check engine RENAULT CLIO 1997 X57 / 1.G Petrol Engines User Guide

ENGINE AND PERIPHERALS
En
gine repair10
92317S
91803G1 FITTING THE PISTON RINGS
Mount on the piston:
- the scraper ring (3),
- the taper compression piston ring (2), with the
"To
p" mark facing upwards,
- the upper piston ring (1), with the
"To
p" mark
facing upwards.
Once the seating of all the piston rings has been
adjusted, never alter this seating.
Oil and bed in the piston rings, seating the scrape
r
ring onto a solid part of the groove.Fit the "connecting rods - pistons - piston rings"
assemblies into the liners using the piston ring
compressor.
Before fitting the "liners - pistons - connecting
rods" assemblies into the cylinder block, do no
t
forget to fit the O-ring on each liner, ensuring
that it is not twisted.
Fit the assembly into the cylinder block in the pre-
established order, checking that a
0.1 mm shim
will pass freely between the liners.
92316S 918038630786314
10-41
Page 1 of 1 E_Series_43
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_43.htm

ENGINE AND PERIPHERALS
En
gine repair10
Immobilise the liners using tool
Mot. 588.
92062R
Shims of the following thicknesses (mm) are avai-
lable from the Parts Department:
2.80; 2.85; 2.90;
2.95.
Refit the connecting rod shells and tighten the
nuts to a torque value of
4.2 daN.m.
Check:
- the end float of the connecting rods,
- that the assembly is able to rotate properly. Fit the crankshaft and the end float shims.
Lubricate the crankpins and the main bearing
journals with engine oil.
Refit the crankshaft bearing shells.
Apply a thin layer of
RHODORSEAL 5661 on bea-
ring
N°
1 zone (K) and tighten the bolts to
2.5 daN.m , then angle tighten to
43°

± 6°.
Check the end floatof the crankshaft, which
should be between:
-
0.045 and 0.852 mmwith wear,
-
0.045 and 0.252 mmwithout wear.
92314S MOUNTING THE BEARING SHELLS
The connecting rod bearing shells are identical.
The crankshaft bearing shells are grooved on the
cylinder block side.
92315R
The upper shell of bearing
No. 5 is a special one
and is also grooved.
10-42
Page 1 of 1 E_Series_44
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_44.htm

ENGINE AND PERIPHERALS
En
gine repair10
Fit:
- the oil pump, checking that the centring dowls
are present, and tighten to a torque value of
2.5 daN.m,
- the two sprockets and chain of the oil pump,
and tighten the three bolts mounting the
sprocket to the hub to
1 daN.m,
- the crankshaft end cover, sealing it with
Loctite
518.
The bead (H) should be
0.6 to 1 mm wide and
should be applied as shown in the diagram be-
low. - the crankshaft seal (bearing No.1), using tool
Mot. 1129-01; this tool is designed to ensure an
offset seal bearing surface. Lubricate the lip
and the outside of the seal.
92319R
92067R
-the crankshaft end seal, using tool
Mot. 1128-
01; lubricate the lip and the outside diamete
r
of the seal.
Turn over the s
pacer if the old seal has marked
the bearin
g surface.
92318R
10-43
Page 1 of 1 E_Series_45
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_45.htm

ENGINE AND PERIPHERALS
En
gine repair10
There is an arrow painted on the back of the belt
showing the direction of rotation and two marks
for the setting.
Line up the marks (N) on the belt with those on
the sprockets (L) and the housings (M).
Respect the direction of mounting of the belt and
begin to position it on the crankshaft sprocket.
Fit the sensor of
Mot. 1273.
98708R
Turn the knurled wheel of the sensor until it re-
leases (three "clicks").
Tension the belt using tool
Mot. 1135-01 until
the display of the
Mot. 1273 shows the re-
commended fitting value
.
Belt tension (in SEEM units)
Fitting value: 30 U.S.
Lock the tension wheel, carry out a check and ad-
just the value.
Rotate the crankshaft at least
three turns.
Check that the tension value is within the fitting
tension tolerance (
±10 %), and if not readjust it.
NOTE : Never refit a belt which has been remo-
ved.
Tighten nut (O) of the tension wheel to 5 daN.m.
It is essential to tighten the tension wheel nut to
a tor
que value of 5 daN.m to prevent any risk of
working loose which might damage the engine.
WARNING: Certain camshaft s
prockets have five
marks, but onl
y the rectangular mark on the face
of a tooth shows the TDC. The other marks are
used for ad
justing the valve rockers.
10072S
Only the camshaft sprockets with marks will be
available in future from the Parts De
partment.
10-47
Page 1 of 1 E_Series_49
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_49.htm

ENGINE AND PERIPHERALS
En
gine repair10
Refit:
- the cylinder head cover fitted with a new gas-
ket,
- the coolant pipe and the dipstick guide tube
with new seals,
- the timing cover,
- the crankshaft pulley tightening the bolt to
2 daN.m, then angle tighten to
68°
±6°,
- the inlet and exhaust manifolds, tightening the
nuts to
2.5 daN.m,
- the accessories belt or belts.
Tensionin
g process
Engine cold (ambient temperature).
Fit the new belt.
Position the sensor of the
Mot. 1273.
Turn the knurled wheel of the sensor until it re-
leases (three "clicks").
Tension the belt until the fitting value recommen-
ded on the next page is shown on the display of
the
Mot. 1273.
Lock the tension wheel, carry out a check and ad-
just the value.
Rotate the crankshaft
three turns.
Check that the tension value is within the fitting
tension tolerance, and if not readjust it.
NOTE : Never refit a belt which has been remo-
ved.
10-50
Page 1 of 1 E_Series_52
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_52.htm

ENGINE AND PERIPHERALS
En
gine repair10
12310R
Tension(US = SEEM
Units)
Alternator
belt
Vee
F1
Grooved
3 teeth
F2Power assisted
steerin
g
belt
Grooved 3 teeth
F3
(E7J 764)F3 F4Air
conditionin
g
belt
Vee
F5Grooved 4 teeth
F6 F7Air conditionin
g and
power assisted
steerin
g
belt
Grooved 4
teeth
F8 F9Grooved 5
teeth
F8
Fitting
83 ± 7 84 ± 684 ± 684 ±5 84 ±490
102 ±6 103 ±4 106 110 ± 7110
Minimum
operating70 52 52 46 47 72 55 77 59 75 59
A Crankshaf
t
B Alternator
C Air conditioning compressor
D Power assisted steering pump
E Pulley
T Tension wheel
→ Tension checking poin
t
Alternator Power assisted steering
12311R
10-51
Page 1 of 1 E_Series_53
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_53.htm