DF056 RENAULT KANGOO 2013 X61 / 2.G Diesel DCM 1.2 Injection Workshop Manual

13B-23V1 MR-376-X76-13B000$060.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
Tool fault Associated DTC Diagnostic tool name
DF052 0200Injector control circuit
DF053 0089Rail pressure regulation function
DF056 0100Air flow sensor circuit
DF057 2264Water in diesel fuel detector circuit
DF059 0263Misfiring on cylinder 1
DF060 0266Misfiring on cylinder 2
DF061 0269Misfiring on cylinder 3
DF062 0272Misfiring on cylinder 4
DF089 0235Inlet manifold pressure sensor circuit
DF098 0180Fuel temperature sensor circuit
DF107 062FComputer memory
DF112 0340Cylinder reference sensor circuit
DF113 0641Sensor supply voltage
DF114 0400EGR solenoid valve circuit
DF121 0325Accelerometer circuit
DF122 0651Supply voltage pedal potentiometer gang 2
DF130 0087Flow capacity function
DF159 0635Power steering relay control circuit
DF162 0655Overheating indicator light
DF195 0016Camshaft/engine speed sensor consistency
DF209 0487EGR valve position sensor circuit
DF218 0604Microcontroller
DF221 0830Clutch contact signal
DF236 106FSerious injection fault warning light circuit

13B-79
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF056
PRESENT
OR
STOREDAIR FLOW SENSOR CIRCUIT1.DEF: Permanent low level
2.DEF: Permanent high level
3.DEF: At maximum limit
4.DEF: At minimum limit
NOTESPriorities when dealing with a number of faults:
– DF089 Inlet manifold pressure sensor circuit.
Special notes:
If fault DF056 is present: air flow regulation stops and the EGR valve is closed.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the condition of the air filter, replace the air filter if necessary (see MR388 (Logan/Sandero), MR423 (Thalia
2 / Symbol 2) or MR451 (Duster), Mechanical, 12A Fuel mixture, Air filter: Removal – Refitting).
Check that the inlet manifold is not obstructed (clogged).
Run TEST 5 Inlet circuit check.
Run TEST 11 Air line at the turbocharger
Check the connection and condition of the air flowmeter connector, component code 799.
Check the condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 12 V after ignition feed on connection 3FB (or 3FBA) of the connector of the air flowmeter,
component code 799.
Check for + 5 V on connection 3KJ of the connector of the air flowmeter, component code 799.
Check the earth on connection NH on the connector of the air flowmeter, component code 799.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
DCM1.2_V08_DF056

13B-80
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF056
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3KJ between components 120 and 799,
●3DV between components 120 and 799,
●3DW between components 120 and 799,
●3FB between components 799 and 1047 (only for the K9K 718 engine),
●3FBA between components 799 and 597 (only for the K9K 792, 796 engines),
●NH between component 799 and the earth (except Duster),
●3B between component 799 and 120 (for Duster).
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Also check the insulation between these connections.
If the fault is still present, replace the air flowmeter (see MR388 (Logan/Sandero) or MR451 (Duster),
Mechanical, 12A Fuel mixture, Air flowmeter: Removal – Refitting).
If the fault is still present, contact the Techline.

13B-123V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK (CONTINUED 1)
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Air
temperaturePR058:Air
temperatureGives the inlet air temperature
in °C. This information is
supplied by the air
temperature sensor
incorporated in the air
flowmeter.
Default value: 20°C.In the event of a fault, consult the
interpretation of parameter
PR058 then consult the
interpretation of fault DF056 Air
flow sensor circuit.
Fuel
temperaturePR063:Fuel
temperatureCold = PR064
Warm: 50°C
Gives the fuel temperature in
°C. This value is measured by
the fuel temperature sensor.
Default value: 30°C.If there is a fault, use the
interpretation of fault DF098 Fuel
temperature sensor circuit.
Manifold air
temperaturePR311:Manifold air
temperatureIf the value supplied by this
parameter is equal to 50°C,
this does not correspond to a
fault and no interpretation
should be made for this
engine.
Atmospheric
pressurePR035:Atmospheric
pressureIndicates the atmospheric
pressure in mbar. The sensor
is built into the computer. In the event of inconsistency,
with the engine stopped and
ignition on, check that parameter
PR035PR312local
atmospheric pressure. Inlet manifold
vacuumPR312:Inlet manifold
vacuumIndicates the pressure in the
inlet circuit in mbar.

13B-126V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK (CONTINUED 4)
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Sensor
voltagePR077:EGR valve
position
sensor voltage0.5 V < PR077 < 4.8 VIn the event of a fault, apply the
interpretation of fault DF209
EGR valve position sensor
circuit (not applicable to
K9K796 Euro 2).
PR344:Manifold
pressure
sensor voltageShows the voltage supplied by the
computer to feed the inlet pressure
sensor in volts.In the event of a fault, apply the
interpretation of fault DF089
Inlet manifold pressure
sensor circuit.
PR080:Rail pressure
sensor voltage0.5 V < PR080 < 4.5 V
Shows the voltage supplied by the
computer on the rail pressure
sensor in volts.
Default value: 4.5 V.If there is a fault, use the
interpretation of fault DF007
Rail pressure sensor circuit.
PressurePR037:Refrigerant
pressure2 bar < PR037 < 27 bar
Shows the value of the refrigerant
fluid pressure in the system in bar.
Default value: 0 bar.In the event of a fault, apply the
interpretation of fault DF049
Refrigerant sensor circuit.
Air flowPR019:Linearised air
flowShows the linearised air flow in g/s.In the event of a fault, apply the
interpretation of fault DF056 Air
flow sensor circuit.
Engine
speedPR055:Engine speed0 rpm. NONE

13B-131V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK (CONTINUED 1)
NOTESOnly perform this conformity check after a complete check using the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine idling, warm engine, coolant temperature > 80°C.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Air
temperaturePR058:Air
temperatureGives the inlet air temperature
in °C. This information is
supplied by the air
temperature sensor
incorporated in the air
flowmeter.
Default value: 20°C.In the event of a problem, consult
the interpretation of fault DF056
Air flow sensor circuit.
Fuel
temperaturePR063:Fuel
temperatureCold = PR064 Coolant
temperature
Warm: 50°C
Gives the fuel temperature in
°C. This value is measured by
the fuel temperature sensor.
Default value: 30°C.If there is a fault, use the
interpretation of fault DF098 Fuel
temperature sensor circuit.
Atmospheric
pressurePR035:Atmospheric
pressureIndicates the atmospheric
pressure in mbar. The sensor
is built into the computer. In the event of inconsistency,
with the engine stopped and
ignition on, check that parameter
PR035PR312local
atmospheric pressure. Inlet manifold
vacuumPR312:Inlet manifold
vacuumIndicates the pressure in the
inlet circuit in mbar.
Battery voltagePR074:Battery voltage12 V < PR074 < 14.4 V.In the event of a fault, apply the
fault finding procedure for the
Charging circuit.

13B-134V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK (CONTINUED 4)
NOTESOnly perform this conformity check after a complete check using the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine idling, warm engine, coolant temperature > 80°C.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Sensor
voltagePR077:EGR valve
position
sensor voltage0.5 V < PR077 < 4.8 VIn the event of a fault, apply the
interpretation of fault DF209
EGR valve position sensor
circuit (not applicable to
K9K796 Euro 2).
PR344:Manifold
pressure
sensor voltageShows the voltage supplied by the
computer to feed the inlet pressure
sensor in volts.In the event of a fault, apply the
interpretation of fault DF089
Inlet manifold pressure
sensor circuit.
PR080:Rail pressure
sensor voltage0.5 V < PR080 < 4.5 V
Shows the voltage supplied by the
computer on the rail pressure
sensor in volts.
Default value: 4.5 V.In the event of a problem, apply
the interpretation of DF007 Rail
pressure sensor circuit.
PressurePR037:Refrigerant
pressure2 bar < PR037 < 27 bar
Shows the value of the refrigerant
fluid pressure in the system in bar.
Default value: 0 bar.In the event of a fault, apply the
interpretation of fault DF049
Refrigerant sensor circuit.
Air flowPR019:Linearised air
flowShows the linearised air flow in g/s.In the event of a fault, apply the
interpretation of fault DF056 Air
flow sensor circuit.