fuse box RENAULT KANGOO 2013 X61 / 2.G Diesel DCM 1.2 Injection Workshop Manual

13B-41
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF015
PRESENT
OR
STOREDMAIN RELAY CONTROL CIRCUIT
1.DEF: Permanent low level
2.DEF: Permanent high signal
NOTESConditions for applying the fault finding procedure to a stored fault:
Apply the fault finding procedure below if the fault is present or stored.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the main relay supply fuse in the engine compartment F02 (30 A), F11 (for Kangoo VLL) or F01 (30 A)
AutoFuse for Duster on the engine fuse and relay box, component code 597 or 260 (for Kangoo VLL) (see MR
388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the injection computer connector, component code 120, and of the
computer supply relay, component code 983 on the engine fuse and relay box.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3AA between components 120 and 983,
●3FB (or 3FB2) between components 120 and 983.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Replace the relay if the fault is still present.
DCM1.2_V08_DF015

13B-150
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP1 No dialogue with the computer
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty. If the
tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle, the cause
could be a faulty computer interfering on the multiplex network. Check the battery voltage and make the necessary
adjustments to obtain a correct voltage (9.5 V < Battery voltage < 17.5 V).
Carry out fault finding on the multiplex network using the diagnostic tool (see88B, Multiplexing).
Check the presence and the condition of the injection fuses in the engine fuse box.
Check the connection of the injection computer connectors, component code 120 and the condition of its
connections.
Check the injection computer earths (quality, oxidation, tightness of earth bolts on the battery terminal).
Check that the supply to the computer is correct:
●NH or N between the earth and component 120.
●AP29 or AP15 between components 1016 or 260 and 120.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
A
DCM1.2_V08_ALP01
DIESEL INJECTION
Fault finding – Fault Finding Chart