RENAULT MEGANE SCENIC 1995 Service Repair Manual

NON-SIDE OPENING ELEMENTS
Luggage compartment lid
48P
48-6
The peripheral play is adjusted via mountings (H) and
(B). See section 40 for the setting values.IMPORTANT:
Mountings (B1) and (H1) are used as chain guides and
only allow height adjustment.
For additional adjustment settings, these mountings
may be replaced by points (B2) and (H2) respectively.
The beading and the closure stiffness are adjusted at
the lock (I) and the closure striker plate (J), as well as
via the lower stops (K) and (L).
17515-1R
17514-1R1
16786R
D

NON-SIDE OPENING ELEMENTS
Luggage compartment lid
48P
48-7
SPECIAL FEATURE OF ADJUSTING THE LOWER
STOP
Position the lower stop (L) and the two bolts (M).
Leave the central bolt loose.
Close the cover.
Pull tab (1) to the exterior (the stop comes into contact
with the lower beading of the casing and allows play to
be eliminated).
Open the luggage compartment lid.
Cut the tab and tighten the central bolt.
NOTE: it is recommended that you order a new lower
stop (K) for this operation. However, it is possible to
use the old stop (without tab), but adjustment of the
lower section will be more difficult.
16878R
17516R
17516-1R
D

GENERAL
Tooling
50P
150GENERAL
Tooling
Special tool for removing the rear screen wiper arm.
Unclipping pliers.
"Fir-tree" clips and interior trim clips such as on
door panels, soundproofing mats and mudguard
mountings can be removed easily using these pliers.
Door window winder handles can also be removed
(first apply some pull-off tape to the main point with the
door lining so that this is not damaged during
removal).
The heads of the clips are not deformed and can
therefore be reused after removal due to the flat and
bevelled nose allowing easy access without damaging
the clips.
18174R99799S
50-1
A

NON-SIDE OPENING ELEMENT MECHANISMS
Rear screen and luggage compartment lid locks
52
152 NON-SIDE OPENING ELEMENT MECHANISMS
Rear screen and luggage compartment lid locks
REAR SCREEN LOCK
After folding the rear seats,
move the lug (A) using a locally manufactured tool
(welding rod), This operation requires the help of a
person outside the vehicle.LUGGAGE COMPARTMENT LID LOCK
After removing the trim (section 73-A),
move lug (B) using a small screwdriver. NOTE: it is possible to unlock the rear screen lock
manually (without removing the trim) and the luggage
compartment lid lock (after removing the trim).
18080R16832R
52-1
A

NON-SIDE OPENING ELEMENT MECHANISMS
Rear screen and luggage compartment lid locks
52
52-2
REMOVING THE REAR SCREEN LOCK
After removing the trim (section 73-A),
disconnect connector (A).
Remove the two mounting screws (B).REMOVING THE REAR SCREEN STRIKER PLATE
Remove the two mounting screws.
The arrows indicate the adjustment options.
REFITTING
To refit, proceed in the reverse order to removal.
16831R1
16876S
A

NON-SIDE OPENING ELEMENT MECHANISMS
Rear screen and luggage compartment lid locks
52
52-3
REMOVING THE LUGGAGE COMPARTMENT LID
LOCK AND STOP
After removing the trim (section 73),
Remove:
– the two mounting bolts on the stop,
– the two mounting bolts on the lock.Disconnect the connector from the lock.
Using a flat-nosed pliers, apply light pressure to the
stop (C) and remove the lock.
REFITTING
Check that the lock operates correctly.
To refit, proceed in the reverse order to removal.
16785-1R
16877R
16786R1
A

NON-SIDE OPENING ELEMENT MECHANISMS
Rear screen and luggage compartment lid locks
52
52-4
REMOVING THE STRIKER PLATE AND THE PAD
ON THE BODY
Remove:
– the two striker plate bolts,
– the two pad bolts.
NOTE: the movement arrows indicate the adjustment
options.REFITTING
To refit, proceed in the reverse order to removal.
WARNING: If removing the striker plate and the pad
at the same time, the striker plate is no longer
supported.
16878S
A

NON-SIDE OPENING ELEMENT MECHANISMS
Luggage compartment lid exterior handle
52Luggage compartment lid exterior handle
REMOVAL
After removing the luggage compartment lid trim
(section 73-A),
remove the handle mounting bolt (A).
Disconnect the connector from handle (B).Remove the handle.
REFITTING
To refit, proceed in the reverse order to removal.
16785R
16787S
52-5
B

WINDOWS
Rear screen
54P
154WINDOWS
Rear screen
APPEARANCE AND OPENING CLEARANCES
A = 3 ± 2 mm
B = 5.5 ± 3 mm
IMPORTANT: it is vital that you fit the four self-
adhesive adjustment stops (part no. 82 00 048 913) to
the rear window surround, before bonding it.1 Location of the adjustment stops.
2 Adjustment stop
3 Adhesive tape
Refer to Technical Note 371A for information on how
to prepare and bond the windscreen.
18067R
18076R
16884-1R
54-1
A

EXTERIOR PROTECTION
Front bumper protection
55P
155EXTERIOR PROTECTION
Front bumper protection
REMOVAL
Remove:
– the lower mounting bolts (A),– the upper mounting bolts (B),
– the two bolts attached to the towing brackets (C).
17591R
16882R
16881R
55-1
A