fog light RENAULT PULSE 2012 1.G User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: PULSE, Model: RENAULT PULSE 2012 1.GPages: 352, PDF Size: 6.46 MB
Page 70 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
2-16Instruments and controls
Water-in-fuel-filte\or warning light (for
\fiesel engine mo\fel)
\bf the water-in-fuel-filt\oer warning light illuminates while
the engine is running, \frain the water from the fuel filter
promptly. (See “Fuel filter (\fiesel engine mo\fel)” (P.8-
15) .)
CAUTION:
Continuing vehicle operation without properly
draining could cause serious damage to the
engine.
\bND\bCATOR L\bGHTS
Cruise control on in\ficator light (if
equippe\f)
The cruise control on in\ficator light in\ficates the
activation of the cruise control system.
When the cruise control main switch is turne\f on, the
in\ficator light will illuminate, in\ficating the cruise
control system is in the stan\fby mo\fe. (See “Cruise
control” (P.5-28) .)
Cruise control/spee\f limiter set in\fi-
cator light (if equippe\f)
The cruise control/spee\f limiter set in\ficator light
in\ficates the status of the cruise control system.
When the vehicle spee\f is controlle\f by the cruise
control/spee\f limiter system, the in\ficator light illumi-
nates.
\bf the cruise control/spee\f limiter set in\ficator light
blinks while the engine is running, or while \friving, it
may in\ficate the cruise control/spee\f limiter system is not functioning properly an\f may nee\f servicing. Have
the system checke\f, an\f if necessary repaire\f, by a
RENAULT \fealer promptly. (See “Cruise control” (P.5-
28) an\f “Spee\f limiter (if equippe\f for Europe)” (P.5-
26) .)
Electronic Stability Program (ESP) off
in\ficator light (if equippe\f)
The Electronic Stability Program (ESP) off in\ficator
light illuminates when the ESP off switch is pushe\f to
the “OFF” position.
When the ESP off switch is pushe\f to the “OFF”
position, the ESP system is turne\f off.
\bf the ESP off in\ficator light an\f slip in\ficator light
illuminate while the engine is running or while \friving, it
may in\ficate the ESP system is not functioning
properly an\f may nee\f servicing. Have the system
checke\f, an\f if necessary repaire\f, by a RENAULT
\fealer promptly. (See “Electronic Stability Program
(ESP) System (if equippe\f for Europe)” (P.5-25) .)
Front fog lights in\ficator light (if
equippe\f)
The front fog lights in\ficator light illuminates when the
front fog lights are on. (See “Fog light switch” (P.2-
32) .)
Front passenger air bag status light (if
equippe\f)
The front passenger air bag status light locate\f on the
instrument panel will illuminate when the front passen-
ger air bag is turne\f off with the front passenger air
bag switch. When the front passenger air bag is turne\f
on, the front passenger air bag status light will turn off. For more \fetails, see “Supplemental Restraint System
(SRS)” (P.1-25) .
Glow plug in\ficator light (\fiesel engine
mo\fel)
When the ignition switch is in the “ON” position, the
glow plug in\ficator light illuminates an\f turns off after
the glow plugs have warme\f up.
\bf the glow plugs have alrea\fy warme\f up, the glow
plug in\ficator flashes briefly an\f then turns off.
High beam in\ficator light
The high beam in\ficator light illuminates when the
hea\flight high beam is “ON”. The in\ficator turns off
when the low beam is selecte\f. (See “Hea\flight an\f
turn signal switch” (P.2-29) .)
Low temperature in\ficator light (green)
*
The low temperature in\ficator light illuminates when
the engine coolant temperature is low.
When the ignition switch is in the “ON” position, the
low temperature in\ficator light illuminates an\f then
turns off after the engine coolant has warme\f up.
\bf the low temperature in\ficator light stays illuminate\f
after the engine has sufficiently warme\f up, it may
in\ficate the low temperature sensor in the engine
coolant system is not functioning properly an\f may
nee\f servicing. Have the system checke\f, an\f if
necessary repaire\f, by a RENAULT \fealer promptly.
& R Q G L W L R Q
Page 71 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Malfunction Indicator Light (MIL)
Wh\fn th\f ignition switch is in th\f “\bN” position, th\f
Malfunction Indicator Light (MIL) illuminat\fs. Aft\fr
starting th\f \fngin\f, th\f MIL turns off. This indicat\fs
that th\f \fngin\f control syst\fm is op\frational.
If th\f MIL illuminat\fs or blinks (if \fquipp\fd) whil\f th\f
\fngin\f is running, it may indicat\f that th\f \fngin\f
control syst\fm is not functioning prop\frly and may
n\f\fd s\frvicing. Hav\f th\f syst\fm ch\fck\fd, and if
n\fc\fssary r\fpair\fd, by a RENAULT d\fal\fr promptly.
Malfunction Indicator Light (MIL) on steady:
An \fngin\f control syst\fm malfunction has b\f\fn
d\ft\fct\fd. Hav\f th\f v\fhicl\f ch\fck\fd, and if n\fc\fssary
r\fpair\fd, by a RENAULT d\fal\fr promptly. You do not
n\f\fd to hav\f your v\fhicl\f tow\fd to th\f d\fal\fr.
Malfunction Indicator Light (MIL) blinking (if
equipped):
An \fngin\f misfir\f has b\f\fn d\ft\fct\fd which may
damag\f th\f \fngin\f control syst\fm. Hav\f th\f v\fhicl\f
ch\fck\fd, and if n\fc\fssary r\fpair\fd, by a RENAULT
d\fal\fr promptly.
To r\fduc\f or avoid possibl\f damag\f to th\f \fngin\f
control syst\fm wh\fn th\f MIL illuminat\fs or blinks:
.Avoid driving at sp\f\fds abov\f 70 km/h (43 MPH) .
. Avoid sudd\fn acc\fl\fration or d\fc\fl\fration.
. Avoid going up st\f\fp uphill grad\fs.
. Avoid carrying or towing unn\fc\fssary loads.
CAUTION:
.Continuing vehicle operation without proper
servicing of the engine control system could
lead to poor driveability, reduced fuel econ-
omy, and damage to the engine control system, which may affect the vehicle’s
warranty coverage.
. Incorrect setting of the engine control sys-
tem may lead to non-compliance of local
and national emission laws and regulations.
\bv\frdriv\f off indicator light (if
\fquipp\fd)
Th\f ov\frdriv\f off indicator light illuminat\fs wh\fn th\f
ov\frdriv\f is turn\fd \bFF. (S\f\f “Driving with Automatic
Transmission (AT)” (P.5-11) for th\f us\f of th\f ov\frdriv\f
off switch.)
R\far fog light indicator light (if
\fquipp\fd)
Th\f r\far fog light indicator light illuminat\fs wh\fn th\f
r\far fog light is on. (S\f\f “Fog light switch” (P.2-32) .)
S\fcurity indicator light (if \fquipp\fd)
Th\f s\fcurity indicator light blinks wh\fn th\f ignition
switch is in th\f “L\bCK”, “\bFF” or “ACC” position. This
function indicat\fs th\f Anti-Th\fft Syst\fm* \fquipp\fd on
th\f v\fhicl\f is op\frational.
(* immobiliz\fr)
If Anti-Th\fft Syst\fm is malfunctioning, this light will
r\fmain on whil\f th\f ignition switch is in th\f “\bN”
position. (S\f\f “S\fcurity syst\fm” (P.3-16) for additional
information.)
Slip indicator light (if \fquipp\fd)
Wh\fn th\f ignition switch is in th\f “\bN” position, th\f
slip indicator light illuminat\fs and th\fn turns off. This
indicat\fs that th\f V\fhicl\f Dynamic Control (VDC)
syst\fm or El\fctronic Stability Program (ESP) syst\fm is
op\frational.
Th\f slip indicator light blinks wh\fn th\f VDC or ESP
syst\fm is op\frating.
Wh\fn th\f indicator light blinks whil\f driving, th\f driving
condition is slipp\fry and th\f v\fhicl\f’s traction limit is
about to b\f \fxc\f\fd\fd.
If th\f VDC or ESP off indicator light and slip indicator
light illuminat\f whil\f th\f \fngin\f is running or whil\f
driving, it may indicat\f that th\f VDC or ESP syst\fm is
not functioning prop\frly and may n\f\fd s\frvicing. Hav\f
th\f syst\fm ch\fck\fd, and if n\fc\fssary r\fpair\fd, by a
RENAULT d\fal\fr promptly. (S\f\f “V\fhicl\f Dynamic
Control (VDC) syst\fm (if \fquipp\fd \fxc\fpt for Europ\f)”
(P.5-24) or “El\fctronic Stability Program (ESP) Syst\fm
(if \fquipp\fd for Europ\f)” (P.5-25) .)
Sp\f\fd limit\fr indicator light (if
\fquipp\fd)
This light illuminat\fs wh\fn th\f sp\f\fd limit\fr main
switch is push\fd. Th\f light turns off wh\fn th\f main
switch is push\fd again. Wh\fn th\f sp\f\fd limit\fr main
switch indicator light illuminat\fs, th\f sp\f\fd limit\fr
syst\fm is op\frational. (S\f\f “Sp\f\fd limit\fr (if \fquipp\fd
for Europ\f)” (P.5-26) .)
Instruments and controls2-17
& R Q G L W L R Q
Page 84 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
2-30Instruments and controls
position
Theposition turns on the headlights in addition to
the other lights\f
Headlight beam
\bIC3785
To turn on the high beam, push the lever towards the
front position*1\f
To turn off the high beam, return the lever to the neutral
position
*2\f
To flash the headlights, pull the lever towards the
rearmost position
*3\f The headlights can be flashed
even when the headlights are not on\f If equipped, when the lever is pulled towards the
rearmost position
*3after the ignition switch is
placed in the “OFF” or “LOCK” position, the headlight
will turn on and stay on for 30 seconds\f The lever can
be pulled 4 times for up to 2 minutes\f
Daytime light system (if equipped)
Even if the headlight switch is off, the daytime lights
will come on after starting the engine\f However, you
cannot change low beam to high beam when the light
switch is off\f
When the light switch is turned to the
position,
the headlight low beam will turn off\f
BATTERY \bAVER \bY\bTEM
The light reminder chime will sound if the driver’s door
is opened while the following improper operations
occur:
. The headlight switch is in either the
orposition, and the ignition switch in the “ACC”,
“OFF” or “LOCK” position\f
. The headlight switch is in the “AUTO” position and
the front or rear fog light (if equipped) is turned on
while the ignition switch is in the “ACC”, “OFF” or
“LOCK” position\f
Be sure to turn the headlight switch to the “OFF”
position when you leave the vehicle\f
Type A
When the headlight switch is in the
orposition while the engine is running, the lights will
automatically turn off after pushing the ignition switch
to the “ACC”, “OFF” or “LOCK” position and opening
the driver’s side door\f
When the headlight switch remains in either the
orposition after the lights automatically turn off,
the lights will turn on when the engine is started\f Type B
If the doors are closed and locked with the remote
controller, the Intelligent Key or the door request
switch (if equipped) while the headlight switch is in
either the
orposition, the battery saver
function will turn off the lights to prevent the battery
from being discharged\f The lights will turn on when the
doors are being opened\f
CAUTION:
Do not leave the lights on when the engine is not
running for extended periods of time to prevent
the battery from being discharged.
& R Q G L W L R Q
Page 86 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
2-32Instruments and controls
FRONT FOG LIGHTS
SIC3811Type A
SIC3813Type BTo tu\fn on the \b\font \bog lights, tu\fn the \bog light switch
to theposition with the headlight switch in theo\fposition.
To tu\fn o\b\b the \bog lights, tu\fn the \bog light switch to the
“OFF” position.
When the headlight switch is in the “AUTO” position (i\b
equipped):
. Tu\fning the \bog light switch to the
position
will tu\fn on the headlights, \bog lights and the othe\f
lights while the ignition switch is in the “ON” position o\f the engine is \funning.
REAR FOG LIGHT
SIC3812Type A
SIC4066Type B
SIC3814Type CTo tu\fn on the \fea\f \bog light, tu\fn the \bog light switch to
theo\fposition. The switch \fetu\fns to theposition automatically, and the \fea\f \bog light will
illuminate with the \b\font \bog lights. Make su\fe the
indicato\f light on the inst\fument panel illuminates.
To tu\fn o\b\b the \fea\f \bog light, tu\fn the \bog light switch to
the
position again. Make su\fe theindicato\f
light on the inst\fument panel tu\fns o\b\b.
To tu\fn o\b\b both the \b\font and \fea\f \bog lights, tu\fn the
\bog light switch to the “OFF” position.
When the headlight switch is in the “AUTO” position (i\b
equipped):
. Tu\fning the \bog light switch to the
position
will tu\fn on the headlights, \bog lights and the othe\f
lights while the ignition switch is in the “ON”
position o\f the engine is \funning.
The \fea\f \bog light should be used only when visibility is
se\fiously \feduced. [Gene\fally, to less than 100 m (328
\bt)]
FOG LIGHT SWITCH (if equipped)
& R Q G L W L R Q
Page 89 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Washer operation
To operate the washer, push the lever toward the front
of the vehi\fle*3until the desired amount of washer
fluid is spread on the rear window. The wiper will
automati\fally operate several times.
\bIC4127Type A
\bIC4145Type BThe rear window defogger swit\fh operates when the
ignition swit\fh is in the “ON” position.
The defogger is used to redu\fe the moisture, fog or
frost on the rear window surfa\fe and outside door
mirror surfa\fe (if equipped) to improve the rear view.
When the defogger swit\fh
*1is pushed, the indi\fator
light*2illuminates and the defogger operates for
approximately 15 minutes. After the preset time has
passed, the defogger will turn off automati\fally.
To turn off the defogger manually, push the defogger
swit\fh again.
CAUTION:
. When operating the defogger continuously,
be sure to start the engine. Otherwise, it may
cause the battery to discharge.
. When cleaning the inner side of the window,
be careful not to scratch or damage the
electrical conductors on the surface of the
window.
NOTE:
When the rear defogger is turned on, the Stop/
Start (Idling Stop) System (if equipped) will not
be activated.
Instruments and controls2-35
DEFOGGER SWITCH (if equipped)
& R Q G L W L R Q
Page 93 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4. Push the clock adjusting knob*1to adjust the
\finutes.
To advance the ti\fe, hold do\bn the knob
*1.
Wait at least 5 seconds for the second display “:”
to flash.
5. Push the clock adjusting knob
*1to reset the
second counter.
The selected values \bill be stored if no user input is
detected for 60 seconds, or can be reset by using the
adjusting knob.
SIC4436
The po\ber outlet is for po\bering electrical accessories
such as cellular telephone.
CAUTION:
. The outlet and plug may be hot during or
immediately after use.
. This power outlet is not designed for use
with a cigarette lighter unit.
. Do not use with accessories that exceed a 12
volt, 120W (10A) power draw. Do not use
double adapters or more than one electrical
accessory.
. Use power outlets with the engine running
to avoid discharging the vehicle battery.
. Avoid using power outlets when the air
conditioner, headlights or rear window de-
fogger is on.
. Before inserting or disconnecting a plug, be
sure to turn off the power switch of electrical
accessory being used and the ignition
switch.
. Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may open. .
Do not allow water to contact the outlet.
. When not in use, be sure to close the cap.
Instruments and controls2-39
POWER OUTLETS (if equipped)
& R Q G L W L R Q
Page 126 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4-6Heater and air conditioner, and audio system
.A visible mist may be seen coming f\fom the
ventilato\fs in hot, humi\b con\bitions as the ai\f is
coole\b \fapi\bly. This \boes not in\bicate a malfunc-
tion.
Dehumidified heating:
This mo\be is use\b to heat an\b \behumi\bify the ai\f.
1. Move the ai\f intake leve\f to the “
” position.
2. Tu\fn the ai\f flow cont\fol \bial to the “
” position.
3. Tu\fn the fan spee\b cont\fol “
” \bial to the
\besi\fe\b position.
4. Push the “A/C” button on. (The “A/C” in\bicato\f light will illuminate.)
5. Tu\fn the tempe\fatu\fe cont\fol \bial to the \besi\fe\b position between the mi\b\ble an\b the hot (\fight)
position.
Dehumidified defogging:
This mo\be is use\b to \befog the win\bows an\b
\behumi\bify the ai\f.
1. Move the ai\f intake leve\f to the “
” position.
2. Tu\fn the ai\f flow cont\fol \bial to the “
” position.
3. Tu\fn the fan spee\b cont\fol “
” \bial to the
\besi\fe\b position.
4. Push the “A/C” button on. (The “A/C” in\bicato\f light will illuminate.)
5. Tu\fn the tempe\fatu\fe cont\fol \bial to the \besi\fe\b position.
6. Tu\fn the si\be ventilato\fs to the si\be win\bows to \bef\fost o\f \befog the si\be mi\f\fo\fs.
AUTOMATIC AIR CONDITIONER
SAA2592
1. Win\bshiel\b \befogge\f “” button
2. Display
3. Rea\f win\bow \befogge\f “
” button (See
“Defogge\f switch” (P.2-35) .)
4. “AUTO” button
5. Tempe\fatu\fe cont\fol “
”/“” buttons
6. Fan spee\b cont\fol “
+” an\b “-”buttons
7. “OFF” button
8. “MODE” (ai\f flow cont\fol) button
9. Ai\f \feci\fculation “
” button
10. Outsi\be ai\f ci\fculation “
” button
11. “A/C” (Ai\f Con\bitione\f) button
Automatic ope\fation (AUTO)
The AUTO mo\be may be use\b yea\f-\foun\b as the
system automatically cont\fols constant tempe\fatu\fe, ai\f
flow \bist\fibution an\b fan spee\b afte\f the \besi\fe\b
tempe\fatu\fe is set manually.
To tu\fn off the heate\f an\b ai\f con\bitione\f, push the
“OFF” button. Cooling and dehumidified heating:
1. Push the “AUTO” button. (“AUTO” will appea\f on
the \bisplay.)
2. If the “A/C” in\bicato\f light \boes not illuminate, push the “A/C” button. (The “A/C” in\bicato\f light
will illuminate.)
3. Push the tempe\fatu\fe cont\fol “
”/“” but-
ton to set the \besi\fe\b tempe\fatu\fe.
4. If the in\bicato\f light on eithe\f the outsi\be ai\f ci\fculation “
” button o\f the ai\f \feci\fculation
“” button is illuminate\b, push the button with
the light illuminate\b to tu\fn the light off.
A visible mist may be seen coming f\fom the ventilato\fs
in hot, humi\b con\bitions as the ai\f is coole\b \fapi\bly.
This \boes not in\bicate a malfunction.
Heating (A/C off):
1. Push the “AUTO” button. (“AUTO” will appea\f on the \bisplay.)
2. If the “A/C” in\bicato\f light illuminates, push the “A/C” button. (The “A/C” in\bicato\f light will tu\fn
off.)
& R Q G L W L R Q
Page 127 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
3. Push the temperature control “”/“” \fut-
ton to set the desired temperature.
. \bo not set the temperature lower than the outside
air temperature. \boing so may cause the tem-
perature to not \fe controlled properly.
. If the windows fog up, use dehumidified heating
instead of the A/C off heating.
Dehumidified defrosting/defogging:
1. Push the front defogger “
” \futton. (The
“” indicator light will illuminate.)
2. Push the temperature control “
”/“” \fut-
ton to set the desired temperature.
. To remove frost from the outside surface of the
windshield quickly, set the temperature to a high
temperature and the fan speed to the maximum
level.
. After the windshield is cleared, push the front
defogger “
” \futton again. (The indicator light
will turn off.)
. When the front defogger “
” \futton is pushed,
the air conditioner will automatically turn on when
the outside air temperature is a\fove í28C (288F)
to defog the windshield. The air recirculation mode
will automatically turn off. The outside air circula-
tion mode “
” will \fe selected to improve the
defogging performance.
Manual operation
The manual mode can \fe used to control the heater
and air conditioner to your desired settings. (“MAN-
UAL” will appear on the display.)
To turn off the heater and air conditioner, push the
“OFF” \futton. Fan speed control:
Push the fan speed control “
”/“” \futton. Push
the “” \futton to increase the fan speed. Push the
“” \futton to decrease the fan speed.
Push the “AUTO” \futton to change the fan speed to
the automatic mode.
Air flow control:
Push the “MO\bE” \futton to change the air flow mode.
— Air flows from the center and side ventila- tors.
— Air flows from the center and side ventila-tors and foot outlets.
— Air flows mainly from the foot outlets
— Air flows from the defogger outlets and footoutlets.
Temperature control:
Push the temperature control “
”/“” \futton to
set the desired temperature. Push the “” \futton to
increase the temperature. Push the “” \futton to
decrease the temperature.
Outside air circulation:
Push the outside air circulation “
” \futton to draw
the air flow from outside the vehicle. (The “”
indicator light will illuminate.)
Air recirculation:
Push the air recirculation “
” \futton to circulate the
air flow inside the vehicle. (The “” indicator light
will illuminate.) Automatic air intake control:
If the indicator light on either the outside air circulation
“
” \futton or the air recirculation “” \futton is
illuminated, push the \futton with the light illuminated to
turn the light off. The automatic control is set \fetween
the outside air circulation “
” and air recirculation
“” modes.
SERVICING AIR CON\bITIONER
WARNING:
The air conditioner system contains refrigerant
under high pressure. To avoid personal injury,
any air conditioner service should be done only
by an experienced technician with the proper
equipment.
The air conditioner system in your vehicle is charged
with a refrigerant designed with the environment in
mind.
This refrigerant will not harm the earth’s ozone
layer. However, it may contri\fute in a small part to
glo\fal warming.
Special charging equipment and lu\fricant are required
when servicing your vehicle’s air conditioner. Using
improper refrigerants or lu\fricants will cause severe
damage to the air conditioner system. (See “Air
conditioner system refrigerant and lu\fricant” (P.9-4) .)
A RENAULT dealer will \fe a\fle to service your
environmentally friendly air conditioner system.
Heater and air conditioner, and audio system4-7
& R Q G L W L R Q
Page 128 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4-8Heater and air conditioner, and audio system
Air conditioner filter (if equipped)
\fhe air conditioner s\bstem is equipped with an air
conditioner filter which collects pollen. \fo make sure
the air conditioner heats defogs, and ventilates
efficientl\b, replace the filter according the specified
maintenance intervals listed in a separate maintenance
booklet. \fo replace the filter, contact a RENAUL\f
dealer.
\fhe filter should be replaced if the air flow decreases
significantl\b or if windows fog up easil\b when operating
the heater or air conditioner.AUDIO OPERA\fION PRECAU\fIONS
WARNING:
Do not adjust the audio system while driving so
that full attention may be given to vehicle
operation.
\fhe audio s\bstem operates when the ignition switch is
in the “ACC” or “ON” position.
Radio
.Radio reception is affected b\b station signal
strength, distance from radio transmitter, build-
ings, bridges, mountains and other external
influences. Intermittent changes in reception
qualit\b normall\b are caused b\b these external
influences.
. Using a cellular phone in or near the vehicle ma\b
influence radio reception qualit\b.
Compact Disc (CD) pla\ber
.During cold weather or rain\b da\bs, the pla\ber ma\b
malfunction due to the humidit\b. If this occurs,
remove the CD from CD pla\ber and dehumidif\b or
ventilate the pla\ber completel\b.
. \fhe pla\ber ma\b skip while driving on rough roads.
. \fhe CD pla\ber sometimes ma\b not function when
the passenger compartment temperature is ex-
tremel\b high. Lower the temperature before use.
. Do not expose the CD to direct sunlight.
. CDs that are of poor qualit\b, or are dirt\b,
scratched, covered with fingerprints, or that have
pin holes ma\b not work properl\b.
. \fhe following CDs ma\b not work properl\b.
— Cop\b control compact discs (CCCD) — Recordable compact discs (CD-R)
— Rewritable compact discs (CD-RW)
SAA0480
.
Do not use the following CDs as the\b ma\b cause
the CD pla\ber to malfunction.
— 8 cm (3.1 in) discs (except for FM-AM Radio
with Compact Disc Pla\ber (\f\bpe C))
— CDs that are not round
— CDs with a paper label
— CDs that are warped, scratched or have unusual edges.
AUDIO SYSTEM (if equipped)
& R Q G L W L R Q
Page 206 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-20Starting and driving
.when the selector lever is in the "R" (Reverse\f
position.
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the Electric power steering warning light or
the Anti-lock Braking System (ABS\f warning light
(if equippe\b\f illuminate.
. when the brake pe\bal is not \bepresse\b.
. when stopping the vehicle on sloping roa\bs.
. when the power consumption is large.
NOTE:
It may take some time until Idling Stop System
activates under the following conditions:
. when the battery is \bischarge\b.
. when the outsi\be temperature is low.
. when the battery is replace\b or the battery
terminal is \bisconnecte\b for exten\be\b perio\bs
an\b then reconnecte\b.
NOTE:
The engine will not restart with releasing the
brake pedal while Idling Stop System is acti-
vated under the following condition:
. when the selector lever is in the "P" (Park\f
position.
NOTE:
The engine will restart without releasing the
brake pedal while Idling Stop System is acti-
vated under the following conditions:
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the accelerator pe\bal is \bepresse\b. .
when the steering wheel is operate\b.
. when the battery capacity is low.
. when the power consumption is large.
. when the brake pe\bal is release\b on sloping roa\bs
an\b the vehicle is move\b.
. when the brake pe\bal is release\b with the selector
lever in the "D" (Drive\f or "N" (Neutral\f position.
. when the selector lever is place\b in the "L" (Low\f ,
"D" (Drive\f or "R" (Reverse\f position from the "N"
or "P" position.
. When the negative pressure of the brake system is
not sufficiently applie\b by \bepressing the brake
pe\bal several times.
Use this system while waiting at stoplight, etc. When
the vehicle is stoppe\b for long perio\bs of time, turn off
the engine.
When the engine hoo\b is opene\b with I\bling Stop
System on, the engine will be in the normal stoppe\b
state with the buzzer soun\bing. In this case, restart the
engine with the ignition switch.
When the \briver’s \boor is opene\b with I\bling Stop
System on, I\bling Stop System continues to be
activate\b although the buzzer soun\bs an\b the I\bling
Stop System in\bicator light blinks.
OPERATING IDLING STOP SYSTEM
NOTE:
. The engine stops automatically when the
brake pedal is depressed with the selector
lever in the "D" (Drive) position.
. When the brake pedal is released, the
engine restarts automatically.
. When the Idling Stop System is activated,
the Idling Stop System indicator light illu-
minates in the meter. .
The buzzer sounds and the indicator light
appears in the meter, indicating the condi-
tion of the Idling Stop System. For more
details, see “Stop/Start System indicator
light (if equipped for Europe)/Idling Stop
System indicator light (if equipped for Thai-
land)” (P.2-18) or “Idling Stop System remin-
der buzzer (if equipped for Thailand)” (P.2-
19) .
. The accumulated time of Idling Stop System
and the current saved fuel consumption by
Idling Stop System can be checked using the
drive computer, see “Accumulated time and
current saved fuel consumption (ml (mili-
liter)) by Idling Stop System (if equipped for
Thailand)” (P.2-27) .
& R Q G L W L R Q