Button PORSCHE 911 TURBO 2014 6.G Manual PDF

Parking 213
In front of the vehicle: 5. Hold the original remote control approx. 8 in. (20 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A on the overhead operating console starts flashing quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
6. The turn signal lights will flash once when the 5 minute teaching readiness period has elapsed.Repeat steps 3 to 5.7. Repeat steps 3 to 5 to assign further signals to the remaining buttons.
Assigning garage door opener signal to button with changeable code system
With some systems, a changeable code also needs to be programmed for the HomeLink® system. A second person makes programming easier.
Identifying the changeable code
fPress and hold the previously programmed HomeLink® button.
If the indicator light A on button II in the overhead operating console starts to flash quickly and lights up continuously after approx. 2 seconds, it means that the equipment has a changeable code system.fInformation on synchronization can also be found in the operating instructions for the system to be programmed.
Assigning garage door opener signal to key
fPark the vehicle within the range of the remote- controlled equipment.
On the overhead operating console: 1. Switch on ignition. 2. The standard factory-set codes must be deleted before programming for the first time.
For information on deleting the factory-set codes:fPlease see the chapter “PROGRAMMING GARAGE DOOR OPENER: DELETING AND STORING SIGNALS” on page 212.3. Press and hold the desired button on the overhead operating console keypad until the indicator light A on button II starts to flash slowly.You now have 5 minutes to teach the button.4. Stand in front of the vehicle with the original remote control of the system to be programmed.
In front of the vehicle: 5. Hold the original remote control approx. 12 in. (30 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A on the overhead operating console starts flashing quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
14_991_Turbo_21.book Seite 213 Mittwoch, 9. April 2014 2:19 14

214 Parking
6.The turn signal lights will flash once when the 5 minute teaching readiness period has elapsed.Repeat steps 3 to 5.7. Repeat steps 3 to 5 to assign further signals to the remaining buttons. 8. Locate the programming button on the receiver of the equipment to be programmed, e.g. on the motor unit of the garage door opener.
Synchronizing the system
9. Activating the motor unit: Press the programming button on the receiver of the garage door opener.You then usually have approx. 30 seconds to initiate step 10 (a setting indicator is usually activated on the motor unit).10. Programming on the overhead operating console:Press the button you selected in step 3 three times on the overhead operating console keypad (you must press the button on the keypad several times to complete the setting process for some devices).11. Repeat steps 3 to 10 to assign signals to the other buttons.12. After completing programming on the overhead operating console, the system should recognize the HomeLink® signal and launch as soon as the memory button is pressed when the ignition is switched on.
Reprogramming an individual button on the keypad
A HomeLink® button can be individually reprogrammed without deleting the rest of the button assignments.
On the overhead operating console: 1. Switch on ignition. 2. Press and hold the button to be programmed on the overhead operating console keypad (approx. 20 seconds), until indicator light A on button II flashes slowly. You now have 5 minutes to teach the button.3. Stand in front of the vehicle with the original remote control of the system to be programmed.
In front of the vehicle: 4. Hold the original remote control approx. 12 in. (30 cm) away from the marked position ( illustration) and press and hold the transmit button (for more than approx. 1 minute in some cases) until the vehicle’s turn signal lights flash on and off three times or the indicator light A in the overhead operating console starts to flash quickly.The turn signal lights flash three times and the indicator light A flashes quickly to confirm that the new signal has been programmed successfully.Several attempts with different distances between the vehicle and the original remote control may be necessary.With some systems, the transmit button on the original remote control may need to be pressed again when the indicator light on the original remote control goes out.
5. The turn signal lights will flash once when the 5-minute teaching readiness period has elapsed.Repeat steps 1 to 4.6. Repeat steps 1 to 4 to assign further signals to the other buttons.
Information
fPlease consult an authorized Porsche dealer if you have not been able to successfully assign signals to the buttons even though you have carefully followed the instructions in this section and the operating instructions for the original remote control. Your authorized Porsche dealer has a list of all garage door opener signals that can be adapted.fMake sure that the battery in the remote control for the garage door opener is new. If the battery voltage is inadequate, faults may occur in signal transmission. The system in the vehicle then learns the wrong code, which will not be recognized reliably by the garage door opening mechanism.
14_991_Turbo_21.book Seite 214 Mittwoch, 9. April 2014 2:19 14

216 Alarm System and Theft Protection
Alarm System and Passenger
Compartment Monitoring
FCC Numbers :
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation of this device is subject to the following two conditions:1. This device may not cause harmful interference, and 2. this device must accept any interference received including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modification could void the user's authority to operate the equipment.
The alarm system monitors the following alarm contacts:– Alarm contacts in doors, luggage compartment lid, engine compartment lid and headlights.– Interior surveillance: Movement in the interior when the vehicle is locked, e.g. attempted theft after breaking a window.– Inclination sensor country-specific equipment: inclination of the vehicle (e.g. when attempting to tow).
If one of these alarm contacts is interrupted, the alarm horn sounds for approx. 30 seconds and the emergency flasher flashes.After 5 seconds of interruption, the alarm is triggered again. This cycle is repeated up to ten times.
Switching on
fThe alarm system is activated when the vehicle is locked.
Switching off
fThe alarm system is deactivated when the vehicle is unlocked.
Information
fIf you unlock the vehicle with the emergency key in the door lock, you must switch the ignition on (ignition lock position 1) within 10 seconds of opening the door in order to prevent the alarm system from being triggered.
Information
If button on the car key is pressed and a door or the luggage compartment lid is not opened, the vehicle is locked again automatically after 30 seconds.
Switching off the alarm system if it is triggered
fUnlock vehicle or switch on ignition.
Switching off interior surveillance and inclination sensor
If people or animals are remaining in the locked vehicle or the vehicle is being transported on, e.g. a train or ship, the interior surveillance system and inclination sensor must be switched off temporarily.fInform any persons remaining in the vehicle that the alarm system will be triggered if the door is opened.
Using the car key
fQuickly press button on the car key twice within 2 seconds.The emergency flasher flashes slowly once.The doors are locked, but can be opened from inside.
USA: KR55WK50138
Canada: 7812D-5WK50138
14_991_Turbo_21.book Seite 216 Mittwoch, 9. April 2014 2:19 14

Alarm System and Theft Protection 217
On vehicles with Porsche Entry & Drive
fQuickly press button A in the door handle twice within 2 seconds. The emergency flasher flashes slowly once.The doors are locked, but can be opened from inside.
Information
The interior surveillance system and inclination sensor remain switched off if:– The interior surveillance system and inclination sensor were switched off when you last locked the vehicleandIf button A was pressed and a door or the luggage compartment lid was not opened.
Function indication
On vehicles without Porsche Entry & Drive, the locking condition of the vehicle is indicated by the indicator lights in the central locking button flashing at different frequencies.The indicator lights go out when the vehicle is unlocked.
On vehicles with Porsche Entry & Drive, the locking condition of the vehicle is indicated by the indicator lights in the doors flashing at different frequencies.
Alarm system is activated
– The indicator lights flash quickly twice when the vehicle is being locked, then flash normally.
Alarm system is activated, interior surveillance and inclination sensor are switched off
– The indicator lights flash quickly while you are locking the vehicle, go out for 10 seconds and then flash normally.
Faults in the central locking system and alarm system
The indicator lights come on for 10 seconds, flash at double speed for 20 seconds and then flash normally.
Avoiding false alarms
fIf people or animals are remaining in the locked vehicle or the vehicle is being transported on a train or ship, for example, the interior surveillance system and inclination sensor must be switched off temporarily.fAlways close the sunroof and all door windows.
Immobilizer
There is a transponder (an electronic component), containing a stored code, in each key. Before the ignition is switched on, the ignition lock checks the code.
The immobilizer can be deactivated and the engine started using an authorized ignition key only.
Theft Protection
When leaving the vehicle, always:fClose the windows.fClose the sunroof.fClose the Convertible top (Cabriolet).fActivate the electric parking brake.fRemove the ignition key (or switch ignition off on vehicles with Porsche Entry & Drive).fClose the glove box.fClose all storage compartments.fRemove valuables, vehicle registration documents, telephone and house keys from the vehicle.fClose the luggage compartment lid.fClose the engine compartment lid.fLock the doors.
14_991_Turbo_21.book Seite 217 Mittwoch, 9. April 2014 2:19 14

Maintenance and Car Care 229
5.Operate the pump nozzle and refuel the vehicle.Do not add further fuel once the correctly operated automatic pump nozzle has switched off. Fuel could spray back or could flow over when heated.6. Replace the tank cap immediately after refueling and close it until you hear and feel it locking.7. Close the filler flap and press on the rear of the filler flap until it engages securely.
Information
If you lose the tank filler cap, you must replace it only with an original part.
Risk of damage to decorative foils.
Decorative foils may fade if they come into contact with fuel.fWipe off any spilled fuel immediately.
Emergency unlocking of the filler flap
If the electrical release mechanism is faulty, the filler flap can be opened as follows:fOpen the passenger’s door.fPull the button in the right-hand door aperture ( arrow). The filler flap pops open.
Portable Fuel Container
If the portable fuel container is damaged in an accident and fuel escapes, it could ignite or explode.fDo not carry a portable fuel container on journeys.fObserve the relevant laws which prohibit fuel transport.
Vapors from the fuel are hazardous to health.fDo not carry a portable fuel container in the occupant compartment.NOTICE
Transporting Filled Fuel Containers
Portable Fuel Container Vapor Hazard
DANGERh
WARNINGh
14_991_Turbo_21.book Seite 229 Mittwoch, 9. April 2014 2:19 14

244 Minor Repairs
Information
If the warning light and warning message appear when driving: fStop immediately in a suitable place.fDo not continue driving.Please contact an authorized Porsche dealer.
For information on warning messages on the multi- function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Electromechanical Power Steering
When the engine is stopped (e.g. when on tow), no power steering assistance is available.Increased force is required for steering.fExercise extreme care when your vehicle is being towed.fHave the fault corrected. Please contact an authorized Porsche dealer.
Changing Air Cleaner
Regular replacement of the filter element is part of servicing.fIn dusty conditions, clean the filter element more frequently and replace it if necessary.fPlease see the chapter “MEASUREMENTS ON TEST STANDS” on page 241.
Changing Particle Filters
Regular replacement of the filters is part of servicing.
Dirty filters can be the cause of reduced air throughput, e.g. the windows can mist up.fHave the filters replaced.Please contact an authorized Porsche dealer.
Information
The particle filters ensure that the fresh air entering the passenger compartment is virtually free of dust and pollen.fIf the outside air is polluted by exhaust fumes, press the recirculated-air button.
Tires and Wheels
The original equipment tires and wheel rims on your Porsche comply with all applicable Federal Motor Vehicle Safety Standards.
Information
The summer tires of your Sports Car have been specially developed and adapted for high performance.The tire characteristics change at low outside temperatures (below 15 °C).This can result in noises when parking or maneuvering at low outside temperatures.
For your safety remember the following:
– Wheel rims and wheel bolts are matched to fit your Porsche.– If you intend to use other than original equipment wheels, be sure that they conform to Porsche specifications for your model. Only tires with the same make and with the same specification code (e.g. “N0”, “N1”...) can be mounted.– The use of wheel rims and wheel bolts that do not meet specifications of the original factory installed equipment will affect the safe operation of your vehicle and affect warranty coverage.– Before you plan on exchanging wheels, or snow tires already mounted on the wheel rims, consult your authorized Porsche dealer. Your dealer has the technical information necessary to advise you which wheel rims and wheel bolts are compatible with the original factory installations.
No Power Steering AssistWARNINGh
14_991_Turbo_21.book Seite 244 Mittwoch, 9. April 2014 2:19 14

268 Minor Repairs
Row B
Row C
No. Designation A
1 Front lid light Front lid actuator
High beam, FL
Low beam, FL
Side marker light, FR
Turn signal lights, RL, FL
40
2 Raised brake light, spoiler
Rear lid actuator
Rear fog light, right
Reversing light, left
Brake light, left
Tail light, left
Daytime driving light, FL
15
3 Alarm horn 15
4 Interior lighting
Hall sensors
Orientation light
License plate light
Rear wiper electronics activation
Heated rear window relay
Central locking LED
Door panels LED
Ambient light
Raised brake light
Rear fog light, left
Brake light, right
Reversing light, right
Daytime driving light, FR
Tail light, right
15
5 Fuel pump relay and control unit 20
6 Filler flap close/open
Washer pump, front/rear
10
7 Front spoiler control unit 30
8 Air conditioning control unit 7,5
9 Instrument cluster Steering columnstopwatch
10
10 PCM 25
No. Designation A
1 Center console button panel Gateway control unit
Diagnostic socket Ignition lock Passenger compartment monitoring sensorLight switch
Bluetooth phone charger
15
2 Start-relevant loads
Footwell lights
Electric ignition lock anti-removal lock
Turn signal light indicator, FL/FR
Emergency flasher button LED
Electric ignition lock light
Side turn signal lights, FR/FL
High beam, FR
Low beam, FR
Turn signal light indicator, RR
Side marker light, FL
40
3 Vehicle Tracking System control unit 5
4 Horn 15
No. Designation A
5 Cabriolet: Convertible-top lock closing mechanism open/closed
Filler flap
Cabriolet: Convertible top storage compartment catch open/close
Rear spoiler control extend/retract
30
6 Power window control unit, FL 25
7 Headlight cleaning system 30
8 PSM control unit 25
9 Alarm siren 5
10 Not used
No. Designation A
14_991_Turbo_21.book Seite 268 Mittwoch, 9. April 2014 2:19 14

Minor Repairs 269
Row D
Fuses in right footwell
Row A
Row B
Row C
No. Designation A
1 Rear wiper 15
2 HomeLink 5
3 Left headlight 5
4 PDC control unit AFS control unitFront spoiler control unitFront cameraGateway/diagnostic socketAir quality sensor
5
5 PSM control unit 5
6 Steering column switching module Electronic steering gear
Refrigerant pressure sensor
5
7 Selector lever control unit 5
8 Right headlight 5
9 Interior mirror 5
10 Seat ventilation, left 5No. Designation A
1 Lower left: DC/DC converter, infotainment 40
2 Upper left:
DC/DC converter roof console power supply
40
3 Lower right: Fresh-air blower motorBlower regulator
40
4 Upper right:
Right seat control unit Seat adjustment
25
No. Designation A
1 Rain sensor 5
2 Air conditioning control unit 25
3 Not used
4 PDCC control unit 10
5 TPMS control unit 5
6 TV tuner 5
7 High-end subwoofer amplifier Subwoofer amplifier 40
25
8 Not used
9 Allwheel control unit 10
10 Reversing camera control unit 5
No. Designation A
1 Not used
2 Electric parking brake button 5
3 Not used
4 Cabriolet: Rear power window control unit 20
5 Temperature sensor for DMTL tank leakage diagnosis 5
6 Front wiper motor 30
7 Power window control unit, FR 25
8 Steering column adjustment 25
9 Roof console 5
10 Sound system amplifier 40 25
14_991_Turbo_21.book Seite 269 Mittwoch, 9. April 2014 2:19 14

Minor Repairs 271
5.Use the black jump lead to connect the negative terminal of the donor battery to the door arrester D. 6. Press button on the remote control for approx. 2 seconds to unlock the luggage compartment lid. The alarm system is switched off.7. Disconnect the negative lead first, then the positive lead.8. Push positive terminal C into the fuse box and fit the plastic fuse box cover.
Battery (12 volt)
The battery is located under the cover in the luggage compartment.
For information on removing the cover:fPlease see the chapter “TIRE FILLING COMPRESSOR” on page 198.fHave the battery removed and installed only by your authorized Porsche dealer.
fObserve all warning notes on the battery.fDisconnect the negative terminal on the battery during all work on the electrical system.fDo not lay tools or other metal objects on the battery as they could cause a short circuit across the battery terminal.
fCharge battery in a well-ventilated area.fNever charge a frozen battery. It may explode because of gas trapped in the ice. Allow a frozen battery to thaw out first.fDo not expose the battery to an open flame, electrical spark or a lit cigarette, since they can ignite hydrogen gas from the battery.
fDo not wipe the battery with a dry cloth.fBefore touching the battery, discharge any static electricity by touching the vehicle.
fAfter handling battery, always protect your skin and remove surface chemicals by washing thoroughly with soap and water.
fWear eye protection.fDo not allow battery acid to come in contact with your skin or eyes.fIf you get electrolyte, which is an acid, in your eyes or on your skin, immediately rinse with cold water for several minutes and call a doctor.
Electric ShockDANGERh
Battery Explosion Hazard
Static Electricity
Chemical Exposure
Battery Acid and Electrolyte Exposure
DANGERh
DANGERh
WARNINGh
WARNINGh
14_991_Turbo_21.book Seite 271 Mittwoch, 9. April 2014 2:19 14

282 Minor Repairs
Tying down vehicle on flat bed
1.Carefully feed towing straps through the opening in the rear wheels. Make sure metal parts of straps do not damage rim.Make sure the strap is flat over the rim bead.Make sure brake backing plate is not damaged.2. Secure straps to rear of flat bed. 3. Reel in hoist cable only far enough to tension tie-down straps.
Transporting the vehicle on car trains, ferries and car transporters
fTie the vehicle down only at its wheels.fDeactivate interior surveillance and the inclination sensor.fPlease see the chapter “ALARM SYSTEM AND PASSENGER COMPARTMENT MONITORING” on page 216.
Fire extinguisher
In cars with a fire extinguisher, the extinguisher is located under the front passenger seat.fTo remove the fire extinguisher in case of an emergency, hold the extinguisher with one hand and press the button PRESS on the fire extinguisher holder with the other hand ( arrow).
Information
fCheck the final inspection date on the fire extinguisher. If the fire extinguisher is used after its inspection interval has elapsed, it may not work properly.fAlways read the operating instructions on the fire extinguisher.fObserve the fire extinguisher manufacturer’s safety instructions on the label at the fire extinguisher handle.fThe fire extinguisher should be checked to ensure correct operation by a specialist workshop every 1-2 years.fHave the fire extinguisher refilled after use.
14_991_Turbo_21.book Seite 282 Mittwoch, 9. April 2014 2:19 14