key PORSCHE 911 TURBO 2014 6.G Workshop Manual

Storage, Luggage Compartment and Roof Transport System 201
1.Lift seals F on the roof rail using the hook of the torque wrench and pull them out. 2. Fold out all eight rotary holders G using the hook of the torque wrench. 3. Unlock cover flaps H using the key and fold upwards as far as possible.4. Ensure that the carriers are fitted in accordance with the stickers on the underside of the carriers.
14_991_Turbo_21.book Seite 201 Mittwoch, 9. April 2014 2:19 14

210 Parking
Swivelling Down Mirror Glass as
Parking Aid
When reverse gear is engaged, the mirror on the passenger’s side swivels down slightly to show the curb area.
Preconditions
– The ignition must be switched on. – The function must be activated on the multi-function display.
For further information on setting the parking aid:fPlease see the chapter “ADJUSTING REVERSING OPTIONS” on page 122.
Swivelling down mirror glass manually
If the function was deactivated on the multi-function display, the exterior mirror on the passenger’s side can also be swiveled down manually.1. Engage reverse gear. The indicator light B on the selection button A for adjusting the exterior mirror on the driver’s side lights up.2. Press the selection button D for adjusting the exterior mirror on the passenger’s side.The mirror on the passenger’s side swivels down.
Information
The position of the automatically lowered mirror glass can be changed as required using the adjustment button C. On vehicles with memory package, the setting is stored on the car key or the person buttons on the driver’s side.
Moving mirror to its initial position
The mirror swivels back to its initial position: – after a certain time delay, if the vehicle is shifted out of reverse gear, or – immediately, if the vehicle reaches a speed of more than 9 mph (15 km/h).
The exterior mirror on the passenger’s side can also be moved to its initial position manually.fPress the selection button A for the exterior mirror on the driver’s side.
14_991_Turbo_21.book Seite 210 Mittwoch, 9. April 2014 2:19 14

Parking 211
Garage Door Opener HomeLink®
(Universal Remote Control)
With the HomeLink® of your Porsche, a wide range of remote-controlled equipment (e.g. garage door/gate to your property, security systems, house lights) can be activated from inside the vehicle.
The HomeLink® system replaces up to three different original remote controls. The signal for a remote control can be assigned to one of the three memory buttons I, II and III on the overhead operating console keypad. The respective equipment can then be operated using the programmed memory button.
Transmission of the signal is indicated by the indicator light in the button II.
Information
fPlease read the instructions for the original remote control.fInformation on the compatibility of your vehicle’s HomeLink® system with the original remote control can be obtained from your authorized Porsche dealer, on the HomeLink® website (www.homelink.com) or by calling the free HomeLink® hotline (1-800-355-3515).
When opening and closing the equipment being operated, parts of the body could become trapped or crushed.fWhen using the garage door opener, make sure that no persons or animals are within the range of movement of the equipment that is being operated.fObserve the safety notes for the original remote control.
Information
fWhen the button is pressed, the transmitter unit sends the signal forward in direction of travel.Always align the vehicle with the receiver.Otherwise, range restrictions cannot be ruled out.fBefore selling the vehicle, delete the programmed signals for the garage door opener on the keypad. fIf the equipment cannot be operated after the initial programming, check whether the original remote control has fixed or changeable code.To find this out, read the instructions for the original remote control.
Garage Door Opener Use
WARNINGh
14_991_Turbo_21.book Seite 211 Mittwoch, 9. April 2014 2:19 14

212 Parking
Operating the garage door opener
The ignition must be switched on.fPress and hold the corresponding HomeLink® button on the overhead operating console keypad.The indicator light A lights up during signal transmission.
Programming garage door opener: Deleting and storing signals
The HomeLink® system is programmed on the overhead operating console and in direct proximity to the vehicle’s radiator grille.
Preconditions
In order to delete programmed signals and store garage door opener signals,– the ignition must be switched on,– the turn signals must be off and – the engine must be off.
When using the garage door opener, the vehicle must be within the range of the receiver.
Deleting programmed signals from the buttons
This process clears all of the HomeLink® programming. It is not possible to individually clear the programmed buttons.Do not repeat this process if you want to assign additional signals to the buttons.fKeep the two outer buttons I and III on the overhead operating console keypad pressed for approx. 20 seconds until the indicator light A on button II starts to flash quickly.fRelease the buttons.
The HomeLink® buttons are cleared and can be reprogrammed.
Assigning garage door opener signal to key with fixed code system
On the overhead operating console: 1. Switch on ignition. 2. The standard factory-set codes must be deleted before programming for the first time . 3. Press and hold the desired button on the overhead operating console keypad until the indicator light A on button II starts to flash slowly.You now have 5 minutes to teach the button.4. Stand in front of the vehicle with the original remote control of the system to be programmed.
14_991_Turbo_21.book Seite 212 Mittwoch, 9. April 2014 2:19 14

Parking 213
In front of the vehicle: 5. Hold the original remote control approx. 8 in. (20 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A on the overhead operating console starts flashing quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
6. The turn signal lights will flash once when the 5 minute teaching readiness period has elapsed.Repeat steps 3 to 5.7. Repeat steps 3 to 5 to assign further signals to the remaining buttons.
Assigning garage door opener signal to button with changeable code system
With some systems, a changeable code also needs to be programmed for the HomeLink® system. A second person makes programming easier.
Identifying the changeable code
fPress and hold the previously programmed HomeLink® button.
If the indicator light A on button II in the overhead operating console starts to flash quickly and lights up continuously after approx. 2 seconds, it means that the equipment has a changeable code system.fInformation on synchronization can also be found in the operating instructions for the system to be programmed.
Assigning garage door opener signal to key
fPark the vehicle within the range of the remote- controlled equipment.
On the overhead operating console: 1. Switch on ignition. 2. The standard factory-set codes must be deleted before programming for the first time.
For information on deleting the factory-set codes:fPlease see the chapter “PROGRAMMING GARAGE DOOR OPENER: DELETING AND STORING SIGNALS” on page 212.3. Press and hold the desired button on the overhead operating console keypad until the indicator light A on button II starts to flash slowly.You now have 5 minutes to teach the button.4. Stand in front of the vehicle with the original remote control of the system to be programmed.
In front of the vehicle: 5. Hold the original remote control approx. 12 in. (30 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A on the overhead operating console starts flashing quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
14_991_Turbo_21.book Seite 213 Mittwoch, 9. April 2014 2:19 14

214 Parking
6.The turn signal lights will flash once when the 5 minute teaching readiness period has elapsed.Repeat steps 3 to 5.7. Repeat steps 3 to 5 to assign further signals to the remaining buttons. 8. Locate the programming button on the receiver of the equipment to be programmed, e.g. on the motor unit of the garage door opener.
Synchronizing the system
9. Activating the motor unit: Press the programming button on the receiver of the garage door opener.You then usually have approx. 30 seconds to initiate step 10 (a setting indicator is usually activated on the motor unit).10. Programming on the overhead operating console:Press the button you selected in step 3 three times on the overhead operating console keypad (you must press the button on the keypad several times to complete the setting process for some devices).11. Repeat steps 3 to 10 to assign signals to the other buttons.12. After completing programming on the overhead operating console, the system should recognize the HomeLink® signal and launch as soon as the memory button is pressed when the ignition is switched on.
Reprogramming an individual button on the keypad
A HomeLink® button can be individually reprogrammed without deleting the rest of the button assignments.
On the overhead operating console: 1. Switch on ignition. 2. Press and hold the button to be programmed on the overhead operating console keypad (approx. 20 seconds), until indicator light A on button II flashes slowly. You now have 5 minutes to teach the button.3. Stand in front of the vehicle with the original remote control of the system to be programmed.
In front of the vehicle: 4. Hold the original remote control approx. 12 in. (30 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A in the overhead operating console starts to flash quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
5. The turn signal lights will flash once when the 5-minute teaching readiness period has elapsed.Repeat steps 1 to 4.6. Repeat steps 1 to 4 to assign further signals to the other buttons.
Information
fPlease consult an authorized Porsche dealer if you have not been able to successfully assign signals to the buttons even though you have carefully followed the instructions in this section and the operating instructions for the original remote control. Your authorized Porsche dealer has a list of all garage door opener signals that can be adapted.fMake sure that the battery in the remote control for the garage door opener is new. If the battery voltage is inadequate, faults may occur in signal transmission. The system in the vehicle then learns the wrong code, which will not be recognized reliably by the garage door opening mechanism.
14_991_Turbo_21.book Seite 214 Mittwoch, 9. April 2014 2:19 14

216 Alarm System and Theft Protection
Alarm System and Passenger
Compartment Monitoring
FCC Numbers :
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation of this device is subject to the following two conditions:1. This device may not cause harmful interference, and 2. this device must accept any interference received including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modification could void the user's authority to operate the equipment.
The alarm system monitors the following alarm contacts:– Alarm contacts in doors, luggage compartment lid, engine compartment lid and headlights.– Interior surveillance: Movement in the interior when the vehicle is locked, e.g. attempted theft after breaking a window.– Inclination sensor country-specific equipment: inclination of the vehicle (e.g. when attempting to tow).
If one of these alarm contacts is interrupted, the alarm horn sounds for approx. 30 seconds and the emergency flasher flashes.After 5 seconds of interruption, the alarm is triggered again. This cycle is repeated up to ten times.
Switching on
fThe alarm system is activated when the vehicle is locked.
Switching off
fThe alarm system is deactivated when the vehicle is unlocked.
Information
fIf you unlock the vehicle with the emergency key in the door lock, you must switch the ignition on (ignition lock position 1) within 10 seconds of opening the door in order to prevent the alarm system from being triggered.
Information
If button on the car key is pressed and a door or the luggage compartment lid is not opened, the vehicle is locked again automatically after 30 seconds.
Switching off the alarm system if it is triggered
fUnlock vehicle or switch on ignition.
Switching off interior surveillance and inclination sensor
If people or animals are remaining in the locked vehicle or the vehicle is being transported on, e.g. a train or ship, the interior surveillance system and inclination sensor must be switched off temporarily.fInform any persons remaining in the vehicle that the alarm system will be triggered if the door is opened.
Using the car key
fQuickly press button on the car key twice within 2 seconds.The emergency flasher flashes slowly once.The doors are locked, but can be opened from inside.
USA: KR55WK50138
Canada: 7812D-5WK50138
14_991_Turbo_21.book Seite 216 Mittwoch, 9. April 2014 2:19 14

Alarm System and Theft Protection 217
On vehicles with Porsche Entry & Drive
fQuickly press button A in the door handle twice within 2 seconds. The emergency flasher flashes slowly once.The doors are locked, but can be opened from inside.
Information
The interior surveillance system and inclination sensor remain switched off if:– The interior surveillance system and inclination sensor were switched off when you last locked the vehicleandIf button A was pressed and a door or the luggage compartment lid was not opened.
Function indication
On vehicles without Porsche Entry & Drive, the locking condition of the vehicle is indicated by the indicator lights in the central locking button flashing at different frequencies.The indicator lights go out when the vehicle is unlocked.
On vehicles with Porsche Entry & Drive, the locking condition of the vehicle is indicated by the indicator lights in the doors flashing at different frequencies.
Alarm system is activated
– The indicator lights flash quickly twice when the vehicle is being locked, then flash normally.
Alarm system is activated, interior surveillance and inclination sensor are switched off
– The indicator lights flash quickly while you are locking the vehicle, go out for 10 seconds and then flash normally.
Faults in the central locking system and alarm system
The indicator lights come on for 10 seconds, flash at double speed for 20 seconds and then flash normally.
Avoiding false alarms
fIf people or animals are remaining in the locked vehicle or the vehicle is being transported on a train or ship, for example, the interior surveillance system and inclination sensor must be switched off temporarily.fAlways close the sunroof and all door windows.
Immobilizer
There is a transponder (an electronic component), containing a stored code, in each key. Before the ignition is switched on, the ignition lock checks the code.
The immobilizer can be deactivated and the engine started using an authorized ignition key only.
Theft Protection
When leaving the vehicle, always:fClose the windows.fClose the sunroof.fClose the Convertible top (Cabriolet).fActivate the electric parking brake.fRemove the ignition key (or switch ignition off on vehicles with Porsche Entry & Drive).fClose the glove box.fClose all storage compartments.fRemove valuables, vehicle registration documents, telephone and house keys from the vehicle.fClose the luggage compartment lid.fClose the engine compartment lid.fLock the doors.
14_991_Turbo_21.book Seite 217 Mittwoch, 9. April 2014 2:19 14

220 Maintenance and Car Care
If the vehicle is not secured, or incorrectly secured, during repair work, it could move unexpectedly or fall from the car jack or car lift.fBe alert and cautious around the engine at all times while it is running. If you have to work on the engine while it is running, always apply the electric parking brake and put the PDK selector lever in position P or N.fAlways support your car with safety stands if it is necessary to work under the car. The jack supplied with the car is not adequate for this purpose.Switch off level control of air suspension and height adjustment.Please see the chapter “RAISING THE VEHICLE WITH A LIFTING PLATFORM, TROLLEY JACK OR STANDARD JACK” on page 254.fJack up the vehicle only at the specified jacking points on the underside of the vehicle.fNever start the engine when the vehicle is jacked or lifted up. Vibration from the engine could cause the vehicle to fall.fWhen working under the car without safety stands but with the wheels on the ground, make sure the car is on level ground, the wheels are blocked, and that the engine cannot be started.Withdraw ignition keys (switch ignition off in vehicles that have Porsche Entry & Drive).
Information
fIncomplete or improper servicing may cause problems in the operation of the car. If in doubt about any servicing, have it done by your authorized Porsche dealer.Improper maintenance during the warranty period may affect your Porsche warranty coverage.fSome countries require additional tools and special spare parts to be carried in your vehicle. Please make enquiries before driving abroad.
Technical Modifications
fModifications may be carried out on your vehicle only if approved by Porsche.This ensures that your Porsche will remain reliable and safe to drive, and that it will not be damaged as a result of the modifications.Your authorized Porsche dealer will be pleased to advise you.
Information
fOnly use genuine Porsche spare parts for your vehicle or spare parts of similar quality which have been manufactured according to the specifications and production requirements of Porsche. These parts are available from your authorized Porsche dealer. Safety-related accessories should only be used if they are from the Porsche Tequipment range or are tested and approved by Porsche. Your authorized Porsche dealer will be pleased to advise you and answer any questions you may have.However, the use of other parts or accessories may adversely affect the safety of your vehicle, and Porsche can take no responsibility for any loss or damage caused by their use.Even if the supplier of other accessories or parts is a recognized supplier, the safety of your vehicle may still be affected if such items are installed.Due to the large variety of products offered in the accessory market, it is not possible for Porsche to inspect and approve every one.fIn addition, please note that the use of replacement parts that are not genuine Porsche parts or approved parts, or the use of accessories not approved by Porsche may also detrimentally affect your vehicle warranty.fCheck your vehicle regularly for signs of damage. Damaged or missing aerodynamic components, such as spoilers or underbody panels, impair vehicle handling and must therefore be replaced immediately.
Failure to Secure VehicleWARNINGh
14_991_Turbo_21.book Seite 220 Mittwoch, 9. April 2014 2:19 14

232 Maintenance and Car Care
High-pressure cleaning equipment, steam cleaners
Risk of damage as a result of using high-pressure cleaning equipment, steam cleaners or similar.
High-pressure cleaning equipment, steam cleaners or similar can damage the following components:– Convertible top– Tires– Logos, emblems– Painted surfaces– Alternator– Electrical components and plug connections in the engine compartment– ParkAssist sensors– Radar sensor for adaptive cruise control– Reversing camerafAlways read the operating instructions provided by the equipment manufacturer.fAlways cover the lid of the brake fluid reservoir prior to cleaning. Never point the cleaning jet directly at the lid.fWhen cleaning with a flat-jet nozzle or a so-called “dirt blaster”, maintain a minimum distance of 20 in. (50 cm).fNever use high-pressure cleaning equipment or steam cleaners with a round-jet nozzle.A high-pressure cleaning device or steam cleaner fitted with a round nozzle will damage your vehicle. The tires are particularly susceptible to damage.fDo not point the cleaning jet directly at any of the aforementioned components.
Decorative film
Risk of damage due to separation of the decorative film when using high-pressure cleaning equipment, steam cleaners or similar cleaning equipment.fDo not use high-pressure cleaning equipment, steam cleaners, etc. to clean decorative films.
Care of door lock
fTo prevent the door lock from freezing during the cold season, cover the lock barrel with suitable adhesive tape while washing the vehicle.
If the lock still freezes, use an ordinary de-icer. In many cases, a well warmed key can help.fNever use excessive force.
Car washing
The best protection for the vehicle from the damaging effects of the environment is frequent washing and preservation.
The longer road salt, road dust, industrial dust, insect remains, bird excrement, and tree exudations (e.g. resin, pollen), etc. are allowed to remain on the bodywork, the more harmful their effect.
Observe the following points in order to ensure that the vehicle is washed thoroughly without damaging the paintwork: fThe underside of the vehicle should also be thoroughly washed at the end of the gritting season at the latest.fWash your vehicle only at sites provided for this purpose to prevent soot, grease, oil and heavy metals from entering the environment.
fNew cars should be washed carefully with plenty of clear water to protect the new paint work. Dark paint finishes show up the smallest of surface damage (e.g., scratches) more readily than lighter colors. Dark colors are slightly more susceptible to scratching and require particularly careful paint care.Dark paints make even the smallest surface blemishes (scratches) more conspicuous than lighter colors.fDo not wash your Porsche in direct sunlight or when its body is hot.fWhen washing by hand, use a car shampoo, plenty of water, and a soft sponge or washing brush.We recommend Porsche car shampoo.fStart washing the vehicle by thoroughly wetting the paintwork and rinsing the heavy dirt off.fAfter washing the vehicle, rinse it thoroughly with water and rub it dry with chamois-leather.Do not use the same chamois for rubbing dry as you use for cleaning the windshield and windows.
Reduced or uneven braking action may be caused by wet brakes.fAfter washing the vehicle, test the brakes and steering and briefly brake the disks dry.When doing so, make sure that vehicles traveling behind you are not affected.
NOTICENOTICE
Wet BrakesWARNINGh
14_991_Turbo_21.book Seite 232 Mittwoch, 9. April 2014 2:19 14