ECU Ram 2500 2019 Workshop Manual

STARTING AND OPERATING 345
5. Pull the wire to the anchor point. Pull out enough wirerope to reach your anchor point. To prevent losing the
end, hold the hook strap while you work.
Pulling Synthetic Rope 6. Secure to the anchor point. Once you have established
your anchor point, secure the tree-trunk protector or
choker-chain around the object.
Tree Trunk Protector
CAUTION!
Always be certain the anchor you select will withstand
the load.
5

346 STARTING AND OPERATING
NOTE:
How to choose an anchor point: A secure anchor is critical to
winching operations. An anchor must be strong enough to
hold while winching. Natural anchors include trees, stumps
and rocks. Hook the cable as low as possible. If no natural
anchors are available when recovering another vehicle, your
vehicle becomes the anchor point. In this case, be sure to put
the transmission in NEUTRAL, apply the hand brake and
block its wheels to prevent your vehicle from moving.
Ideally, you'll want an anchor point that will enable you to
pull straight in the direction the vehicle will move. This
allows the synthetic rope to wind tightly and evenly onto the
spooling drum. An anchor point as far away as possible will
provide the winch with its greatest pulling power.
7. Attach the Clevis/D-shackle and Tree Trunk Protector. Attach the shackle to the two ends of the strap or chain
and through the hook, being careful not to over tighten
(tighten and back-off 1/2 turn). Clevis/D-Shackles
8. Lock the clutch. Lock the winch drum by rotating the clutch lever on the winch to engage.
NOTE:
Always ensure the clutch is fully engaged or disengaged.

STARTING AND OPERATING 347
9. Connect the remote control to the winch control box,located on the front bumper. Be careful not to let the
remote control cord dangle in front of the winch. If you
choose to control the winch from inside your vehicle,
always pass the remote through a window to avoid
pinching the cord in the door. Always disconnect the
remote control when not in use.
Winch Box Remote Control Connector 10. Put synthetic rope under tension. Using the remote
control switch, slowly wind the rope until no slack
remains. Once the rope is under tension, stand well clear
of it and never step over it.
Pulling Synthetic Rope Under Tension
11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the
winching procedure.
5

350 STARTING AND OPERATING
NOTE:•Avoid overheating the winch motor. For extendedwinching, stop at reasonable intervals to allow the
winch motor to cool down.
•What to look for under load: The synthetic rope must always spool onto the drum as indicated by the drum
rotation decal on the winch. As you power-in, make
sure the synthetic rope winds evenly and tightly on the
drum. This prevents the outer rope wraps from
drawing into the inner wraps, binding and damaging
the synthetic rope. Avoid shock loads by using the
control switch intermittently to take up rope slack.
Shock loads can momentarily far exceed the winch and
synthetic rope ratings. During side pulls the synthetic
rope tends to stack up at one end of the drum. This
stack can become large enough to cause serious
damage to the winch. So, line up pulls as straight ahead
as possible and stop winching if the synthetic rope
comes close to the tie rods or mounting plate. To fix an
uneven stack, spool out that section of the rope and
reposition it to the opposite end of the drum, which will
free up space for continued winching. 15. Secure vehicle. Once recovery of the vehicle is complete,
be sure to secure the vehicle's brakes and shift the trans -
mission to PARK. Release tension in the synthetic rope.
16. Disconnect the synthetic rope, and disconnect from the anchor.
17. Rewind the synthetic rope. The person handling the synthetic rope should walk the rope in and not let it slide
through the hand, control the winch at all times.
Rewinding The Synthetic Rope

352 STARTING AND OPERATING
Rigging Techniques
Various winching situations will require application of other
winching techniques. These could range from too little
distance to achieve maximum pull using straight line
rigging, simply increasing pulling power, or maintaining a
straight-line pulling situation. You will have to assess what
technique is correct for your situation. Think "safety" at all
times.How To Change The Pulling Direction
Change Pulling Directions
All winching operations should have a straight line from the
winch to the object being pulled. This minimizes the
synthetic rope collecting on one side of the drum affecting
pulling efficiency and damaging synthetic rope. A snatch
block, secured to a point directly in front of the vehicle will
enable you to change your pulling direction while still
allowing the synthetic rope to be at 90° to wind properly onto
the spooling drum.

STARTING AND OPERATING 353
Increasing Pulling Power
In some cases, you may find yourself needing more pulling
power. The use of snatch blocks increases mechanical advan-
tage and that increases your pulling power.
Double Line
Wire Rope Routing Because pulling power decreases with the number of layers
of synthetic rope on the winch drum, you can use a snatch
block to double line out more rope. This decreases the
number of layers of synthetic rope on the drum, and
increases pulling power. Start by feeding out enough
synthetic rope to free the winch hook. Attach the hook to
your vehicle's frame/tow hook and run the rope through a
snatch block. Disengage the clutch and, using the snatch
block, pull out enough synthetic rope to reach your anchor
point. Do not attach the hook to the mounting kit. Secure to
the anchor point with a tree trunk protector or choker chain.
Attach the clevis/shackle. Attach the shackle to the two ends
of the strap/chain, being careful not to over tighten (tighten
and back-off 1/2 turn).
5

STARTING AND OPERATING 409
NOTE:
• When the fuel nozzle “clicks” or shuts off, the fuel tank isfull.
• Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The
MIL in the instrument cluster may turn on if the gas cap is
not secured properly. Make sure that the gas cap is tight -
ened each time the vehicle is refueled.WARNING!
• Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is
being filled.
• Never add fuel to the vehicle when the engine is running.
• A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be
burned. Always place gas containers on the ground
while filling.
CAUTION!
• Damage to the fuel system or emissions control system could result from using an improper fuel tank filler
tube cap.
• A poorly fitting fuel filler cap could let impurities into the fuel system.
• A poorly fitting fuel filler cap may cause the “Malfunc -
tion Indicator Light (MIL)” to turn on.
• To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. When the fuel nozzle “clicks”
or shuts off, the fuel tank is full.
WARNING!
• Always place container on the ground before filling.
• Keep the pump nozzle in contact with the container when you are filling it.
• Use only approved containers for flammable liquid.
• Do not leave container unattended while filling.
• A static electric charge could cause a spark and fire hazard.
5

STARTING AND OPERATING 411
Curb Weight
The curb weight of a vehicle is defined as the total weight of
the vehicle with all fluids, including vehicle fuel, at full
capacity conditions, and with no occupants or cargo loaded
into the vehicle. The front and rear curb weight values are
determined by weighing your vehicle on a commercial scale
before any occupants or cargo are added.
Loading
The actual total weight and the weight of the front and rear
of your vehicle at the ground can best be determined by
weighing it when it is loaded and ready for operation.
The entire vehicle should first be weighed on a commercial
scale to insure that the GVWR has not been exceeded. The
weight on the front and rear of the vehicle should then be
determined separately to be sure that the load is properly
distributed over the front and rear axle. Weighing the vehicle
may show that the GAWR of either the front or rear axles has
been exceeded but the total load is within the specified
GVWR. If so, weight must be shifted from front to rear or
rear to front as appropriate until the specified weight limita-
tions are met. Store the heavier items down low and be sure
that the weight is distributed equally. Stow all loose items
securely before driving. Improper weight distributions can have an adverse effect on
the way your vehicle steers and handles and the way the
brakes operate.
TRAILER TOWING
In this section you will find safety tips and information on
limits to the type of towing you can reasonably do with your
vehicle. Before towing a trailer, carefully review this infor
-
mation to tow your load as efficiently and safely as possible.
To maintain the New Vehicle Limited Warranty coverage,
follow the requirements and recommendations in this
manual concerning vehicles used for trailer towing. CAUTION!
Do not load your vehicle any heavier than the GVWR or
the maximum front and rear GAWR. If you do, parts on
your vehicle can break, or it can change the way your
vehicle handles. This could cause you to lose control.
Also overloading can shorten the life of your vehicle.
5

STARTING AND OPERATING 419
(Continued)
Perform the maintenance listed in the “Scheduled
Servicing”. Refer to “Scheduled Servicing” in “Servicing
And Maintenance” for the proper maintenance intervals.
When towing a trailer, never exceed the GAWR or GCWR
ratings.• Then, during the first 500 miles (805 km) that a trailer is
towed, do not drive over 50 mph (80 km/h) and do not
make starts at full throttle. This helps the engine and
other parts of the vehicle wear in at the heavier loads.
WARNING!
• Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that
is not fully secured, dynamic load shifts can occur that
may be difficult for the driver to control. You could lose
control of your vehicle and have a collision.
• When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of
control, poor performance or damage to brakes, axle,
engine, transmission, steering, suspension, chassis
structure or tires. CAUTION!
(Continued)
• Safety chains must always be used between your
vehicle and trailer. Always connect the chains to the
hook retainers of the vehicle hitch. Cross the chains
under the trailer tongue and allow enough slack for
turning corners.
• Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow
vehicle. Put the tow vehicle transmission in PARK. For
four-wheel drive vehicles, make sure the transfer case
is not in NEUTRAL. Always, block or "chock" the
trailer wheels.
• GCWR must not be exceeded.
• Total weight must be distributed between the tow vehicle and the trailer such that the following four
ratings are not exceeded:
1. GVWR
2. GTW
3. GAWR
4. Tongue weight rating for the trailer hitch utilized.
WARNING! (Continued)
5

STARTING AND OPERATING 431
Recreational Towing — Two-Wheel Drive Models
DO NOT flat tow this vehicle. Damage to the drivetrain
will result.
Recreational towing (for two-wheel drive models) is allowed
ONLY if the rear wheels are OFF the ground. This may be
accomplished using a tow dolly or vehicle trailer. If using a
tow dolly, follow this procedure:
NOTE:
If vehicle is equipped with air suspension, ensure the vehicle
is set to Normal Ride Height.
1. Properly secure the dolly to the tow vehicle, following the dolly manufacturer's instructions.
2. Drive the rear wheels onto the tow dolly.
3. Firmly apply the parking brake. Place automatic trans -
mission in PARK. 4. Properly secure the rear wheels to the dolly, following the
dolly manufacturer's instructions.
5. Turn the ignition OFF and remove the key fob.
6. Install a suitable clamping device, designed for towing, to secure the front wheels in the straight position.
CAUTION!
• Towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper
towing is not covered under the New Vehicle Limited
Warranty.
• Do not disconnect the driveshaft because fluid may leak from the transmission, causing damage to internal
parts.
5