lock RENAULT KANGOO 2013 X61 / 2.G Passenger Comparment Connection Unit Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: KANGOO, Model: RENAULT KANGOO 2013 X61 / 2.GPages: 33, PDF Size: 0.22 MB
Page 5 of 33
87B-5V1 MR-376-X76-87B000$040.mif
87B
UCH
VDiag No.: 0F
UCH CONFIGURATIONS
The configuration options for the UCH are:
*RAID: Renault Anti-Intruder Device.
*CPE: Electric central door locking.
SDO*: Single Door Opening.Title and position on the diagnostic tool Configuration
Illumination of hazard warning lights upon impact (LC009)
SC008 UCH type Timed courtesy light (LC047)
Courtesy light timer (LC168)
Key type (LC097)
Airbag (LC113)
Automatic relocking (LC012)
Authorisation of RAID* function by diagnostic tool (LC170)
Radio frequency function (LC171)
Type of CPE* button (LC172)
Rear screen wiper (LC064)SC008 UCH type
SDO* (LC186)CF272 "SDO*"
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Configuration
Page 6 of 33
87B-6V1 MR-376-X76-87B000$040.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Configuration87B
UCH
VDiag No.: 0F
CONFIGURATION OF THE UCH COMPUTER
●With the ignition on, establish dialogue with the UCH computer.
●In the Repair Mode menu, go to the Configuration tab.
Choose the scenario: SC008 UCH type and follow the instructions on the diagnostic tool.
Single Door Opening (SDO*) function:
Configuration CF272 SDO* enables the activation or deactivation of the Single Door Opening function.
There are two possible options for the configuration of this function:
WITH:
An initial press of the button unlocks the driver's door.
Pressing the button for a second time unlocks the whole vehicle after a predefined time.
WITHOUT:
Pressing the button once only unlocks the whole vehicle.
Check the configuration has been correctly stored using the Configuration reading menu.
*SDO: Single Door Opening
Page 11 of 33
87B-11
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$070.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of faults87B
UCH
VDiag No.: 0F
DF273
PRESENT
OR
STOREDIMPACT CONNECTION
NOTESSpecial notes:
The fault is present 8 seconds after the ignition is switched on and becomes stored
after the ignition is switched off.
Note:
If this fault is present, the door locking function while driving is inhibited.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Perform fault finding on the airbag function (see 88C, Airbags and pretensioners).
Check the connection and condition of the UCH connectors, component code 645.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
●60BR between components 645 and 756.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline
UCH_V0F_DF273
Page 12 of 33
87B-12V1 MR-376-X76-87B000$080.mif
87B
UCH
VDiag No.: 0F
MAIN SCREEN
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Engine
immobiliserET549:Immobiliser activeNOIn the event of a fault, apply
the interpretation of status
ET549.
Blank UCH ET008:Blank UCHNOIn the event of a fault, apply
the scenario SC004 Program
UCH.
SupplyPR001:Battery voltage12 V < X < 12.5 VIn the event of a fault, run
fault finding on the charging
circuit (see Technical Note
6014A, Checking the
charging circuit).
ET004:+ 12V after ignition
feedYESIn the event of a fault, apply
the interpretation of status
ET004.
ET091:Engine runningNOIn the event of a fault,
perform a test on the injection
computer (see 13B, Diesel
injection or 17B, Petrol
injection).
Speed PR008:Vehicle speedX in km/hIn the event of a fault,
perform a test on the vehicle
speed or ABS computer (see
38C, Anti-lock braking
system).
UCH_V0F_CCONF
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check
Page 13 of 33
87B-13V1 MR-376-X76-87B000$080.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Conformity check87B
UCH
VDiag No.: 0F
FUNCTION: ACCESS - SAFETY
SUB-FUNCTION: ACCESS
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Supply ET004:+ 12V after
ignition feedYESIn the event of a fault, apply
the interpretation of status
ET004.
Speed PR008:Vehicle speedX in mph (km/h)In the event of a fault,
perform a test on the vehicle
speed or ABS computer (see
38C, Anti-lock braking
system).
Opening
elementsET489:Front doorsOpen when the front doors
are open.In the event of a fault, apply
the interpretation of status
ET489.
ET551:Rear doors or
luggage
compartmentOpen when rear doors or
luggage compartment are
open.In the event of a fault, apply
the interpretation of status
ET551.
Page 21 of 33
87B-21
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET489FRONT DOORS
NOTESCheck that no fault is present.
Open the front doors one after another.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check that, for each front door open, status ET489 is OPEN or for each front door closed, the status is CLOSED.
Check the connection and wiring of the driver's door rabbet switch, component code 180 and the passenger's door
rabbet switch, component code 181.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
●13A between components 180 and 645,
●13N or 13A between components 181 and 645,
●MK between component 180 and earth,
●MF between component 181 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity between the two connections of the door rabbet switches.
Pull the handle to open the lock and check that there is no longer any continuity between the two connections.
Check that the lock engages into the striker plate properly.
If the fault is still present, contact the techline.
UCH_V0F_ET489
Page 23 of 33
87B-23
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET551REAR DOORS OR LUGGAGE COMPARTMENT
NOTESCheck that no fault is present.
Open the rear doors one after another, then open the luggage compartment.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check that when one of the rear doors or the tailgate is opened, status ET551 is OPEN and that when the rear
doors or tailgate are closed, status ET551 is CLOSED.
Check the connection and wiring of the rabbet switch on the rear right-hand door, component code 178, the rabbet
switch on the rear left-hand door, component code 179 and of the tailgate opening switch, component code 560.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
●13N or 13A between components 179 and 645,
●13N or 13A between components 178 and 645,
●MG between component 179 and the earth,
●MF between component 178 and earth,
●MG between component 560 and earth,
●13N or 13A between components 560 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity between the two connections of the rabbet switches for the doors and the tailgate.
Pull the handle to open the lock and check that there is no longer any continuity between the two connections.
Check that the lock engages into the striker plate properly.
If the fault is still present, contact the techline.
UCH_V0F_ET551