warning RENAULT KANGOO 2013 X61 / 2.G Lighting Workshop Manual

80D-3V1 MR-376-X76-80D000$010.mif
LIGHTING
Fault finding – Introduction80D
UCH
Vdiag No.: 0F
If the information obtained by the diagnostic tool requires the electrical continuity to be checked, connect
bornier Elé. 1622 or universal bornier Elé. 1681.
3. SAFETY INSTRUCTIONS
The safety instructions must be followed at all times when working on components, to avoid damage or injury:
– check the battery voltage to avoid incorrect operation of computer functions,
– use the appropriate toolsWARNING:
– All checks using bornier Elé. 1622 or Elé. 1681 must be performed with the battery disconnected.
– The bornier is only designed to be used with a multimeter. Never supply the test points with 12 V.

80D-4V1 MR-376-X76-80D000$020.mif
80D
UCH
Vdiag No.: 0F
Side lights:
The side lights are switched on directly using the lighting stalk, via the passenger compartment fuse and relay box.
This function lights all the side lights (front and rear) as well as the number plate lighting.
Dipped beam headlights:
The dipped beam headlights are switched on directly using the lighting stalk, via the passenger compartment fuse
and relay box.
This function lights only the two bulbs providing the dipped headlights function.
Main beam headlights:
The main beam headlights are switched on directly using the lighting stalk, via the passenger compartment fuse and
relay box.
This function lights only the two bulbs providing the main beam headlights function.
Rear fog light:
The rear fog light is switched on directly using the lighting stalk, via the passenger compartment fuse and relay box.
This function lights only the rear fog lights.
Hazard warning lights:
The "hazard warning lights illumination request" signal from the hazard warning lights switch is sent to the UCH,
which controls the hazard warning lights.
This function lights only the hazard warning lights. The UCH also manages the illumination of the hazard warning
lights in the event of impact detection.
Indicators:
The "left-hand or right-hand indicators illumination request" signal initiated by the driver using the lighting stalk is
sent to the UCH, which controls the left-hand and right-hand indicators.
LIGHTING
Fault finding – Role of components

80D-5V1 MR-376-X76-80D000$030.mif
80D
UCH
Vdiag No.: 0F
Indicator lights
• List of system components and associated component codes:
• Indicator lights diagram645Passenger compartment electrical control unit
260Passenger compartment fuse box and relay
125Hazard warning lights switch
172Rear right-hand light
173Rear left-hand light
255Front right-hand indicator light
256Front left-hand indicator light
267Right-hand repeater
268Left-hand repeater
209Lighting stalk
LIGHTING
Fault finding – Operating diagram

80D-12V1 MR-376-X76-80D000$040.mif
LIGHTING
Fault finding – Function80D
UCH
Vdiag No.: 0F
The LIGHTING function is divided into two sub-functions: lighting control and lighting power.
This function is managed directly, without the intervention of the UCH.
1. Lighting control
Operated by the driver
The UCH receives the driver's request via the steering column switches and the hazard warning lights button.
View the statuses of the available commands (see Status summary table).
2. Lighting power
The UCH manages the supply to the interior lighting, the heating and air conditioning system indicator lights, and the
central locking indicator lights.
The UCH manages the supply to the indicators.
The functioning of the lights supplied by the UCH can be checked using the actuator commands AC022 Left-hand
indicator, AC023 Right-hand indicator, and AC145 Front courtesy lights.
Functions available and operating mode
– Hazard warning lights illuminated upon impact:
In the event of an impact detected by the airbag computer, this function sends an activation request to the UCH to
illuminate the hazard warning lights.
The function of illuminating the hazard warning lights in the event of an impact is configured using SC008 UCH type
(See 87B, Passenger compartment connection unit). This function is viewed using LC009 Hazard warning
lights illuminated upon impact.

80D-13V1 MR-376-X76-80D000$050.mif
80D
UCH
Vdiag No.: 0F
Configurations of the lighting function in the UCH
Configuration readings available using the diagnostic tool:
• Check the configurations in the Read configurations menu Equipment required:
CLIP diagnostic tool
Configuration
readingName of configuration Option Configuration
LC009Hazard warning lights
illuminated upon impactWITH OR WITHOUT
SC008 UCH type (See 87B,
Passenger compartment
connection unit) LC047 Timed courtesy light WITH OR WITHOUT
LC168 Courtesy light timerAUTHORISED or
PROHIBITED
LIGHTING
Fault finding – Configuration

80D-14V1 MR-376-X76-80D000$060.mif
80D
UCH
Vdiag No.: 0F
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values indicated in this conformity check are given as examples.
Test conditions: Engine stopped, ignition on.
FunctionParameter or status
Checked or actionDisplay and Notes Fault finding
Lighting
controlET484Side lights signalPresent during command
for side lights In the event of a fault, apply
the interpretation of status
ET484.
ET485Hazard warning
lights signalPresent during command
for hazard warning lightsIn the event of a fault, apply
the interpretation of status
ET485.
ET486Right-hand
direction indicator
signalPresent during command
for right-hand direction
indicatorIn the event of a fault, apply
the interpretation of status
ET486.
ET487Left-hand direction
indicator signalPresent during command
for left-hand direction
indicatorIn the event of a fault, apply
the interpretation of status
ET487.
UCH_V0F_CCONF
LIGHTING
Fault finding – Conformity check

80D-15V1 MR-376-X76-80D000$070.mif
80D
UCH
Vdiag No.: 0F
Tool status Diagnostic tool title
ET484Side lights signal
ET485Hazard warning lights signal
ET486Right-hand direction indicator signal
ET487Left-hand direction indicator signal
LIGHTING
Fault finding – Status summary table

80D-17
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-80D000$080.mif
LIGHTING
Fault finding – Interpretation of statuses80D
UCH
Vdiag No.: 0F
ET485HAZARD WARNING LIGHTS SIGNAL
NOTESThere must be no present or stored faults.
Activate the hazard warning lights switch.
The status should be PRESENT.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
"ABSENT"
Check for the presence and condition of supply fuse F31 (10 A) on the passenger
compartment fuse and relay box, component code 260 (see MR 374 Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the hazard warning lights switch connector,
component code 125.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the operation of the hazard warning lights control.
Check the continuity between the following connections:
•64Q and MK of component 125,
•MK and 64D of component 125.
If the connection or connections are faulty and if there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the wiring, otherwise replace it.
Check the continuity of the following connection:
•64D between components 125 and 645.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
UCH_V0F_ET485

80D-18
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-80D000$080.mif
LIGHTING
Fault finding – Interpretation of statuses80D
UCH
Vdiag No.: 0F
ET485
CONTINUEDHAZARD WARNING LIGHTS SIGNAL
"ABSENT"
Check the continuity of the following connection:
•MK of component 125:
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
• Check the insulation, continuity and the absence of interference resistance on
the following connection:
•64Q between components 125 and 645.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, contact the techline.

80D-27
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-80D000$120.mif
80D
UCH
Vdiag No.: 0F
ALP 2 The direction indicator lights do not work
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check the bulbs.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Press the hazard warning lights switch and check that status ET485 Hazard warning lights signal is PRESENT;
if not, refer to the interpretation of this status.
Activate the right-hand or left-hand indicator and check that ET486 Right-hand indicator signal and ET487 Left-
hand indicator signal are PRESENT. If not, refer to the interpretation of these statuses.
Check the condition of the UCH connector, component code 645.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity of the following connections:
•64C between components 645 and 256, then 173, then 268,
•64D between components 645 and 255, then 172, then 267.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ALP02
LIGHTING
Fault finding – Fault Finding Chart