ignition RENAULT KANGOO 2013 X61 / 2.G Passenger Comparment Connection Unit Workshop Manual

87B-6V1 MR-376-X76-87B000$040.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Configuration87B
UCH
VDiag No.: 0F
CONFIGURATION OF THE UCH COMPUTER
●With the ignition on, establish dialogue with the UCH computer.
●In the Repair Mode menu, go to the Configuration tab.
Choose the scenario: SC008 UCH type and follow the instructions on the diagnostic tool.
Single Door Opening (SDO*) function:
Configuration CF272 SDO* enables the activation or deactivation of the Single Door Opening function.
There are two possible options for the configuration of this function:
WITH:
An initial press of the button unlocks the driver's door.
Pressing the button for a second time unlocks the whole vehicle after a predefined time.
WITHOUT:
Pressing the button once only unlocks the whole vehicle.
Check the configuration has been correctly stored using the Configuration reading menu.
*SDO: Single Door Opening

87B-10
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$070.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of faults87B
UCH
VDiag No.: 0F
DF271
PRESENTUCH INTERNAL ELECTRONIC FAULT
NOTESFault declared present when the ignition is switched off.
If the fault is still present, contact the Techline.
UCH_V0F_DF271P

87B-11
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$070.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of faults87B
UCH
VDiag No.: 0F
DF273
PRESENT
OR
STOREDIMPACT CONNECTION
NOTESSpecial notes:
The fault is present 8 seconds after the ignition is switched on and becomes stored
after the ignition is switched off.
Note:
If this fault is present, the door locking function while driving is inhibited.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Perform fault finding on the airbag function (see 88C, Airbags and pretensioners).
Check the connection and condition of the UCH connectors, component code 645.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
●60BR between components 645 and 756.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline
UCH_V0F_DF273

87B-12V1 MR-376-X76-87B000$080.mif
87B
UCH
VDiag No.: 0F
MAIN SCREEN
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Engine
immobiliserET549:Immobiliser activeNOIn the event of a fault, apply
the interpretation of status
ET549.
Blank UCH ET008:Blank UCHNOIn the event of a fault, apply
the scenario SC004 Program
UCH.
SupplyPR001:Battery voltage12 V < X < 12.5 VIn the event of a fault, run
fault finding on the charging
circuit (see Technical Note
6014A, Checking the
charging circuit).
ET004:+ 12V after ignition
feedYESIn the event of a fault, apply
the interpretation of status
ET004.
ET091:Engine runningNOIn the event of a fault,
perform a test on the injection
computer (see 13B, Diesel
injection or 17B, Petrol
injection).
Speed PR008:Vehicle speedX in km/hIn the event of a fault,
perform a test on the vehicle
speed or ABS computer (see
38C, Anti-lock braking
system).
UCH_V0F_CCONF
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check

87B-13V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: ACCESS - SAFETY
SUB-FUNCTION: ACCESS
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Supply ET004:+ 12V after
ignition feedYESIn the event of a fault, apply
the interpretation of status
ET004.
Speed PR008:Vehicle speedX in mph (km/h)In the event of a fault,
perform a test on the vehicle
speed or ABS computer (see
38C, Anti-lock braking
system).
Opening
elementsET489:Front doorsOpen when the front doors
are open.In the event of a fault, apply
the interpretation of status
ET489.
ET551:Rear doors or
luggage
compartmentOpen when rear doors or
luggage compartment are
open.In the event of a fault, apply
the interpretation of status
ET551.

87B-14V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: ACCESS - SAFETY
SUB-FUNCTION: STARTING
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Supply ET004:+ 12V after
ignition feedYESIn the event of a fault,
apply the interpretation of
status ET004.
Opening
elementsET183:Key already
programmed for
the vehicleYESIn the event of a fault,
apply the interpretation of
status ET183 (see 82D,
Access – Security).
ET184:Valid key codeYES when the ignition is
switched onIn the event of a fault,
apply the interpretation of
status ET184 (see 82D,
Access – Security).
Engine
immobiliserET549:Immobiliser
activeNOIn the event of a fault,
apply the interpretation of
status ET549.
Immobiliser
warning lightET127:Immobiliser
warning lightOFFIn the event of a fault,
apply the interpretation of
status ET127.
KeyPR056:Number of keys
allocated1 to 4In the event of a fault,
apply the interpretation of
status PR056 (see 82D,
Access – Security).
ET185:Key code
receivedYES when the ignition is
switched onIn the event of a fault,
apply the interpretation of
status ET185 (see 82D,
Access – Security).

87B-15V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: LIGHTING
SUB-FUNCTION: LIGHTING CONTROL
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Side lights ET484:Side lights signalPresent when the side lights
are illuminated.In the event of a fault, apply
the interpretation of status
ET484 (see 80D, Lighting).
Direction
indicatorsET485:Hazard warning
lights signalPresent when the hazard
warning lights are
illuminated.In the event of a fault, apply
the interpretation of status
ET485 (see 80D, Lighting).
ET486:Right-hand
direction indicator
signalPresent when the right-hand
indicator is controlled.In the event of a fault, apply
the interpretation of status
ET486 (see 80D, Lighting).
ET487:Left-hand
direction indicator
signalPresent when the left-hand
indicator is controlled.In the event of a fault, apply
the interpretation of status
ET487 (see 80D, Lighting).

87B-16V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: WIPING
SUB-FUNCTION: WIPER CONTROL
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Supply ET004:+ 12V after
ignition feedYESIn the event of a fault,
apply the interpretation of
status ET004.
Park positionET027:Windscreen
wiper park
positionActive when the wiper
control is in the intermittent
position each time the
wiper stops.In the event of a fault,
apply the interpretation of
fault ET097 Windscreen
wiper park position (see
85A, Wiping - Washing).
ET097:Rear screen
wiper park
positionActive when the wiper
control is in the intermittent
position each time the
wiper stops.In the event of a fault,
apply the interpretation of
fault DF040 Rear screen
wiper park position (see
85A, Wiping - Washing).
Windscreen wiper
speed settingET558:Windscreen
wiper speed
setting selectionYes when the wiper control
is in the intermittent
position.In the event of a fault,
apply the interpretation of
status ET558 (see 85A,
Wiping - Washing).

87B-17V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: WIPING (CONTINUED)
SUB-FUNCTION: WIPER CONTROL
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Wiping - Washing
signalsET555:Rear screen
wiper signalPresent when the rear
screen wiper is working.In the event of a fault,
apply the interpretation of
status ET555 (see 85A,
Wiping - Washing).
ET492:Windscreen
washer signalPresent when the
windscreen washer is
working.In the event of a fault,
apply the interpretation of
status ET492 (see 85A,
Wiping - Washing).
ET557:Rear screen
washer signalPresent when the rear
screen washer is working.In the event of a fault,
apply the interpretation of
status ET557 (see 85A,
Wiping - Washing).
Supply PR001: Battery voltage12 V < X < 12.5 VIn the event of a fault, run
fault finding on the charging
circuit (see Technical Note
6014A, Checking the
charging circuit).

87B-18V1 MR-376-X76-87B000$090.mif
87B
UCH
VDiag No.: 0F
Tool status Diagnostic tool name
ET004+ 12 V after ignition feed
ET008UCH blank
ET091Engine running
ET127Immobiliser warning light
ET489Front doors
ET549Immobiliser active
ET551Rear doors or boot
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Status summary table