lock PONTIAC PONTIAC 1995 Repair Manual

Using the wheel wrench, loosen all the wheel nuts.
Don’t remove them yet.
Turn the jack handle clockwise to raise the jack lift head
a few inches.
Position the jack under the
vehicle and raise the jack
lift head until it fits firmly
into the notch in
the
vehicle’s frame nearest the
flat tire.
5-26
ProCarManuals.com

Put the compact spare tire near you.
I
I NOTICE:
the vehicle to fall off the jack. Be sure to fit the
jack lift head into the
proper location before
raising your vehicle.
Raise the vehicle by turning the jack handle clockwise.
Raise the vehicle far enough off the ground for the spare
tire to fit under the vehicle. Remove all wheel nuts and
take off the flat tire.
5-27 ProCarManuals.com

Lower the vehicle by turning the jack handle
counterclockwise, Lower
the jack completely.
Tighten the wheel nuts
firmly in a crisscross
sequence as shown.
5-29
ProCarManuals.com

Filling Your Tank The cap is behind a hinged door on the left side of your
vehicle.
While refueling, hang the cap inside the fuel
door.
To take off the cap, turn it slowly to the left
(counterclockwise).
6-5
ProCarManuals.com

6
4. Lift the plastic locking tabs on the electrical
connector and pull the connector from the headlamp
socket.
Note which way the socket is pointing before
you disconnect it. You’ll need to install the
new headlamp
so the socket points in the same
direction.
5. Set the headlamp assembly on a work surface with
the lens facing you.
6. Remove the Torx@
screws at the end
of the
aiming ring. The aiming
ring will swing open like
a gate.
7. Remove the aiming ring. Place it face down on the
work surface with the aim indicator
up.
8. Check that the number on the new headlamp
matches the number on the headlamp being replaced.
The letter on the headlamp
(U or L) must also match.
9. Put the new headlamp in position.
Make sure the socket points in the same direction
as
it did with the old headlamp.
6-33
ProCarManuals.com

10. Insert the tabs on the
aiming ring into the
11. Holding the
aiming ring closed, insert the screws at
the end of the ring. Tighten -the screws until the
aiming ring touches the plastic nuts on both the top
and bottom.
0 Da not overtighten.
12. Do not damage the vertical aiming bubble.
13. Plug the electrical connector into the headlamp
socket. Make sure the locking tabs snap onto
the
socket.
14. Put the headlamp assembly
in position. Make sure
the two guide tabs drop into their holes in the
headlamp support panel.
guide tabs are still in place before tightening the
screws.
15. Tighten the two bottom
screws. Make sure the
16. Insert the top screw and tighten it.
17. Close the headlamp panel.
6-34
ProCarManuals.com

Headlamps @-Door Models)
1. Open the headlamp panel.
2. Turn the socket
counterclockwise until
it pops loose from the
housing.
3.
4.
5.
6.
7.
Pull out the bulb socket.
Lift the plastic locking tab on the electrical
connector and pull the connector
from the bulb
socket.
Snap the electrical connector into
a new bulb socket.
Replace the bulb socket into the housing
and turn
clockwise.
Close the headlamp panel.
6-35
ProCarManuals.com

5. Pull the lamp bar housing away from the body of the
vehicle.
K uw
6. Squeeze the tab on the socket and turn the socket
counterclockwise.
7. Pull out the socket.
8. Pull the bulb out of the socket.
9. Push in a new bulb.
10. Replace the socket into the lamp bar assembly and
11. Replace the lamp
bar assembly to the body of the
turn clockwise.
vehicle.
12. Install the wing nuts.
13. Put the covers back and install the pins.
6-37 ProCarManuals.com

Front Sidemarker (&Door Models) Front Turn Signal (2-Door Models)
1.
2.
Remove the screws and
pull the sidemarker
housing forward.
Turn the socket
counterclockwise and
pull the socket out
of the
housing.
3.
4.
5.
6.
7.
Pull the bulb out of the socket.
fish
in a new bulb.
Replace the socket into the housing
and turn
clockwise.
Replace the housing to the vehicle.
Install the screws-
45 -3
L A
1. Remove the pins from the cover above the turn
signal lamps.
6-38 ProCarManuals.com

3.
4.
5.
6.
7.
Turn the socket
counterclockwise 1/6-tum until it feels
loose.
Pull out~the socket.
Pull the bulb out
of the socket.
Push
in a new bulb.
Replace the socket into the housing and
turn
clockwise until it snaps in place.
Replace the cover and pins.
Front Turn Signal (4-Door Models)
)I 1. Remove the screws and
3. Pull out the bulb socket.
2.
pull the turn signal
housing forward.
Turn the bulb socket counterclockwise until
it pops loose from the
housing.
4. Lift the plastic locking tab on the electrical
connector and pull the connector from the bulb
socket.
5. Snap the electrical connector into a new bulb socket.
6. Replace the bulb socket into the housing and turn
clockxvise.
7. Replace the housing to the vehicle.
8. Install the screws.
6-39 ProCarManuals.com