child lock RENAULT KANGOO 2013 X61 / 2.G Air Bags AC4 And Pretensioners Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: KANGOO, Model: RENAULT KANGOO 2013 X61 / 2.GPages: 40, PDF Size: 0.55 MB
Page 13 of 40
88C-13V1 MR-376-X76-88C000$040.mif
88C
2nd generation
(AC4 phase II)
REPLACING THE AIRBAG COMPUTER
The airbag computers are sold in locked mode to avoid all risk of accidental triggering (all ignition lines are inhibited).
The "locked" mode is indicated when the airbag fault warning indicator light on the instrument panel illuminates.
Follow this procedure when replacing an air bag computer:
– Make sure the ignition is switched off.
– Replace the computer (see MR Mechanical: MR-AIRBAGS-SRP, 88, Airbags and seat belt pretensioners,
Computer: Removal-refitting).
– Carry out a check using the diagnostic tool.
– If necessary, modify the computer configuration using the "Configuration" command.
– Switch off the ignition.
– Unlock the computer only if no faults are indicated by the diagnostic tool.
WARNING:
The owner of the vehicle may have locked the passenger front airbag to allow a child seat to be fitted to
the front passenger seat. In this case, the procedure for locking the passenger front airbag defined in the
Technical Note published for this subject has been applied, i.e.:
– Signing of a discharge by the customer (example in the Technical Note).
– Replacement of the passenger front seat belt.
– Disconnection of the passenger front airbag module.
– Locking of the trigger line of the passenger front airbag and modification of the computer configuration.
– Replacement of the "airbag" labels on the passenger side.
If this procedure has been applied, it is imperative to relock the passenger front airbag using the "Lock
passenger front airbag" command ("Configuration and programming" section).
It is vital that you never use this passenger airbag locking command before a Technical Note dealing with
the subject has been distributed.
AIRBAGS AND PRETENSIONERS
Fault finding – Replacement of components
Page 25 of 40
88C-25
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF016
PRESENTCOMPUTER CONFIGURATION
NOTESThis fault may appear after using the passenger airbag locking command, by not
observing the procedure described in the Technical Note (this command allows a child
seat to be fitted on the passenger seat).
It is vital that you never use this passenger airbag locking command before a
Technical Note dealing with the subject has been distributed.
This fault corresponds to an inconsistency between the computer configuration and the vehicle equipment
detected by the computer. The computer has detected the presence of a component additional to its configuration.
Modify the computer configuration using the Configuration command on the diagnostic tools.
Page 34 of 40
88C-34V1 MR-376-X76-88C000$070.mif
88C
2nd generation
(AC4 phase II)
Note: At the request of the customer, the passenger front airbag may have been locked to allow a child seat to be
fitted on the front passenger seat. In this case, the computer configuration is "Without" passenger front airbag and
the warning light flashes 12 seconds after being illuminated constantly for three seconds when the ignition is
switched on.
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
Order FunctionParameter or status
checked or actionDisplay/notesFault
finding
1Diagnostic tool
dialogue-ALP 1
2Computer
conformityVehicle type parameter
Kangoo VLL None
3Computer
configurationUsing the Reading
configuration commandCheck that the computer
configuration defined in the
"Current" column corresponds to
the vehicle equipment
If the Passenger front airbag line
is configured "Without", refer to
the NoteNone
4Warning light
operation
Computer
initialisation
check.Ignition onThe warning light illuminates for
3 seconds when the ignition is
switched on
If after being on for 3 seconds, the
warning light flashes for
12?seconds, consult the Note.None
It is vital that you never use this passenger airbag locking command before a Technical Note dealing with
the subject has been distributed.
AC4 ph2 airbag:
22
AIRBAGS AND PRETENSIONERS
Fault finding – Conformity check