radio PORSCHE 911 TURBO 2014 6.G Owners Manual
[x] Cancel search | Manufacturer: PORSCHE, Model Year: 2014, Model line: 911 TURBO, Model: PORSCHE 911 TURBO 2014 6.GPages: 300, PDF Size: 10.61 MB
Page 5 of 300
3
The reduced tire tread depth means that there is an increased risk of aquaplaning on wet roads. fWhen driving on wet or mud-covered roads reduce speed significantly.
Sport tires have a smaller tread depth, and thus can reach their wear limit sooner.It is important to check tire wear frequently to avoid risk of serious personal injury or death from worn tires.fCheck tire wear frequently.
Driving on Race Circuit
(e.g. Sports Driving Schools, Club
Sport Events)
Brake fluid, brake pads and brake disks
Brake fluid absorbs moisture from the air over time. This accumulation of water lowers the boiling point and can impair braking action if the brakes are subjected to high temperatures, such as can occur on race circuits (sports driving school, Club Sport events).
The brake fluid should therefore not be more than 12 months old if the vehicle is driven on race circuits (sports driving school, Club Sport events).fFor more information, see the “ Maintenance” booklet.
Wear on the brake pads and brake disks depends to a great extent on the driving style and driving conditions. Wear on the brake components is increased as a result of high temperatures, such as can occur on race circuits (sports driving school, Club Sport events). fBefore and after driving on race circuits (e.g. sports driving school, Club Sport events), it is important therefore to carry out a professional inspection of the brake pads and brake disks for wear.
Racing tires
The fitting of racing tires (e.g. slicks) for sporting events is not approved by Porsche.Very high cornering speeds can be achieved with racing tires. The resulting transverse acceleration values would jeopardize the adequate supply of oil to the engine.Porsche therefore refuses to accept any guarantee or liability for damage occurring as a result of non-compliance with this provision.
Setting and operating vehicle
components when driving
Setting or operating the multi-function display, radio, navigation system, telephone or other equipment when driving could distract you from the traffic. You could lose control of the vehicle resulting in serious personal injury or death.fOperate the components while driving only if the traffic situation allows you to do so safely.fCarry out any complicated operating or setting procedures only with the vehicle stationary.
Loss of Road Surface Contact, Control over the Vehicle and Braking Ability
Worn Tires
DANGERh
DANGERh
Operating Components While Driving
WARNINGh
14_991_Turbo_21.book Seite 3 Mittwoch, 9. April 2014 2:19 14
Page 18 of 300
16 Opening and Locking
Never invite car theft!
An unlocked car with the key in the ignition lock invites car theft.
A gong alarm is standard equipment in your Porsche. The gong alarm will sound if you open the driver's door while the key is still in the ignition lock. It is your reminder to pull the key out of the ignition lock and to lock the doors.
Never leave your vehicle unattended with the key in the ignition lock, especially if children and/or pets are left unattended in the vehicle. They can operate power windows and other controls. If the engine is left running, they may accidentally engage the shift lever. Serious personal injury or death could result from loss of control of the vehicle.fAlways remove the ignition key.fAlways set the electric parking brake.fLock the doors with the key or with the remote control.
To protect your vehicle and your possessions from theft, you should always proceed as follows when leaving your vehicle:fClose windows.fClose sun roof.fActivate the electric parking brake.fRemove ignition key (switch ignition off in vehicles that have Porsche Entry & Drive).fRemove valuables (e.g. car documents, radio control module, cell phones, house keys) from the car.fLock doors.fLock the glove compartment.fClose storage trays.
Notes on the Key and Central
Locking System
Key
You are provided with two car keys with integrated emergency key. These keys operate all the locks on your vehicle.fBe careful with your car keys: do not part with them except under exceptional circumstances.fRemove and take the ignition key with you, even if leaving the vehicle only briefly.Do not leave the ignition key in the vehicle.fInform your insurance company of any loss or theft of car keys or if extra or replacement keys have been cut.fThird parties can still operate the mechanical locks with a lost key.
Information
Different vehicle settings are stored on the respective key when the vehicle is locked, provided the vehicle is fitted with the relevant equipment.
For information on storing vehicle settings on the key:fPlease see the chapter “COMFORT ENTRY FUNCTION” on page 34.
Unattended VehicleWARNINGh
14_991_Turbo_21.book Seite 16 Mittwoch, 9. April 2014 2:19 14
Page 20 of 300
18 Opening and Locking
Central Locking System
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation of this device is subject to the following two conditions:1. This device may not cause harmful interference, and 2. this device must accept any interference received including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modification could void the user's authority to operate the equipment.
Any changes or modifications not expressly approved by Porsche could void the user’s authority to operate this equipment.
Your vehicle is equipped with a central locking system. The following are unlocked or locked together:– Doors– Filler flap
The central locking system is always activated when the vehicle is unlocked and locked.
On the multi-purpose display of the instrument panel, you can set different variants for locking and unlocking. You can open all doors irrespective of the setting made.
The vehicle cannot be locked if the driver’s door is not completely closed.
If one of the following components is not completely closed when you try to lock the vehicle the door is not locked:– vehicle doors– luggage compartment lid
The indication by the emergency flasher and by the acoustic signal will be provided after all doors and the luggage compartment lid are closed.
Information
When locking the vehicle with only the driver's door closed, the vehicle will be pre-locked. Make sure that the key is not inside the vehicle when closing the open passenger's door/luggage compartment lid.
USA: KR55WK50138
Canada: 7812D-5WK50138
14_991_Turbo_21.book Seite 18 Mittwoch, 9. April 2014 2:19 14
Page 29 of 300
Opening and Locking 27
The vehicle cannot be unlocked
Remote control of the car key may – fail due to a fault,– due to a flat key battery,– not function correctly due to radio waves (also radio contact between remote control and vehicle in the case of Porsche Entry & Drive).
If the vehicle cannot be opened, then: 1. Place the car key at the outside edge of the windshield on the passenger’s side and, at the same time, press button ( illustration).
If the vehicle still cannot be opened, then: 2. Remove the emergency key from the car key. Please see the chapter “EMERGENCY KEY” on page 17.
3. Unlock and open the driver’s door with the emergency key.For this purpose, lift and hold the door handle.Insert the emergency key in the door lock, turn 90° anti-clockwise and remove the emergency key again.4. Release the door handle and open the door by pulling the door handle again.5. Switch on the ignition within 15 seconds to prevent the alarm system from triggering.Further procedure for vehicles with Porsche Entry & Drive:If the ignition cannot be switched on or if the engine will not start, the message “ Key not found or key fault Change key position ” will appear on the multi-function display.6. Turn control unit back to ignition lock position 0. 7. Try to start the engine again. If the engine will not start, the message ““ Key not found or key fault Change key position ” will appear again. The message “ Operating device: turn left, pull off, insert key ” appears after approx. 1 second.8. Turn control unit back to ignition lock position 0 and remove it from the ignition lock. Switch on the ignition using the ignition key (not the emergency key).
Switching off operational readiness (for vehicles with Porsche Entry & Drive)
Operational readiness of Porsche Entry & Drive is switched off after 96 hours for the driver’s door and after 36 hours for the passenger's door, if the vehicle is not unlocked within this time.1. Pull the door handle once to activate the system again.2. Pull the door handle again to open the door.
14_991_Turbo_21.book Seite 27 Mittwoch, 9. April 2014 2:19 14
Page 31 of 300
Opening and Locking 29
Door lock under door handle (driver‘s side)
The vehicle cannot be locked
This is recognizable by the fact that the emergency flasher does not flash and there is no locking noise.
The remote control of the key may – fail due to a fault,– due to a flat key battery,– not function correctly due to radio waves(e.g. mobile phone) in the vicinity of the vehicle (even radio contact between remote control and vehicle in the case of Porsche Entry & Drive).
Emergency locking if the central locking system has failed
If the vehicle cannot be locked, then: 1. Remove the emergency key from the car key. Please see the chapter “EMERGENCY KEY” on page 17.2. Open the driver’s door.
3. Lift the door handle on the driver’s door ( illustration). Insert the emergency key in the door lock, turn 90° clockwise and remove the emergency key again.Successful locking is indicated by the hazard warning lights flashing twice.4. Release the door handle and shut the door. The driver’s door is now locked.5. To use the emergency locking function on the passenger’s door , insert the emergency key into the door lock on the driver’s door again, turn 90° clockwise and remove the emergency key again.The passenger’s door is now locked.
Information
Emergency locking of the passenger’s door is not possible if the central locking system is defective.
Information
If the central locking system is defective, operating the lock cylinder in the driver’s door will lock all functioning locking elements of the central locking system.fHave faults in the central locking system repaired by an authorized Porsche dealer.
Emergency key
Removing emergency key
1. Push the release button to the side. 2. Pull out the key.
Insert emergency key
fPush in the key until the release button engages audibly.
Information
Different vehicle settings are stored on the respective key when the vehicle is locked, provided the vehicle is fitted with the relevant equipment.
14_991_Turbo_21.book Seite 29 Mittwoch, 9. April 2014 2:19 14
Page 54 of 300
52 Seats, Mirrors and Steering Wheel
Adjusting steering wheel
fMove the control switch under the steering column in the relevant direction until the desired setting is reached.
The steering wheel setting is stored in the vehicle settings.
For further information on storing and retrieving the steering wheel setting:fPLEASE SEE THE CHAPTER “COMFORT ENTRY FUNCTION” on page 34.
Multi-function Steering Wheel
You may be distracted from paying attention to the road if you set or operate the multi-function display, radio, navigation system, telephone or other equipment when driving. You may lose control of the vehicle.fOperate the equipment when driving only if the traffic situation allows you to do so safely.fCarry out any complicated operating or setting procedures only when the vehicle is stationary.
Depending on the equipment in your vehicle, you can use the function keys of the multi-function steering wheel to operate the following Porsche communication systems:– Telephone– PCM– CDR-31– Multi-function display in the instrument panel
Readiness of the multi-functional steering wheel for operation
– With ignition switched on.fPlease observe the operating instructions supplied for the Porsche communication systems before operating the function buttons.
Information
The Porsche communication systems cannot be switched on and off using the multi-function steering wheel.
Setting and operating when drivingWARNINGh
14_991_Turbo_21.book Seite 52 Mittwoch, 9. April 2014 2:19 14
Page 98 of 300
96 Instrument Panel and Multi-Function Display
Operating the Multi-Function
Display on the Instrument Panel
On the multi-function display, you can view information relating to the relevant vehicle equipment, operate the audio source (radio, CD, iPod, etc.), check the oil level, check the tire pressure, use the stopwatch or operate the navigation system.You can also modify different vehicle settings in the “ Vehicle” menu.
It is not possible to describe all details of the functions in this Owner’s Manual. The examples clearly demonstrate the functional principle and clarify the menu structure.
You may be distracted from paying attention to the road if you set or operate the multi-function display, radio, navigation system, telephone or other equipment when driving. You may lose control of the vehicle.fOperate the equipment while driving only if the traffic situation allows you to do so safely.fCarry out any complicated operating or setting procedures only when the vehicle is stationary.
Multi-function display
Information
The multi-function display is only active when the ignition is on.Certain menus are only available when the vehicle has stopped, e.g. the adjustment menu for tire pressure monitoring.
Operating principle on vehicles without multi-function steering wheel
The multi-function display is operated with the lower lever on the right of the steering column.
Selecting menu, function, setting option
fPush the lever downwards (position 3) or upwards (position 4).
Confirming selection (Enter)
fPush the lever forward (position 1).
Moving back one or several selection levels
fPull the lever towards the steering wheel (position 2) once or several times.
Operation of the multi- function display, radio, navigation system, telephone etc. during driving.
WARNINGh
14_991_Turbo_21.book Seite 96 Mittwoch, 9. April 2014 2:19 14
Page 99 of 300
Instrument Panel and Multi-Function Display 97
Operating principle on vehicles with multi-function steering wheel
The multi-function display is operated using the rotary knob A, the Back button B and the diamond ◊ button C, which can be assigned as required. fPlease see the chapter “FUNCTION BUTTONS ON THE MULTI-FUNCTION STEERING WHEEL” on page 53.
Selecting menu, function, setting option
fTurn rotary knob A upwards or downwards.
Confirming selection (Enter)
fPress rotary knob A.
Moving back one or several selection levels
fPress button B (Back button).
Individual assignment of the diamond button
Porsche Communication Management (PCM) functions, CDR functions or multi-function display functions can be assigned to the ◊ button in the multi-function display on the instrument panel. Audio source selection is preset by default.
For information on individual assignment of the ◊ button:fPlease see the chapter “CHANGING BUTTON ASSIGNMENT ON MULTI-FUNCTION STEERING WHEEL” on page 127.
For information on Porsche Communication Management (PCM) and CDR:fPlease refer to the separate operating instructions.
A - Upper status area B - Title area with menu indicator C - Information area D - Lower status area
Areas on the multi-function display
Upper status area/Lower status area
The upper A and lower status area D permanently display basic information, such as the radio station, compass, time and temperature or the remaining range.
14_991_Turbo_21.book Seite 97 Mittwoch, 9. April 2014 2:19 14
Page 104 of 300
102 Instrument Panel and Multi-Function Display
Measuring the oil level after topping up engine oil or opening the engine compartment lid
The oil level can be checked after waiting for approx. 1 minute with the vehicle parked on a level surface and the engine at operating temperature.
If the engine compartment lid is opened when the engine is cold (e.g. in order to top up engine oil), the oil level cannot be displayed for a certain time.The message “ No information about oil level available at present ” appears on the multi- function display.fEngine oil should therefore only be topped up with the engine at operating temperature. This ensures short waiting times for the soonest possible oil level display.
Failure
If the oil-level indicator fails, the message “ Oil level measurement fault Consult a workshop Driving permitted ” appears on the multi-function display.
Setting speed limits
If a speed limit is preset and activated on the multi-function display, a warning message appears if the speed limit is exceeded.A speed limit can be used to remind the driver to keep to the maximum speed permitted for the tire type fitted to the vehicle, for example.
Setting a speed limit
You can either adopt the current speed of the vehicle or specify your own speed limit.
Activating and deactivating speed limits
Adjusting vehicle settings
Various vehicle settings can be modified in the “ Settings” submenu.
For information on modifying vehicle settings:fPlease see the chapter “VEHICLE SETTINGS ON THE MULTI-FUNCTION DISPLAY” on page 117.
Audio Menu
In the “ Audio” main menu, you can select a radio station either from the station list or the list of stored stations, depending on the settings, or a track from the active audio source, e.g. disk.
For information on adjusting audio menu settings:fPlease see the chapter “ADAPTING DISPLAY CONTENTS OF AUDIO MAIN MENU” on page 118.
1. Main menu “Vehicle” > “ Limits” and confirm.
1. Main menu “Vehicle” > “ Limits”
2.Select “Limit 1: ---” or “ Limit 2: ---“ and confirm.
3. Select “Current speed” or „ ---“ and confirm.
1. Main menu “Vehicle” > “ Limits”
2.Select “Limit 1: ---” or “ Limit 2: ---“ and confirm.
3. Select “Active”
4.Confirm your selection.
Limit is active.
Limit is not active.
1. Select “Audio” in the main menu and confirm.
2. Select the desired radio station or track and confirm.
14_991_Turbo_21.book Seite 102 Mittwoch, 9. April 2014 2:19 14
Page 115 of 300
Instrument Panel and Multi-Function Display 113
Warning light
The warning light in the instrument panel lights up: – When a loss in pressure has been detected (warning light: lights up continuously).– In the event of a defect in TPMS or a temporary fault (warning light: flashes for 60 seconds, then lights up continuously).– When learning new fitted wheels/wheel transmitters, as long as the vehicle’s own wheels have not yet been recognized (warning light: flashes for 60 seconds, then lights up continuously).
A warning message also appears on the multi- function display in the instrument panel.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
The tire pressure warning light on the instrument panel goes out only when the cause of the fault has been rectified.
Changing a wheel and replacing tires
fNew wheels must be fitted with radio transmitters for Tire Pressure Monitoring System. Before tires are changed, the battery charge condition of the wheel transmitters should be checked.fPlease contact an authorized Porsche dealer.fSwitch off the ignition when changing a wheel.
The tire settings on the multi-function display must be updated after changing a wheel.If the tire settings are not updated, the message “Tire change? Update settings” is displayed on the multi-function display.fUpdate the multi-function display settings the next time the vehicle is stationary.
Pressure increase as the result of temperature increase
In accordance with physical principles, the tire pressure changes as the temperature changes.For every 18 °F (10 °C) change in temperature, the tire pressure increases or decreases by around 1.5 psi/0.1 bar/10 kPa.
Partial monitoring
Monitoring of the other wheels is continued if there is a fault in one or two wheel transmitters.– The tire pressure warning light lights up.– The message “Restricted monitoring” appears on the multi-function display.– No tire pressures are displayed on the multi-function display for wheels with faulty wheel transmitters.
No monitoring
In the event of faults, Tire Pressure Monitoring System cannot monitor the tire pressure. The warning light on the instrument panel lights up and a corresponding message appears on the multi-function display.
Monitoring is not active: – In the event of a defect in TPMS or if more than 2 wheel transmitters are defective.– If wheel transmitters for Tire Pressure Monitoring System are missing.– During the learning phase after the tire settings have been updated.– After a wheel change without updating the tire settings.– If more than four wheel transmitters are recognized.– If there is external interference by other radio sources, e.g. wireless headphones.– If tire temperatures are too high.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
14_991_Turbo_21.book Seite 113 Mittwoch, 9. April 2014 2:19 14