the temperature to indicate the remote start
has been activated. The remote start system turns
on using the last temperature selected before
the vehicle was last turned off.For best performance, turn the fan and mode
knobs to the AUTO position. The fan speed and
air delivery modes will change to achieve the best
comfort.
If the outside air temperature is below 45°F and
the air delivery mode knob is set to AUTO,
the automatic climate control system starts in the
defrost mode to clear the window.
The automatic climate control changes back to
manual operation by turning the vehicle on with
the key.
Manual Operation
You can manually adjust the air delivery mode or
fan speed.
9(Off):Select this position on the fan knob to
turn off the entire climate control system.
Outside air will still enter the vehicle, and be
directed to the oor. This direction can be changed
by changing the mode position. The temperature
can also be adjusted using either the up or
down arrow temperature buttons.
9(Fan):Turn the knob with the fan symbol to
manually adjust the fan speed.
188

Temperature Control:Press the up and down
arrows to increase or decrease the temperature
inside the vehicle.
#(Air Conditioning):Press this button to turn
the air conditioning compressor on and off. A
light above the button will come on while the air
conditioning is on.
When air conditioning is selected or in AUTO
mode, the system runs the air conditioning
automatically to cool and dehumidify the air
entering the vehicle.
On hot days, open the windows long enough to let
hot inside air escape. This reduces the time it
takes for your vehicle to cool down. Then keep the
windows closed for the air conditioner to work
its best.On cool, but sunny days while using manual
operation of the automatic system, use bi-level to
deliver warm air to the oor and cooler air to
the instrument panel outlets. To warm or cool the
air, press the temperature buttons to the desired
setting.
In AUTO mode the system will cool and dehumidify
the air inside the vehicle. Also while in AUTO
mode, the system will maximize its performance
by using recirculation as necessary.
Heating:On cold days when using manual
operation of the automatic system, choose oor
mode to deliver air to the oor outlets. To warm or
cool the air delivered, push the temperature
buttons to the desired setting.
If you want to use the automatic mode, turn the
knob to AUTO and adjust the temperature by
pressing the temperature buttons.
The heater works best if you keep the windows
closed while using it.
190

Defogging and Defrosting
You can use either defog or front defrost to clear
fog or frost from the windshield.
-(Defog):Use to clear the windows of fog or
moisture. Turn the mode knob to this position
to select this setting. This setting delivers air to the
oor and windshield outlets.
0(Defrost):Turn the mode knob to this position
to defrost the windshield. The system automatically
controls the fan speed if AUTO mode is selected.
If the outside temperature is 40°F (4°C) or
warmer, the air conditioning compressor
automatically runs to help dehumidify the air and
dry the windshield. The air conditioning indicator
light blinks three times if you try to turn off
the compressor while in this mode.
Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog from the rear window.
<(Rear):Press this button to turn the rear
window defogger on or off. An indicator light above
the button comes on to indicate that the rear
window defogger is activated.If driving below 50 mph (80 km/h), the rear window
defogger will turn off about 15 minutes after the
button is pressed. If turned on again, the defogger
will only run for about seven and one-half
minutes before turning off.
If your vehicle’s speed is maintained above
50 mph (80 km/h), the rear window defogger
remains on once the button is pressed.
If your vehicle has the remote start feature, the
rear defogger automatically turns on if it is
cold outside, but the indicator light does not come
on. When the vehicle transitions out of remote
start mode the rear defogger turns off.
Notice:Do not use a razor blade or sharp
object to clear the inside rear window. Do not
adhere anything to the defogger grid lines
in the rear glass. These actions may damage
the rear defogger. Repairs would not be
covered by your warranty.
Outlet Adjustment
Rotate the instrument panel outlets and move the
louvers on the outlets to change the direction
and amount of airow in your vehicle.
191