ignition RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Owners Manual

17B-186V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR055ENGINE SPEED
PA R A M E T E R
DEFINITIONThis parameter indicates the engine's rotational speed in rpm.
Conformity check with engine stopped and ignition on.
With the ignition on the value must be 0 rpm.
In the event of a fault, apply interpretation of DF120 Engine speed sensor signal.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed, the value must be  750 rpm.
In the event of a fault, apply the interpretation of DF120.
V42_V04_PR055/V42_V05_PR055/V42_V06_PR055/V42_V14_PR055/V42_V16_PR055/V42_V18_PR055

17B-187V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR059INLET AIR TEMPERATURE
PA R A M E T E R
DEFINITIONThis parameter indicates the air temperature in °C.
Conformity check with engine stopped and ignition on.
With the ignition on the inlet air temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF002 Air temperature sensor circuit.
Parameter PR059  PR064 Coolant temperature engine cold.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the inlet air temperature varies according to the engine coolant temperature.
In the event of a fault, refer to the interpretation of fault DF002.
V42_V04_PR059/V42_V05_PR059/V42_V06_PR059/V42_V14_PR059/V42_V16_PR059/V42_V18_PR059

17B-188V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR064COOLANT TEMPERATURE
PA R A M E T E R
DEFINITIONThis parameter indicates the engine coolant temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Conformity check with engine stopped and ignition on.
With the ignition on the coolant temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF001 Coolant temperature sensor circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the coolant temperature varies according to the engine temperature.
If there is a fault, refer to the interpretation of fault DF001.
V42_V04_PR064/V42_V05_PR064/V42_V06_PR064/V42_V14_PR064/V42_V16_PR064/V42_V18_PR064

17B-189V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR071COMPUTER SUPPLY VOLTAGE
PA R A M E T E R
DEFINITIONThis parameter indicates the computer supply voltage in volts.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C.
The voltage should be between:
9V In the event of a fault, run fault finding on the charging circuit (see 16A, Checking the charging circuit) and refer
to the interpretation of DF047 Computer supply voltage.
V42_V04_PR071/V42_V05_PR071/V42_V06_PR071/V42_V14_PR071/V42_V16_PR071/V42_V18_PR071

17B-190V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR089VEHICLE SPEED
PA R A M E T E R
DEFINITIONGives the vehicle speed in km/h.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C.
Carry out a road test, observing the vehicle speed on the instrument panel and the information given by the
diagnostic tool.
If there is an inconsistency between the two values, run complete fault finding on the ABS computer (see 38C,
ABS).
V42_V04_PR089/V42_V05_PR089/V42_V06_PR089/V42_V14_PR089/V42_V16_PR089/V42_V18_PR089

17B-191V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR097MOTORISED THROTTLE VALVE LOWER STOP PROGRAMMED VALUE
PA R A M E T E R
DEFINITIONThis parameter indicates the programmed throttle valve upper stop value as a %.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C
The value must be  9%.
In the event of a fault, apply the interpretation of ET051 Throttle stop programming.
V42_V04_PR097/V42_V05_PR097/V42_V06_PR097/V42_V14_PR097/V42_V16_PR097/V42_V18_PR097

17B-194
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*ocr = opening cyclic ratio
PR102CANISTER BLEED SOLENOID VALVE OCR*
PA R A M E T E R
DEFINITIONThis parameter indicates the canister bleed solenoid valve opening cyclic ratio in %.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C
The value must be between 0% and 100%.
V42_V04_PR102/V42_V05_PR102/V42_V06_PR102/V42_V14_PR102/V42_V16_PR102/V42_V18_PR102

17B-198
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR139RICHNESS ADAPTIVE OPERATION
PA R A M E T E R
DEFINITIONNo faults must be present.
Conformity check with the engine running and engine coolant temperature > 80°C
Check the sealing of the fuel vapour absorber bleed.
Repair if necessary.
With the engine warm in the idle speed regulation phase, look at parameter PR139.
– If the parameter goes to MAXIMUM stop, there is not enough fuel or too much air in the mixture.
– If the parameter goes to MINIMUM stop, there is too much fuel or not enough air in the mixture.
Check the cleanliness and correct operation of:
– petrol filter,
– petrol pump,
– fuel circuit,
–tank,
– air supply pipe,
– air filter,
– plugs.
Repair if necessary.
Check:
– the compressions,
– the valve clearance,
– the ignition.
Repair if necessary.
V42_V04_PR139/V42_V05_PR139/V42_V06_PR139/V42_V14_PR139/V42_V16_PR139/V42_V18_PR139

17B-199
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR147PEDAL POTENTIOMETER GANG 1 VOLTAGE
PA R A M E T E R
DEFINITIONThis parameter indicates the pedal potentiometer gang 1 voltage in volts.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C.
The value must be  0.72 V and varies according to the status of the pedal.
In the event of a fault, apply the interpretation of fault DF974 Pedal potentiometer circuit gang 1.
V42_V04_PR147/V42_V05_PR147/V42_V06_PR147/V42_V14_PR147/V42_V16_PR147/V42_V18_PR147

17B-200V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR148PEDAL POTENTIOMETER GANG 2 VOLTAGE
PA R A M E T E R
DEFINITIONThis parameter indicates the pedal potentiometer gang 2 voltage in volts.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C.
The value must be 0.52 V and varies according to the status of the pedal.
In the event of a fault, apply the interpretation of fault DF975 Pedal potentiometer circuit gang 2.
V42_V04_PR148/V42_V05_PR148/V42_V06_PR148/V42_V14_PR148/V42_V16_PR148/V42_V18_PR148