ignition RENAULT KANGOO 2013 X61 / 2.G Passenger Comparment Connection Unit User Guide

87B-19
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
87B
UCH
VDiag No.: 0F
ET004+ 12 VOLTS AFTER IGNITION
NOTESSpecial note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
ET004: "NO" with the ignition on
Check fuse F15 (20 A) in the passenger compartment fuse and relay box, component code 260 (see MR 374,
Mechanical, 81C, Fuses, Fuses: List and location of components).
Using a multimeter, check for + 12 V after ignition on connection AP7 of the UCH connector, component code 645.
Using a multimeter, check for + 12 V on connection BP10 of the UCH connector, component code 645.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If there is no voltage, check the continuity and the insulation to earth on the following connection:
●AP7 between components 645 and 260.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
ET004: "YES" with the ignition off
Using a multimeter, check that there is no +12 V with the ignition off on connection AP7 of the UCH connector,
component code 645.
If the fault is still present, contact the techline.
UCH_V0F_ET004
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses

87B-20
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET127IMMOBILISER WARNING LIGHT
NOTESThe immobiliser warning light status should be OFF after the + after ignition feed is
switched on.
The immobiliser warning light status should be ON when the key is not in the ignition
switch.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check the connection and condition of the instrument panel connector, component code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the UCH connector, component code 645.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using a multimeter, check the continuity and insulation of the following connection:
●87H between components 645 and 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ET127

87B-22
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET549ENGINE IMMOBILISER ACTIVE
NOTESThe immobiliser active status should change to inactive when the + after ignition is
switched on.
The immobiliser status should be active when the key is absent from the ignition switch.
ET549: YES despite the presence of a key in the ignition switch and + after ignition feed
Check that there is no fault before dealing with this status.
Check that status ET004 + 12 V After ignition is YES with the ignition on.
Deal with status ET004 if it is NOwith the ignition on.
Check status ET185 Key code received and status ET184 Key code valid with the ignition on.
If statuses ET185 and ET184 are YES, perform fault finding on the injection computer.
If status ET185 is NO, deal with this status first.
If status ET185 is YES and status ET184 is NO, deal with status ET184 first.
If the fault is still present, contact the techline.
UCH_V0F_ET549

87B-27
AFTER REPAIRCarry out a road test, followed by a check with the diagnostic tool.
V1 MR-376-X76-87B000$130.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of commands87B
UCH
VDiag No.: 0F
VP004ENTERING THE VIN
NOTESThis command permits manual entry of the vehicle's VIN into the computer.
Use this command each time the computer is replaced.
The vehicle identification number is indicated on the manufacturer's plate on the
right-hand side door pillar.
Procedure for writing the VIN
– establish dialogue with the UCH,
– select the repair mode menu,
– select the other settings menu,
– select line VP004 Write VIN,
– enter the VIN twice,
– exit fault finding mode,
– switch off the ignition,
– wait for the end of power latch,
– re-read the VIN using ID019 VIN Code in the Identification menu for confirmation.
UCH_V0F_VP004

87B-32
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-87B000$150.mif
87B
UCH
VDiag No.: 0F
ALP1 No dialogue with the computer
NOTESSpecial note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Test the diagnostic tool on another vehicle which is in perfect working order.
Check:
– the connection between the diagnostic tool and the diagnostic socket, component code 225 (cable in good
condition),
– the engine and passenger compartment fuses (see MR 374, Mechanical, 81C, Fuses, Fuses: List and
location of components).
Check for + 12 V before ignition on the following connection:
●BP10 of component 225.
Check for + 12 V after ignition on the following connection:
●AP10 of component 225.
Check for an earth on the following connections:
●MK and NA of component 225.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity of the following connection:
●HK between components 225 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Connect the bornier and check the insulation, continuity and absence of interference resistance on the
following connections:
●BP10 between components 645 and 260,
●AP7 between components 645 and 260,
●NA between component 645 and earth,
●HK between components 645 and 225.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
UCH_V0F_ALP01
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Fault Finding Chart