charging RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Workshop Manual

17B-38
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF047
PRESENT OR
STOREDCOMPUTER SUPPLY VOLTAGE1.DEF: Permanent high signal.
2.DEF: Permanent low level.
NOTESSpecial notes:
The OBD and Level 1 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Move the wiring harness between the injection computer, component code 120 and the battery, component code
107 to see if the status changes (Present Stored).
Look for any damage to the wiring harness and check the connection and condition of the battery, component code
107 and its connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Start the engine and check the battery voltage using PR071 Computer supply voltage is X  9V.
Stop the engine and check the charging circuit of the vehicle (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 16A,
Starting – Charging, Charging circuit: Checking).
If the fault is still present, contact the Techline.
V42_V04_DF047/ V42_V05_DF047/V42_V06_DF047/V42_V14_DF047/V42_V16_DF047/V42_V18_DF047

17B-99
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF532
PRESENT OR
STOREDALTERNATOR CHARGE SIGNAL1.DEF: Voltage too low
2.DEF: Voltage too high
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Special notes:
the OBD warning light is on.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection.
–2K between components 103 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the check is correct, replace the alternator, component code 103 (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 16A,
Starting - Charging, Alternator: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF532/V42_V05_DF532/V42_V06_DF532/V42_V14_DF532/V42_V16_DF532/V42_V18_DF532

17B-180V2 MR-376-X76-17B050$120.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
OCR*: Opening cyclic ratioTool
ParameterDiagnostic tool title
PR002 Alternator charge
PR015Engine torque
PR030Accelerator pedal position
PR037Refrigerant pressure
PR041 Turbocharging pressure
PR055Engine speed
PR059 Inlet air temperature
PR064Coolant temperature
PR071 Computer feed voltage
PR084 Coolant temperature sensor voltage
PR089Vehicle speed
PR097Motorised throttle lower stop programmed value
PR098Upstream oxygen sensor voltage
PR099Downstream oxygen sensor voltage
PR102Canister bleed solenoid valve OCR*
PR118Measured throttle position gang 1
PR119Measured throttle position gang 2
PR138Richness correction
PR139 Operating adaptive richness
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR215 Sensor supply voltage no. 1
PR216 Sensor supply voltage no. 2
PR312Inlet manifold vacuum
PR313 Linearised manifold pressure
PETROL INJECTION
Fault finding – Parameter summary table

17B-182V2 MR-376-X76-17B050$120.mif
PETROL INJECTION
Fault finding – Parameter summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Refriger.*: refrigerant
Syncro*: Synchronisation
OCR*: Opening cyclic ratio
CS*: CamshaftTool
ParameterDiagnostic tool title
PR832Combustion misfiring counter
PR833Combustion misfiring counter
PR834Combustion misfiring counter
PR847Inlet air temperature sensor voltage
PR872Refriger.* pressure sensor voltage
PR876CS* dephaser solenoid valve control OCR*
PR877Estimated engine oil temperature
PR887Motorised throttle safe mode programmed value
PR931Raw turbocharging pressure
PR1026Crankshaft synchro.* loss counter
PR1029 Alternator power
PR1116LPG pressure
PR1129 Brake contact no.1 duration
PR1153 Brake contact no.2 duration
PR1198LPG temperature
PR1232Number of engine rotations

17B-189V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR071COMPUTER SUPPLY VOLTAGE
PA R A M E T E R
DEFINITIONThis parameter indicates the computer supply voltage in volts.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C.
The voltage should be between:
9V In the event of a fault, run fault finding on the charging circuit (see 16A, Checking the charging circuit) and refer
to the interpretation of DF047 Computer supply voltage.
V42_V04_PR071/V42_V05_PR071/V42_V06_PR071/V42_V14_PR071/V42_V16_PR071/V42_V18_PR071

17B-201V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR215SENSOR SUPPLY VOLTAGE NO. 1
PA R A M E T E R
DEFINITIONThis parameter indicates the supply voltage no. 1 of the sensors in Volts.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant temperature
> 80°C without electrical consumers.
The voltage of PR215 is approximately 5000 mV.
In the event of a fault, run fault finding on the charging circuit and consult the interpretation of DF011 Sensor
supply voltage no. 1.
V42_V04_PR215/V42_V05_PR215/V42_V06_PR215/V42_V14_PR215/V42_V16_PR215/V42_V18_PR215

17B-202V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR216SENSOR SUPPLY VOLTAGE NO. 2
PA R A M E T E R
DEFINITIONThis parameter indicates the supply voltage no. 2 of the sensors in Volts.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant temperature
> 80°C without electrical consumers.
The voltage of PR216 is approximately 5000 mV.
In the event of a fault, run fault finding on the charging circuit and consult the interpretation of DF012 Sensor
supply voltage no. 2.
V42_V04_PR216/V42_V05_PR216/V42_V06_PR216/V42_V14_PR216/V42_V16_PR216/V42_V18_PR216

17B-220
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 1 No dialogue with the computer
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Try to establish dialogue with a computer on another vehicle to make sure that the diagnostic tool is not faulty. If
the tool is not the cause and communication cannot be established with any other computer on the same vehicle,
it is possible that another computer is disrupting the multiplex network.
Check the voltage of the battery.
If the battery voltage is between 9.5 V and 17.5 V, run fault finding on the charging circuit.
– Check the presence and condition of the injection fuses on the UPC and in the engine fuse box.
– Check the connection of the computer connectors, component code 120.
– Check the injection computer earths (quality, oxidation, tightness of the earth bolts on the battery terminal).
– Check that the supply to the computer is correct:
–Earth on connection NH of component 120 (for Logan, Sandero, Duster, Kangoo VLL),
–Earth on connection N of component 120 (for Thalia 2/Symbol 2),
–Earth on connection NF of component 120 (for Clio II F 6)
–+ 12V on connection 3FB of component 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the diagnostic socket, component code 225 is correctly supplied:
–+ before ignition feed on connection BP56 of component 225 (for Logan, Sandero, Duster),
–+ before ignition feed on connection BP10 of component 225 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo
VLL),
–+ after ignition feed on connection AP10 of component 225,
– Earth on connections MAM and NC of component 225 (for Logan, Sandero, Duster
),
– Earth on connections N and M of component 225 (for Thalia 2/Symbol 2, Clio II F 6),
– Earth on connections NA and MK of component 225 (for Kangoo VLL).
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If dialogue has still not been established after these checks, contact the techline.
V42_V04_ALP1/V42_V05_ALP1/V42_V06_ALP1/V42_V14_ALP1/V42_V16_ALP1/V42_V18_ALP1
PETROL INJECTION
Fault finding – Fault Finding Chart

17B-251
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 2 Alternator signal module check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
With the engine running, check the alternator charge without any electrical consumers switched on using PR002
Alternator charge, then switch on the consumers and check the increase in PR002.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection.
–2K between components 103 and 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the check is correct, replace the alternator signal module, component code 103 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 16A, Starting - Charging, Alternator: Removal - Refitting).
If the fault is still present, contact the techline.
V42_V04_TEST2/V42_V05_TEST2/V42_V06_TEST2/V42_V14_TEST2/V42_V16_TEST2/V42_V18_TEST2