display PONTIAC G8 2009 Service Manual

Sport Shift Mode
The automatic transmission has a
Sport Shift Mode. When you
are in the Sport Shift Mode the
vehicle will still shift automatically.
The transmission may remain
in a gear longer than it would in the
normal driving mode based on
braking, throttle input, and vehicle
lateral acceleration. To use this
feature, move the shift lever
over from D (Drive) to the right
quadrant. The Sport Shift message
in the DIC displays. If the shift
lever is not moved forward or
rearward, the vehicle remains in
sport mode.Performance Mode Lift Foot Mode
Within Sport Shift Mode there is a
further performance feature called
Performance Mode Lift Foot (PMLF)
Mode. The feature is activated
automatically when sports oriented
driving is detected, based on
cornering and on/off throttle
application. PMLF allows the
transmission to hold the current gear
instead of upshifting when the
throttle is lifted.
Driver Shift Control (DSC)
Notice:If you drive your vehicle
at high RPMs without upshifting
while using Active Select Mode,
you could damage the vehicle.
Always upshift when necessary
while using Active Select Mode.The automatic transmission has a
DSC mode that allows gear changes
similar to a manual transmission.
To use this feature:
1. Move the shift lever over from
D (Drive) to the right quadrant.
The Sport Shift message in
the DIC displays.
2. To enter the DSC mode, press
the shift lever forward to upshift
or rearward to downshift.
The Active Select On message
in the DIC will come on.
The DIC will indicate the requested
gear range when moving the
shift lever forward or rearward.
8-8 Driving and Operating

While using the DSC mode, the
vehicle has rmer shifting and
increased performance. This can be
used for sport driving or when
climbing or descending hills, to stay
in gear longer, or to down shift
for more power or engine braking.
The transmission will only allow the
driver to shift into gears appropriate
for the vehicle speed and engine
Revolutions Per Minute (RPM). The
transmission will not automatically
shift to the next lower gear if the
engine RPM is too high.
If shifting is prevented for any
reason, the currently selected gear
will ash multiple times, indicating
that the transmission has not
shifted gears.While in the DSC mode, the
transmission automatically
downshifts when the vehicle comes
to a stop.
When accelerating the vehicle from
a stop in snowy and icy conditions,
1st, 2nd or 3rd gear starts can
be selected from a standing start.
This is useful for gentle acceleration
on slippery surfaces.
To return to Normal Shift mode,
slide the shift lever over from
the right quadrant to the left into
D (Drive). A Normal Shift message
will be displayed in the DIC.
Normal Shift Mode is recommended
for normal or freeway driving, as
it provides optimum fuel economy.Powertrain Braking
For vehicles with a 6 speed
automatic transmission, there is
an additional feature known as
Powertrain Braking. When driving
on steep descents where frequent
braking is required, the vehicle
will automatically downshift to
provide engine braking assistance.
This feature also reduces brake
temperatures and wear.
Downshifting will only occur when
the driver’s foot is applied to
the brake. Active Select Mode can
be switched on to override the
feature and gain complete control of
shifts if desired.
Driving and Operating 8-9

One to Four Shift Light
When this light comes on, you can
only shift from 1 (First) to 4 (Fourth)
instead of 1 (First) to 2 (Second).
The light will be displayed on theinstrument panel cluster and a
message will be displayed in
the Driver Information Center.
You must complete the shift into
4 (Fourth) to turn off this feature.
This helps you get the best possible
fuel economy.
After shifting to 4 (Fourth), you may
downshift to a lower gear if you
prefer.
Notice:Forcing the shift lever
into any gear except FOURTH (4)
when the 1 TO 4 SHIFT light
comes on may damage the
transmission. Shift only from
FIRST (1) to FOURTH (4) when the
light comes on.
This light will come on when:
The engine coolant temperature
is higher than 169°F (76°C),
you are going 15 to 19 mph
(24 to 31 km/h) and
you are 21 percent throttle
or less.
Parking Brake
To set the parking brake, pull up on
the parking brake handle. If the
ignition is in the ON/RUN position,
the brake system warning light
will come on. SeeBrake System
Warning Light on page 4-15. Instrument Panel
Cluster
Driver Information
Center
Driving and Operating 8-11

As you brake, the computer keeps
receiving updates on wheel speed
and controls braking pressure
accordingly.
Remember: ABS does not change
the time you need to get your
foot up to the brake pedal or always
decrease stopping distance. If
you get too close to the vehicle in
front of you, you will not have time to
apply the brakes if that vehicle
suddenly slows or stops. Always
leave enough room up ahead
to stop, even though you have ABS.
Using ABS
Do not pump the brakes. Just hold
the brake pedal down rmly and
let antilock work for you. You might
hear the antilock pump or motor
operate, and feel the brake
pedal pulsate, but this is normal.
Braking in Emergencies
With ABS, you can steer and
brake at the same time. In many
emergencies, steering can help
you more than even the very best
braking.
Electronic Stability
Program
The vehicle has the Electronic
Stability Program (ESP®) that assists
with directional control of the vehicle
in difficult driving conditions by
reducing engine power and applying
the brakes to individual wheels. This
is especially useful in slippery road
conditions. The system operates if it
senses that the rear wheels are
spinning too much, are beginning to
lose traction or if it senses that the
vehicle is not moving in its intended
direction. It turns on automatically
every time the vehicle is started.When ESP is working, this light
and the STABILITY CONTROL
ASSISTANCE message will come on
and the ESP CTRL message will be
displayed at the bottom of the DIC.
The STABILITY CONTROL
ASSISTANCE message will remain
on while the system is working
until the
3button is pressed to
display the trip computer. The
ESP CTRL message stays on at the
bottom of the DIC while the
system is working.
Driving and Operating 8-19

The system may be heard or felt
while it is working. This is normal
and does not mean there is a
problem with the vehicle.
When this light and the STABILITY
CTRL OFF message is on and
the ESP OFF message is
displayed, the system will not
limit wheel spin.
Adjust your driving accordingly.
SeeDIC Warnings and Messages
on page 4-26for more information.ESP is automatically enabled
whenever the vehicle is started.
To limit wheel spin, especially
in slippery road conditions, always
leave the system enabled. ESP
can be turned off if needed.
It is recommended to leave the
system on for normal driving
conditions, but it may be necessary
to turn the system off if the
vehicle is stuck in sand, mud, ice or
snow, and you want to rock the
vehicle to attempt to free it. It may
also be necessary to turn off
the system when driving in extreme
off-road conditions where high
wheel spin is required. SeeIf Your
Vehicle is Stuck in Sand, Mud,
Ice, or Snow on page 8-29.The ESP button is located in front of
the transmission gear selector lever.
To turn the system off or on, press
and release the ESP button.
The DIC will briey display the
appropriate message and then
return to the trip computer display.
8-20 Driving and Operating

When this light and the STABILITY
CTRL OFF message is on briey and
the ESP OFF message is displayed
at the bottom of the DIC, the system
will not limit wheel spin.
If the ESP OFF message is always
displayed at the bottom of the
DIC when the button is pressed
to turn the system on or off, the
system needs repair. Contact your
dealer/retailer.The system is on when this light
and the STABILITY CTRL ON
message is displayed briey on
the DIC.
ESP Operation
ESP limits wheel spin by reducing
engine power to the wheels and
by applying brakes to each
individual wheel as necessary.
The ESP system is enabled
automatically when the vehicle
is started, and it will activate
the STABILITY CONTROL
ASSISTANCE light and the ESP
CTRL message on the DIC if it
senses that any of the wheels are
spinning or beginning to lose traction
while driving.Notice:If the wheel(s) of one axle
are allowed to spin excessively
while the ESC/TCS, ABS and
Brake warning lights and the
SERVICE ESC and/or SERVICE
TRACTION messages are
displayed, the differential could be
damaged. The repairs would not
be covered by the vehicle
warranty. Reduce engine power
and do not spin the wheel(s)
excessively while these lights and
this message are displayed.
The traction control system may
activate on dry or rough roads or
under conditions such as heavy
acceleration while turning or
abrupt upshifts/downshifts of the
transmission. When this happens,
a noise, vibration, or a reduction
in acceleration may be noticed.
This is normal.
Adding non-dealer/non-retailer
accessories can affect the vehicle’s
performance. SeeAccessories
and Modifications on page 9-3for
more information.
Driving and Operating 8-21

Engine Oil Life System
When to Change Engine Oil
This vehicle has a computer system
that lets you know when to change
the engine oil and lter. This is
based on engine revolutions and
engine temperature, and not
on mileage. Based on driving
conditions, the mileage at which an
oil change will be indicated can
vary considerably. For the oil
life system to work properly, you
must reset the system every
time the oil is changed.
When the system has calculated
that oil life has been diminished,
it will indicate that an oil change is
necessary. The Service Engine
Oil message will be displayed.Change the oil as soon as possible
within the next 600 miles (1 000 km).
It is possible that, if you are driving
under the best conditions, the oil life
system might not indicate that an oil
change is necessary for over a year.
However, the engine oil and lter
must be changed at least once a
year and at this time the system must
be reset. Your dealer/retailer has
trained service people who will
perform this work using genuine
parts and reset the system. It is also
important to check the oil regularly
and keep it at the proper level.
If the system is ever reset
accidentally, you must change
the oil at 3,000 miles (5 000 km)
since the last oil change. Remember
to reset the oil life system whenever
the oil is changed.
How to Reset the Engine Oil
Life System
The Engine Oil Life System
calculates when to change the
engine oil and lter based on vehicle
use. Whenever the oil is changed,
reset the system so it can calculate
when the next oil change is required.
If a situation occurs where you
change the oil prior to the Service
Engine Oil message being displayed,
reset the system.
After changing the engine oil, reset
the system:
1. Turn the ignition key to ON/RUN
with the engine off.
2. Fully press and release the
accelerator pedal three times
within ve seconds.
If the Service Engine Oil
message does not appear,
the system is reset.
If the Service Engine Oil message
displays, reset the system again.
9-10 Vehicle Service and Care

If No Steam Is Coming From
The Engine Compartment
If an engine overheat warning is
displayed but no steam can be seen
or heard, the problem may not be too
serious. Sometimes the engine can
get a little too hot when the vehicle:
Climbs a long hill on a hot day.
Stops after high-speed driving.
Idles for long periods in traffic.
Tows a trailer.
If the overheat warning is displayed
with no sign of steam:
1. Turn the air off.
2. Turn the heater on to the highest
temperature and to the highest
fan speed. Open the windows as
necessary.
3. In heavy traffic, let the engine idle
in N (Neutral) while stopped. If it
is safe to do so, pull off the road,
shift to P (Park) or N (Neutral) and
let the engine idle.If the temperature overheat gage is
no longer in the overheat zone
or an overheat warning no longer
displays, the vehicle can be driven.
Continue to drive the vehicle
slow for about 10 minutes. Keep a
safe vehicle distance from the
car in front of you. If the warning
does not come back on, continue to
drive normally.
If the warning continues, pull over,
stop, and park the vehicle right away.
If there is no sign of steam, idle the
engine for three minutes while
parked. If the warning is still
displayed, turn off the engine until it
cools down. Also, see ‘‘Overheated
Engine Protection Operating Mode’’
later in this section.
Power Steering Fluid
Power Steering Fluid Level
Power steering uid is used in
all vehicles.
Check the level after the vehicle has
been driven for at least twenty
minutes so the uid is warm.
How to Check Power Steering
Fluid
To check the power steering uid,
do the following:
1. Turn the key off and let the engine
compartment cool down.
2. The power steering uid reservoir
is located on the driver side
toward the front of the engine
compartment. SeeEngine
Compartment Overview on
page 9-6.
Vehicle Service and Care 9-21

Rear Compartment
Fuse Block
The rear compartment fuse block
is located on the left side of
the trunk behind a cover.
Use the fuse puller, to remove and
replace fuses.
Fuses Usage
F1 Spare
F2 Amplier
F3 XM Radio™
F4 Radio
F5Instrument/Display/
Remote Function
Actuator/Data Link
Connection
Fuses Usage
F6 Spare
F7 Trailer
F8 OnStar™
F9 Spare
F10 ECM Battery
F11Regulated Voltage
Control Sensor
F12 Fuel Pump
Relays Usage
R1 Spare
R2 Spare
Vehicle Service and Care 9-41

The TPMS operates on a radio
frequency and complies with
RSS-210 of Industry and Science
Canada. Operation is subject to the
following two conditions:
1. This device may not cause
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation of the device.
Changes or modications to this
system by other than an authorized
service facility could void
authorization to use this equipment.Tire Pressure Monitor
Operation
The Tire Pressure Monitor System
(TPMS) is designed to warn the
driver when a low tire pressure
condition exists. TPMS sensors are
mounted onto each tire and
wheel assembly, excluding the
spare tire and wheel assembly. The
TPMS sensors monitor the air
pressure in the vehicle’s tires and
transmit the tire pressure readings to
a receiver located in the vehicle.
When a low tire pressure condition
is detected, the TPMS turns on the
7
low tire pressure warning light.
At the same time a message to
check the pressure in a specic tire
appears on the Driver Information
Center (DIC) display. The low tire
pressure warning light and the DIC
warning message come on at each
ignition cycle until the tires are
inated to the correct ination
pressure. Using the DIC, tire
pressure levels can be viewed bythe driver. For additional information
and details about the DIC operation
and displays seeDIC Operation and
Displays on page 4-22andDIC
Warnings and Messages on
page 4-26.
The low tire pressure warning light
may come on in cool weather
when the vehicle is rst started, and
then turn off as you start to drive.
This could be an early indicator that
the air pressure in the tire(s) are
getting low and need to be inated
to the proper pressure.
A Tire and Loading Information label
shows the size of the vehicle’s
original equipment tires and the
correct ination pressure for the
vehicle’s tires when they are cold.
SeeLoading the Vehicle on
page 8-30, for an example of the Tire
and Loading Information label and its
location on the vehicle. Also see
Inflation - Tire Pressure on
page 9-49.
9-54 Vehicle Service and Care