warning lights PORSCHE 911 CARRERA 2006 5.G Owner's Manual
[x] Cancel search | Manufacturer: PORSCHE, Model Year: 2006, Model line: 911 CARRERA, Model: PORSCHE 911 CARRERA 2006 5.GPages: 308, PDF Size: 3.69 MB
Page 96 of 308

96
Controls, Instruments With the engine warmed up and running at a speed 
of 5000 rpm, the engine oil pressure should be 
approx. 3.5 bar.If oil pressure drops abruptly and a message 
is displayed on the on-board computer when 
the engine is running on or when driving:
fStop immediately in a suitable place.
fSwitch off the engine.
fCheck oil level. 
Please observe the chapter “OIL DISPLAY AND 
MEASUREMENT OF THE ENGINE OIL LEVEL” 
on Page 118.
Please observe the chapter “ENGINE OIL 
LEVEL” on Page 201.
fAdd engine oil if necessary.
 Caution!
Risk of engine damage.
fDo not continue driving if there is an obvious oil 
leak.
fDo not continue driving if the warning lights 
come on even though oil level is correct.
fHave the fault remedied at the nearest authorized Porsche dealer.If the battery voltage drops abruptly, a warning 
message will be displayed by the on-board compu-
ter.
If the warning is displayed by the on-board 
computer while the engine is running or while 
driving: 
fStop the car in a safe place and stop the 
engine. 
Possible causes 
– Defect in the battery charging system. 
– Broken drive belt. 
 Warning!
Risk of an accident and risk of engine dam-
age.
A broken drive belt means there is no power 
assistance to the steering (more effort is re-
quired to steer) and coolant pump function 
will stop. 
fDo not continue driving. 
fHave the fault remedied at the nearest author-ized Porsche dealer. 
Engine Oil Pressure 
Battery 
Page 97 of 308

Controls, Instruments
97
The warning light in the instrument panel comes 
on when the ignition is first turned on and remains 
on briefly as a bulb check. If the light does not 
come on, have the bulb replaced promptly. 
If the warning lights in the instrument panel and on-
board computer come on and remain on while 
driving, it suggests: 
– a potential engine control problem and the 
need for system service or 
– an improperly fastened tank cap or 
– refuelling with engine running.
Although the vehicle is usually driveable and will 
not require towing, see your dealer for service as 
soon as possible. 
 Caution!
If the Check engine light in the instrument 
panel is flashing, severe catalytic converter 
damage and power loss will soon occur.
Prolonged driving with the Check engine light 
on could cause damage to the emission con-
trol system. It also could affect fuel economy 
and driveability. 
fHave the fault remedied at the nearest author-ized Porsche dealer immediately. The central warning light on the instrument panel 
lights up if there are warning messages in the 
INFO menu.
The messages can be called in the on-board 
computer INFO menu:
fPlease observe the chapter “INFO WARNING 
MESSAGES” on Page 102.
The warning light on the instrument panel lights 
up:
– if the handbrake is on,
– if the brake fluid level is low,
– if the brake pads have reached the wear limit,
– if the brake circuit division is defective.
Additionally, a warning is displayed by the on-
board computer.
fPlease observe the chapter “WARNINGS ON 
THE INSTRUMENT PANEL AND THE ON-
BOARD COMPUTER” on Page 122.
Check Engine 
Warning Light 
Central warning light
Brake warning light USA
Brake warning light Canada 
Page 116 of 308

116
Controls, Instruments The warning light in the speedometer lights up:
– When a loss in pressure has been detected
– If the tire pressure monitoring is faulty
– When learning newly mounted wheels/wheel 
sensors, as long as the vehicle’s own wheels 
have not yet been recognized.
The tire pressure warning light in the instrument 
panel goes out only when the cause of the fault 
has been rectified.
No monitoringIn the event of faults the tire pressure monitoring 
cannot monitor the tire pressure. 
The warning light on the instrument panel lights up 
and a corresponding message appears on the 
on-board computer. 
Monitoring is not active when:
– the tire pressure monitoring is faulty,
– wheel transmitters for the tire pressure 
monitoring are missing,
– temporarily after changing a wheel (learning 
phase),
– more than four wheel transmitters are 
detected,
– there is external interference by other radio 
sources, e.g. wireless headphones,
– tire temperatures are too high.
fPlease observe the chapter “WARNINGS ON 
THE INSTRUMENT PANEL AND THE ON-
BOARD COMPUTER” on Page 122.
Pressure increase as the result of 
temperature increaseA Tire pressure
B Tire temperature
C Tire pressures for cold tires
D Tire pressure for hot tires
E Pressure increase as the result of temperature 
increase
F Pressure drop in faulty/leaking tires
1. Required-pressure line
2. Warning stage 1 (from –3 to –6 psi
(–0.2 bar to –0.4 bar))
3. Warning stage 2 (from –6 psi (–0.4 bar))
Warning light 
Page 122 of 308

122
Controls, Instruments
Warnings on the instrument panel and the on-board computerIf a warning message appears, always refer to the corresponding chapters in the Owner’s Manual.
Warning messages are issued only if all measurement preconditions are met. Therefore, check all fluid levels regularly – 
in particular, always check the engine oil level after refuelling.
Instrument 
panelOn-board 
computerText display on on-board 
computerMeaning/measure
Seat belt Driver and passengers must fasten their seat 
belts.
Handbrake Handbrake is still on.
Ignition key 
not removed
Replace battery 
in ignition keyReplace the remote-control battery.
Ignition lock faulty, 
please go to workshopHave the fault remedied at an authorized 
Porsche dealer.
Ignition lock faulty, 
visit workshop nowHave the fault remedied at an authorized 
Porsche dealer.
Relieve  steering Relieve the steering  l o c k  b y  m o v i n g  t h e  s t e e r i n g  
wheel to the left or right.
Steering locked The steering wheel lock remains engaged. 
Have the fault remedied at an authorized 
Porsche dealer.
Lights on
Parking light on 
Page 123 of 308

Controls, Instruments
123
Check left/right dipped beam (low 
beam)
also applies to: 
front side lights, direction indicator, 
high beam, fog lights, side indicator 
light, brake light, tail light, rear fog 
light, reversing light, raised brake 
light, side markerThe reported light is faulty. Check bulb.
Have the fault remedied at an authorized 
Porsche dealer.
Daytime 
driving lights offDaytime driving lights switch off when the engi-
ne is shut off. Switch on lights if necessary.
Headlight beam 
adjustment faultyHave the fault remedied at an authorized 
Porsche dealer.
Front lid not closed Close luggage compartment lid properly.
Rear lid not closed Close engine compartment lid properly.
Lid opener front
faultyLuggage compartment lid release is faulty.
Have the fault remedied at an authorized 
Porsche dealer.
Rain sensor faulty Have the fault remedied at an authorized 
Porsche dealer.
Refill washer fluid
LIMIT
Cannot be accepted 
with vehicle stoppedThe current speed can only be accepted for the 
acoustic warning signal when the vehicle is in 
motion.
LIMIT
30Selected speed limit (e.g. 30 mph) for the 
acoustic warning signal has been exceeded. 
Adjust your speed if necessary.
Instrument 
panelOn-board 
computerText display on on-board 
computerMeaning/measure 
Page 133 of 308

Controls, Instruments
133
Windshield Wiper / Washer Lever 
 Warning!
Danger of injury when the windshield wipers 
operate unintentionally. 
Risk of damage to the windshield and wiper 
system. 
fAvoid running the wiper blades over a dry wind-
shield to prevent scratching the glass. Spray 
washer fluid on the windshield first. 
A scratched windshield will reduce visibility. 
fAlways loosen wiper blades from frozen glass 
before operating wipers to prevent damage to 
the wiper motor or blades. fAlways switch off windshield wipers in car 
wash to prevent them wiping unintentionally 
(intermittent or sensor operation). 
fAlways switch off windshield wipers before 
cleaning the windshield to avoid unintentional 
operation (intermittent or sensor operation). 
fDo not operate the headlight washer in car 
washes. 
fDo not operate headlight washer when it is 
frozen. 
Front wiper and headlight washer system0  –  Windshield wipers off
1  –  Rain sensor operation for front 
windshield wipers
fMove wiper lever upwards to the first click.
Please observe the chapter “RAIN SENSOR” on 
Page 135.
2  –  Windshield wipers slow
fMove wiper lever upwards to the second click.
3  –  Windshield wipers fast 
fMove wiper lever upwards to the third click.
4  –  Front windshield wiper – one-touch oper-
ation:
fMove wiper lever downwards. The front wind-
shield wipers wipe once.5  –  Windshield wipers and washer system:
fPull wiper lever towards the steering wheel. 
The washer system sprays and wipes while the 
lever is pulled towards the steering wheel. 
When the wiper lever is released, a few drying 
wipes are executed. 
A - Headlight washer (Vehicles with Bi-Xenon 
headlights):
The washer sprays only while low beam or high 
beam is switched on.
fBriefly push button A to operate headlight 
washer system.
fIf heavily soiled, repeat wash.
The headlight washer system automatically sprays 
once for every ten times the front windshield 
washer system is operated.
Note
The windshield washer nozzles are heated 
when the ignition is on, as a precaution against 
freezing.  
Page 139 of 308

Controls, Instruments
139
Setting temperaturefPress button H upwards or downwards 
respectively.
To suit personal comfort, the interior temperature 
can be adjusted between 61°F and 85°F/16 and 
29.5°C. 
Recommendation: 72°F/22°C.
If “LO” or “HI” appears on the display, the system 
is operating at maximum cooling or heating pow-
er.
Automatic control is no longer active.
Note
If the preselected temperature is changed, the 
blower speed can increase automatically in auto-
matic mode.
The desired temperature is reached more quickly 
this way.
Sensors
To avoid affecting the performance of the air-con-
ditioning system:
fDo not cover the sun sensor on the instrument 
panel or the temperature sensor D.fPress button B (switch on or off).
The windshield is defogged or defrosted as 
quickly as possible.
Air flows to the windshield only.
The light-emitting diode in the button lights up.
ECO – switching compressor for air-
conditioning system on and offThe air-conditioning compressor switches off 
automatically at temperatures below approx. 
37°F/3°C and cannot be switched on, even 
manually.
Whenever outside temperatures exceed approx. 
37°F/3°C, the air-conditioning compressor is 
always switched on in automatic mode.
The compressor can be switched off to save fuel, 
but control comfort is then limited:
fPress ECO button E.
The compressor is switched off.
The light-emitting diode in the button lights up.
fIf the interior temperature is too high, switch 
compressor back on or press AUTO button.
To dry incoming air in damp weather, do not 
switch off the air-conditioning compressor. 
This prevents fogging of windows.
Defrosting the windshield
fPress button M upwards or downwards 
respectively.
The preset blower speed is increased or 
decreased.
The speed stages are indicated by a bar display.
If the button is pressed downwards at the lowest 
blower stage, the blower and automatic control 
are switched off. “OFF” will appear on the display 
field.
Pressing the button upwards or pressing the 
AUTO button switches the blower and automatic 
control back on again.
 Warning!
Risk of accident due to impaired vision. 
In recirculating-air setting, the windows may 
fog up.
fOnly select recirculating-air setting for short 
periods.
fIf the windows fog up, switch recirculating-air 
setting off immediately by pressing the 
circulating-air button again and select the “Defrost windshield” function.
f   f   f
Adjusting blower speed
Recirculating-air setting 
Page 152 of 308

152
Controls, Instruments
Trunk EntrapmentYour vehicle is equipped with an internal trunk 
release mechanism. 
A person trapped in the luggage compartment 
can release the lid from the inside using unlocking 
handle A.
The handle A is fluorescent and glows in the dark. A warning message in the on-board computer 
lights up when unlocking handle A is operated.
fStop the vehicle immediately when the warning 
lights light up.
fCheck the luggage compartment.
fClose the lid.Function with vehicle stationary 
If the luggage compartment lid is unlocked with 
unlocking handle A, the lid can be opened from the 
inside immediately. 
Function with vehicle in motion 
If the luggage compartment lid is unlocked with 
unlocking handle A when a speed of 2 
mph 
(3 km/h
) is exceeded, the warning message in the 
on-board computer lights up.
At the same time, the lid is unlocked and the latch 
striker pops into the catch-hook position.
Warning light  
Page 153 of 308

Controls, Instruments
153
 Danger!
Risk of accident. 
If the warning message in the on-board com-
puter lights up when the vehicle is in motion, 
the lid may impact in front of the windshield 
and can tear off. 
You can lose control of the vehicle.
fStop the vehicle immediately when the warning 
message lights up.
fCheck the luggage compartment.
fClose the lid.Note
The lid cannot be opened from the inside if the bat-
tery is disconnected or empty.
Safety reasons require that you unscrew the 
latch striker of the lid lock if you plan to put 
the vehicle out of operation for an extended 
period.
Please consult your authorized Porsche dealer. 
They will advise you about the necessary meas-
ures.
Note
fWhen loading the luggage compartment, make 
sure that items of luggage or other objects 
cannot become caught on handle A.
This could cause the luggage compartment to 
open unintentionally. 
Page 155 of 308

Controls, Instruments
155
1, 2, 3 - Programmable buttons
A- Light-emitting diode for status identificationHomeLinkThe programmable HomeLink replaces up to three 
original hand-held transmitters used to operate 
various devices (e.g. garage door, gate to the 
property, alarm system).
You can program buttons 1 to 3 with a frequency 
of an original handheld transmitter.
 Warning!
Risk of accident when using the HomeLink if 
persons, animals or objects are within the 
range of movement of the equipment that is 
being operated.
fWhen using the HomeLink, ensure that no 
persons, animals or objects are within the 
range of movement of the equipment that is 
being operated.
fObserve the safety notes for the original hand-held transmitter.
Preconditions for operating and 
programming the HomeLink:
– Ignition is switched on.
– Fog lights are switched off.
To operate the respective device:
fPress the appropriate button (1, 2 or 3).
Light-emitting diode A lights up during signal 
transfer.Note on operation
fAlways use the HomeLink opener in the 
direction of travel.
Otherwise, range restrictions cannot be ruled 
out.
fBefore selling the vehicle, delete the 
programmed signals of the HomeLink. 
fPlease read the instructions for the original 
hand-held transmitter to find out whether the 
original transmitter is equipped with fixed or 
changeable code.