wiring diagram RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: KANGOO, Model: RENAULT KANGOO 2013 X61 / 2.GPages: 279, PDF Size: 1.29 MB
Page 34 of 279
17B-34
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF029
PRESENT OR
STOREDCYLINDER 4 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 4 injector, component code 196.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 4 injector, component code196 between connections3FB and 3CU.
If the resistance measured is not between 11 X 20 (K4M, D4D engines), 11.5 X 12.5 (F4R engine),
9.2 X 17 (K7M engine) or 14 X 15 (K4M engine on Duster): replace the cylinder 4 injector,
component code 196 (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting
).
Run command AC008 Cylinder 4 injector and check the operation of the injector with a listening test.
V42_V04_DF029/ V42_V05_DF029/V42_V06_DF029/V42_V14_DF029/V42_V16_DF029/V42_V18_DF029
Page 36 of 279
17B-36
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF038
PRESENT OR
STOREDCOMPUTER1.DEF: Internal electronic fault.
NOTESSpecial notes:
The OBD and Level 2 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Contact the Techline.
V42_V04_DF038/ V42_V05_DF038/V42_V06_DF038/V42_V14_DF038/V42_V16_DF038/V42_V18_DF038
Page 38 of 279
17B-38
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF047
PRESENT OR
STOREDCOMPUTER SUPPLY VOLTAGE1.DEF: Permanent high signal.
2.DEF: Permanent low level.
NOTESSpecial notes:
The OBD and Level 1 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Move the wiring harness between the injection computer, component code 120 and the battery, component code
107 to see if the status changes (Present Stored).
Look for any damage to the wiring harness and check the connection and condition of the battery, component code
107 and its connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Start the engine and check the battery voltage using PR071 Computer supply voltage is X 9V.
Stop the engine and check the charging circuit of the vehicle (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 16A,
Starting – Charging, Charging circuit: Checking).
If the fault is still present, contact the Techline.
V42_V04_DF047/ V42_V05_DF047/V42_V06_DF047/V42_V14_DF047/V42_V16_DF047/V42_V18_DF047
Page 39 of 279
17B-39
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF050
PRESENT OR
STOREDBRAKE SWITCH CIRCUIT
1.DEF: Inconsistent signal.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present after the ignition has been switched on and the brake pedal has
been depressed.
The fault appears after a fault on one of the two brake switch contacts.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
ET039 must be Released and ET799 Inactive.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
Remove the brake pedal switch, component code 160 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR
423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal
- Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical component controls,
Brake pedal: Removal - Refitting) and, without depressing the pedal, press sufficiently on the brake pedal switch
to seat it completely in its position.
Lock it by turning it an eighth of a turn.
With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL) and
65A. The value must be X > 10 M (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
With the brake pedal released, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL) and
5A, the value must be between 0 < X 1 (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
V42_V04_DF050/ V42_V05_DF050/V42_V06_DF050/V42_V14_DF050/V42_V16_DF050/V42_V18_DF050
Page 51 of 279
17B-51
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF078
PRESENT OR
STOREDMOTORISED THROTTLE CONTROL CIRCUIT
1.DEF: Motorised throttle general control fault
WARNING:
Never drive the vehicle without having confirmed that no faults involving the throttle valve are present.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is considered present if:
– the engine speed varies,
– the AC027 Motorised throttle command is activated.
Special notes:
OBD warning light and level 1 fault warning light illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the injection computer connector, component code 120 and the throttle
valve connector, component code 1076.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3AJB between components 120 and 1076,
–3AJC between components 120 and 1076.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline
V42_V04_DF078/ V42_V05_DF078/V42_V06_DF078/V42_V14_DF078/V42_V16_DF078/V42_V18_DF078
Page 52 of 279
17B-52V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF079
PRESENT OR
STOREDMOTORISED THROTTLE VALVE SERVO1.DEF: Motorised throttle rest position programming error
2.DEF: Values outside permitted tolerance
3.DEF: Incorrect position of throttle valve in safe mode
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present:
– switch on the powerlatch phase - switch off + after ignition feed and switch on the
+ after ignition feed again
Special notes:
OBD warning light and level 1 fault warning light illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the injection computer connector, component code 120 and the throttle
valve connector, component code 1076.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
If the fault is still present, manually check that the throttle valve rotates correctly.
Repair if necessary (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430
(Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 12A, Fuel mixture, Throttle valve: Cleaning).
Accelerate a couple of times and check that the values of PR538 Measured voltage gang 2 and PR539 Measured
voltage gang 1 vary according to acceleration.
If the fault is still present, disconnect the battery and the injection computer.
Check the insulation, continuity and absence of interference resistance of the following connections:
–3AJB between components 120 and 1076,
–3AJC between components 120 and 1076,
–3MO between components 120 and 1076,
–3MP between components 120 and 1076,
–3MN between components 120 and 1076,
–3MQbetween components 120 and 1076.
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring
If the throttle valve has been replaced, reinitialise the programming by running command RZ031 Throttle stop
programming.
If the fault is still present, contact Techline.
V42_V04_DF079/ V42_V05_DF079/V42_V06_DF079/V42_V14_DF079/V42_V16_DF079/V42_V18_DF079
Page 53 of 279
17B-53
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF080
PRESENT
OR STOREDCAMSHAFT DEPHASER CIRCUITCO: Open circuit
CC.0: Short circuit to earth
CC.1: Short circuit to +12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is considered present when the engine is running.
See the Wiring Diagrams Technical Note for Duster.
See Technical Note 6506A, Injection fault finding, Camshaft dephaser, ALP4 Electrical fault (status CO,
CC.1, CC.O) on the camshaft dephaser detected using Clip: DF080 "Camshaft dephaser circuit" or DF063
"Camshaft dephaser" (K4M and F4R 830 Clio III RS).
If the fault is still present, contact Techline.
V42_V04_DF080/V42_V05_DF080/V42_V06_DF080/V42_V14_DF080/V42_V16_DF080/V42_V18_DF080
Page 54 of 279
17B-54V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF081
PRESENT OR
STOREDCANISTER BLEED SOLENOID VALVE CIRCUITCO: Open circuit
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Special notes:
For CO and CC.1, the OBD warning light and level 1 fault warning light illuminate.
Check the cleanliness and condition of the connector of the injection computer, component code 120 and of the
connector of the fuel vapour absorber bleed solenoid valve, component code 371.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3FB between components 371 and 1047 (for Logan, Sandero, Duster) or 238 (for Thalia 2/Symbol 2, Kangoo
VLL) or 983 (for Clio II F 6),
–3BB between components 371 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for + 12 V on connection 3FB of component 371.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the operation of the canister bleed solenoid valve using command AC017 Canister bleed solenoid valve.
Measure the resistance of the fuel vapour absorber bleed solenoid valve, component code 371.
If the resistance of the fuel vapour absorber bleed solenoid valve is not between: 24 < X < 30 or 22 < X <
30 (Duster F4R and K4M engine) between 0°C and 40°C,
replace the fuel vapour absorber bleed solenoid valve,
component code 371 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR
430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 14A, Emission control, Fuel vapour absorber:
Removal - Refitting).
If the fault is still present, contact Techline.
V42_V04_DF081/ V42_V05_DF081/V42_V06_DF081/V42_V14_DF081/V42_V16_DF081/V42_V18_DF081
Page 55 of 279
17B-55V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF082
PRESENT OR
STOREDUPSTREAM OXYGEN SENSOR HEATING CIRCUITCO: Open circuit
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Special notes:
For CO and CC.1, the OBD warning light illuminates.
Check the condition of the supply circuit fuse for the upstream oxygen sensor, component code 887.
If the fuse is faulty, replace the fuse (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 81C, Fuses, Fuses: List and location
of components).
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
upstream oxygen sensor connector, component code 887.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
With the ignition on, check for + 12 V on connection 3FB of component 887.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3FB between components 1047 (for Logan, Sandero, Duster) or 238 (for Thalia 2/Symbol 2, Kangoo VLL) or
983 (for Clio II F 6) and 887,
–3GF between components 120 and 887.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If all the checks are correct, replace the upstream oxygen sensor, component code 887 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF082/ V42_V05_DF082/V42_V06_DF082/V42_V14_DF082/V42_V16_DF082/V42_V18_DF082
Page 56 of 279
17B-56V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF083
PRESENT OR
STOREDDOWNSTREAM OXYGEN SENSOR HEATING CIRCUITCO: Open circuit
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Special notes:
For CO and CC.1, the OBD warning light and level 1 fault warning light illuminate.
Check the condition of the fuse of the supply circuit for the downstream oxygen sensor, component code 242.
If the fuse is faulty, replace the fuse (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 81C, Fuses, Fuses: List and location
of components).
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
connector of the downstream oxygen sensor, component code 242.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
With the ignition on, check for + 12 V on connection 3FB of component 242.
Check the insulation, continuity and the absence of interference resistance of the following connection:
–3FB between components 1047 (for Logan, Sandero, Duster) or 238 (for Thalia 2/Symbol 2, Kangoo VLL) or
983 (for Clio II F 6) and 242,
–3GG between components 120 and 242.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If all the checks are correct, replace the downstream oxygen sensor, component code 242 (see MR 388 (Logan
and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF083/ V42_V05_DF083/V42_V06_DF083/V42_V14_DF083/V42_V16_DF083/V42_V18_DF083