horn RENAULT MEGANE SCENIC 1995 Service Repair Manual

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
E7J Engine
Remove the battery mounting bracket.
Disconnect the injection feed wire in the scuttle
panel as well as the starter motor feed.
98754R
Remove:
- the computer strap and secure it to the
engine,
- the wheels,
- the right hand and left hand mudguards,
98710R
- the brake calipers and secure them to the
body,
- catalytic converter,
- the two exhaust heat shields,
99612R
- the gear control on the gearbox side, turn it
over and secure to the exhaust pipe,
- the horn,
- the sub-frame-body tie rods,
- the front bumper.
PRJ1002
10-21

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
K7M engine
/ AT
- the heat shield from the exhaust manifold,
- the catalytic converter (disconnect the oxygen
sensor) and attach the exhaust pipe to the
body,
- the horn,
- the tie rod between the shock absorber
turrets,
- the air filter,
- the earth strap,
- the absolute pressure sensor,
- the expansion bottle and attach it to the
engine.
Disconnect:
- the accelerator cable and the kickdown switch
connector,
- the brake servo pipe,
- the relay plate and the engine connection unit
connectors,
98756R2
- the automatic transmission computer
connector,
- the canister pipe.Remove the battery mounting bracket.
Disconnect:
- the injection feed wire in the scuttle panel
and the starter feed wire,
- the fuel supply and return pipes using tool
Mot. 1311-06, unclipping them from their
mounting,
99461R
- the heater hoses on the thermostat.
Unclip the radiator and hold it to one side by
attaching it to the engine.
10-25

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
98710R
Remove:
- the front wheels,
- the right and left hand mudguards,
- the brake calipers and the ABS sensors (attach
them to the body),
- the sub-frame-body tie rods,
- the exhaust downpipe (disconnect the oxygen
sensor),
- the horn,
- the two exhaust heat shields,
99612R
- the gear control at the gearbox end (turn it
over and attach it to the exhaust pipe),
- the front bumper,
PRJ1002
- the air inlet sleeve, the air filter and its
mounting.
Disconnect:
- the relay plate and the engine connection unit
electrical connector,
98756R
10-30

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
- the front bumper,
PRJ1002
- the air inlet sleeve, the air filter and its
mounting,
- the exhaust downpipe,
- the two exhaust heat shields,
99612R
- the nut and eccentric bolt (1) (use a roll pin
punch) from the steering yoke after pushing
the protector back.
97390-1R
SPECIAL NOTES FOR VEHICLES FITTED WITH A
DRIVER’S AIRBAG
IMPORTANT
To avoid any risks of destroying the rotary switch
under the steering wheel, comply with the
following instructions:
• Before removing the steering column and the
rack, the steering wheel MUST be immobilised
with the wheels straight using a "steering
wheel locking" tool, throughout the whole
operation.
• Any doubts about whether the steering wheel
is centred means that the steering wheel will
have to be removed so that the centring
method described in section 88 "Airbag" can
be applied.
REMINDER: in this case, only qualified, trained
staff can carry out this operation.
- the gear control at the gearbox end (turn it
over and attach it to the exhaust pipe),
- the horn
- the expansion bottle (attach it to the engine)
- the earth strap
10-37

MANUAL GEARBOX
Gearbox (Removal - Refitting)
21
Remove the steering box mounting bolts.F
engine
98868-1R
Remove the mounting bolts of the power assisted
steering pipes from the sub-frame.
Secure the steering box to the side members.
Special notes for vehicles fitted with driver’s
AIRBAG
98836R1
97390-1R1
Remove the horn.
From above:
Secure the cooling assembly to the upper cross
member.
Remove the upper mounting bolt from the bum-
per then the bolts located in the wheel arches. Release the steering box and the steering column
(be careful not to damage the clip (C)).
ATTENTION :
to prevent any damage being done to the rota-
ting switch under the steering wheel, please fol-
low these instructions :
- before releasing the steering column and the
rack, the steering wheel MUST be immobilised,
wheels straight, using the "steering wheel
locking" tool throughout the duration of the
repair,
- any doubts regarding the correct centring of
the rotating switch means that the steering
wheel has to be removed so as to apply the
centring method as described in chapter 88
"AIR-BAG".
REMINDER: in this case, only qualified personnel
who have received specific training may under-
take this work.
21-16

- the heat shield from the exhaust manifold,
- the catalytic converter (disconnect the oxygen
sensor) and secure the exhaust pipe to the
body,
- the horn,
- the acoustic tie-rod between the shock
absorber turrets,
- the air filter,
- the earth strap,
- the absolute pressure sensor,
- the expansion bottle and secure it to the
engine.
Disconnect:
- the accelerator cable as well as the kickdown
switch connector,
- the brake servo pipe,
- the relay plate and the electrical connectors
from the engine connection unit,
AUTOMATIC TRANSMISSION
Automatic transmission (Removal - Refitting)
23
K7M
ENGINE
- the connector from the automatic transmission
computer,
- the canister pipe.
Remove the battery mounting bracket.
- the heating pipes on the thermostat.
Unclip the radiator and move it away by securing
it to the engine.
98756R
Disconnect:
- the injection supply wire located in the scuttle
panel as well as the starter motor supply,
- the fuel inlet and outlet hoses using Mot. 1311-
06, unclip them from their support,
99461R
23-16

GENERAL INFORMATION
Collision fault finding
40
40-14
GAUGE POINTS
Point M
Start point for checking points (A) and (B).
Point A
Sub-frame rear mounting.Point C
Front sub-frame front mounting.
It is necessary to remove the front bumper rear
protector and both horns to access this point.
Point H
Front end of front side member.
It is necessary to remove the engine undertray to
access this point.
16890R
16891R17512R
17512R1