ignition RENAULT KANGOO 2013 X61 / 2.G Access Security User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: KANGOO, Model: RENAULT KANGOO 2013 X61 / 2.GPages: 48, PDF Size: 0.31 MB
Page 38 of 48
82D-38
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
82D
UCH
Vdiag No.: 0F
ALP 7 The vehicle will not start
NOTESOnly refer to the customer complaints after performing a complete check using
the diagnostic tool.
Does the central locking operate?See 87B, Passenger compartment
connection unit.
Switch on the ignition. Has the immobiliser
warning light gone out?
Turn the starter.
Nothing happens.The starter clicks
but the engine
does not turn over.The starter motor
turns but there is
no engagement.The engine turns
but does not start.The engine turns
over progressively
more slowly and
does not start.
Perform an
injection domain
test using the
diagnostic tool.
See 13B, Diesel
Injection or 17B,
Petrol Injection.Check the battery
voltage. Check the
condition of the
starter.
NO
YES
NOA
YES
BCD
UCH_V0F_ALP07
ACCESS - SECURITY
Fault finding – Fault finding chart
Page 39 of 48
82D-39
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
ACCESS - SECURITY
Fault finding – Fault finding chart82D
UCH
Vdiag No.: 0F
ALP 7
CONTINUED 1
Is the immobiliser warning light illuminated
CONTINUOUSLY?Does the warning light flash?
Normally Rapidly
The UCH has not
detected the after
ignition feed.Carry out a test
using the
diagnostic tool and
deal with status
ET185 Key code
received.
See 87B, Passenger compartment
connection unit.Carry out a test using
the diagnostic tool
and deal with status
ET004 + 12 V after
ignition.
A
NO
YES
Page 40 of 48
82D-40
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
ACCESS - SECURITY
Fault finding – Fault finding chart82D
UCH
Vdiag No.: 0F
ALP 7
CONTINUED 2
Check the battery voltage with the starter motor activated and the + starter supply.
Check the condition of the starter exciter terminal. Repair if necessary.
Check for +12V at the starter excitation terminal, when the starter is activated.
Repair if necessary (ignition switch supply, correct operation of the ignition switch and ignition switch/starter
connection).
If the fault is still not resolved, check that the starter motor is operating correctly. Replace the starter motor if
necessary (see MR 374, Mechanical, 16A, Starting - Charging, Starter: Removal - Refitting).
B
Page 43 of 48
82D-43
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
ACCESS - SECURITY
Fault finding – Fault finding chart82D
UCH
Vdiag No.: 0F
ALP 8 No electric window operation
Switch on the + after ignition
Check the presence and condition of the fuses F19 (25 A) for the driver's electric window control, component code
132 and F20 (25 A) for the driver's electric window control for the front passenger window, component code 133
and F32 (25 A) for the passenger electric window control, component code 532 on the passenger compartment
fuse and relay box, component code 260.
Are they in good condition?
Replace the fuse(s) if the checks are not correct
(see MR 374, Mechanical, 81C, Fuses, Fuses:
List and location of components).
A
YESNO
UCH_V0F_ALP08