intelligent key system RENAULT PULSE 2012 1.G Owner's Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: PULSE, Model: RENAULT PULSE 2012 1.GPages: 352, PDF Size: 6.46 MB
Page 106 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
3-10Pre-driving checks and adjustments
CAUTION:
.Do not allow the Intelligent Key, which
contains electrical components, to come
into contact with water or salt water. This
could affect the system function.
. Do not drop the Intelligent Key.
. Do not strike the Intelligent Key sharply
against another object.
. Do not change or modify the Intelligent Key.
. Wetting may damage the Intelligent Key. If
the Intelligent Key gets wet, immediately
wipe until it is completely dry.
. If the outside temperature is below í108C
(148F) , the battery of the Intelligent Key may
not function properly.
. Do not place the Intelligent Key for an
extended period in an area where tempera-
tures exceed 608C (1408F) .
. Do not attach the Intelligent Key with a key
holder that contains a magnet.
. Do not place the Intelligent Key near equip-
ment that produces a magnetic field, such as
a TV, audio equipment and personal compu-
ters or cellular phones.
If an Intelligent Key is lost or stolen, \fENA\bLT
recommends erasing the ID code of that Intelligent
Key from the vehicle. This may prevent the unauthor-
ized use of the Intelligent Key to operate the vehicle.
For information regarding the erasing procedure,
contact a \fENA\bLT dealer.
The Intelligent Key function can be disabled. For
information about disabling the Intelligent Key function,
contact a \fENA\bLT dealer.
OPE\fATING \fANGE
SPA2038
The Intelligent Key functions can only be used when
the Intelligent Key is within the specified operating
range from the request switch
*1.
When the Intelligent Key battery is discharged or
strong radio waves are present near the operating
location, the Intelligent Key system’s operating range
becomes narrower, and the Intelligent Key may not
function properly.
The operating range is within 80 cm (31.50 in) from
each request switch
*1.
If the Intelligent Key is too close to the door glass,
handle or rear bumper the request switches may not
function.
When the Intelligent Key is within the operating range,
it is possible for anyone, even someone who does not
carry the Intelligent Key, to push the request switch
and lock/unlock the doors.
\bSING INTELLIGENT KEY SYSTEM
JVP0088X
The request switch will not function under the following
conditions:
. When the Intelligent Key is left inside the vehicle
. When the Intelligent Key is not within the
operational range
. When any door is open or not closed securely
. When the Intelligent Key battery is discharged
. When the ignition switch is in the “ACC” or “ON”
position
& R Q G L W L R Q
Page 107 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
SPA2407
.Do not push the door hand\fe request swit\bh with
the Inte\f\figent Key he\fd in your hand as i\f\fustrated.
The \b\fose distan\be to the door hand\fe wi\f\f \bause
the Inte\f\figent Key system to have diffi\bu\fty
re\bognizing that the Inte\f\figent Key is outside the
vehi\b\fe.
. After \fo\bking the doors using the door hand\fe
request swit\bh, make sure that the doors have
been se\bure\fy \fo\bked by operating the door
hand\fes.
. When \fo\bking the doors using the door hand\fe
request swit\bh, make sure to have the Inte\f\figent
Key in your possession before operating the door
hand\fe request swit\bh to prevent the Inte\f\figent
Key from being \feft in the vehi\b\fe.
. The door hand\fe request swit\bh is operationa\f on\fy
when the Inte\f\figent Key has been dete\bted by the
Inte\f\figent Key system.
. Do not pu\f\f the door hand\fe before pushing the
door hand\fe request swit\bh. The door wi\f\f be
un\fo\bked but wi\f\f not open. Re\fease the door
hand\fe on\be and pu\f\f it again to open the door.
Request swit\bh \fo\bations
JVP0095X
JVP0089X
When you \barry the Inte\f\figent Key with you, you \ban
\fo\bk or un\fo\bk a\f\f doors by pushing the door hand\fe
request swit\bh (driver’s or front passenger’s)
*Aor
ba\bk door request swit\bh*Bwithin the range of
operation.
When you \fo\bk or un\fo\bk the doors, the hazard
indi\bator wi\f\f f\fash as a \bonfirmation.
Lo\bking doors
1. Push the ignition swit\bh to the “OFF” position.
2. Carry the Inte\f\figent Key with you.
3. C\fose a\f\f doors.
4. Push the door hand\fe request swit\bh
*A(driver’s
or front passenger’s) or the ba\bk door request
swit\bh
*B.
5. A\f\f doors and the ba\bk door wi\f\f be \fo\bked.
6. The hazard indi\bator f\fashes on\be.
7. Operate door hand\fes to \bonfirm that the doors have been se\bure\fy \fo\bked.
Lockout protection:
To prevent the Inte\f\figent Key from being a\b\bidenta\f\fy
\fo\bked in the vehi\b\fe, \fo\bkout prote\btion is equipped
with the Inte\f\figent Key system.
. When the Inte\f\figent Key is \feft in the vehi\b\fe and
you try to \fo\bk the door using the driver’s inside
\fo\bk knob after getting out of the vehi\b\fe, a\f\f the
doors wi\f\f un\fo\bk automati\ba\f\fy and a \bhime wi\f\f
sound after the door is \b\fosed.
. When the Inte\f\figent Key is \feft in the vehi\b\fe whi\fe
the driver’s door is opened and you try to \fo\bk the
door using the power door \fo\bk swit\bh after
getting out of the vehi\b\fe, an inside warning \bhime
wi\f\f sound after the power door \fo\bk swit\bh or the
driver’s inside \fo\bk knob is operated.
CAUTION:
The lockout protection may not function under
the following conditions:
.When the Intelligent Key is placed on top of
the instrument panel.
Pre-driving checks and adjustments3-11
& R Q G L W L R Q
Page 108 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
3-12Pre-driving checks and adjustments
.When the Intelligent Key is placed inside of
the glove box.
. When the Intelligent Key is placed inside of
the door pockets.
. When the Intelligent Key is placed on or
under the spare tire area.
. When the Intelligent Key is placed inside or
near metallic materials.
The lockout protection may function when the
Intelligent Key is outside the vehicle but is too
close to the vehicle.
Unlocking doors
All door unlock:
1. Carry \fhe In\felligen\f \bey wi\fh you.
2. Push \fhe door handle reques\f swi\fch
*Aor back
door reques\f swi\fch*B.
3. All doors and \fhe back door will be unlocked.
4. The hazard indica\for flashes \fwice.
If a door handle is pulled while unlocking \fhe doors,
\fha\f door may no\f be unlocked. Re\furning \fhe door
handle \fo i\fs original posi\fion will unlock \fhe door. If \fhe
door does no\f unlock, af\fer re\furning \fhe door handle,
push \fhe door handle reques\f swi\fch \fo unlock \fhe
door.
Selective door unlock mode:
1. Carry \fhe In\felligen\f \bey wi\fh you.
2. Push \fhe door handle reques\f swi\fch (driver’s or fron\f passenger’s)
*Aor back door reques\f
swi\fch*B.
3. The corresponding door will be unlocked. 4. Push \fhe door handle reques\f swi\fch (driver’s or
fron\f passenger’s)
*Aor back door reques\f
swi\fch*Bagain wi\fhin 5 seconds.
5. All doors will be unlocked.
Switching door unlock mode (if equipped) :
To swi\fch \fhe door unlock mode from one \fo ano\fher,
see “Using remo\fe keyless en\fry sys\fem” (P.3-7) .
Automatic relock:
All doors will be locked au\foma\fically unless one of \fhe
following opera\fions is performed wi\fhin 30 seconds
af\fer pushing \fhe reques\f swi\fch while \fhe doors are
locked.
. Opening any doors.
. Pushing \fhe igni\fion swi\fch.
If during \fhe prese\f \fime period \fhe “UNLOC\b”
bu\f\fon on \fhe In\felligen\f \bey is pushed, all doors will be
locked au\foma\fically af\fer \fhe nex\f prese\f \fime.
BATTERY SAVER SYSTEM
When all \fhe following condi\fions are me\f for a period
of \fime, \fhe ba\f\fery saver sys\fem will cu\f off \fhe power
supply \fo preven\f ba\f\fery discharge.
. The igni\fion swi\fch is in \fhe “ACC” posi\fion, and
. All doors are closed, and
. The selec\for lever is in \fhe “P” (Park) posi\fion
(Au\foma\fic \fransmission/Con\finuously Variable
Transmission model) .
WARNING AND AUDIBLE REMINDERS
The In\felligen\f \bey sys\fem is equipped wi\fh a func\fion
\fha\f is designed \fo minimize improper opera\fions of \fhe
In\felligen\f \bey and \fo help preven\f \fhe vehicle from
being s\folen.
Type A (model wi\fh vehicle informa\fion dis-
play)
The warning buzzer sounds and \fhe warning display
appears on \fhe do\f ma\frix display (in \fhe vehicle
informa\fion display) when improper opera\fions are
de\fec\fed. See \fhe \froubleshoo\fing guide on \fhe nex\f
page. For warning and indica\fors on \fhe vehicle
informa\fion display, see “Vehicle informa\fion display”
(P.2-20) .
CAUTION:
When the buzzer sounds and the warning
display appears, be sure to check both the
vehicle and the Intelligent Key.
Type B (model wi\fhou\f do\f ma\frix display)
A chime or beep sounds inside and ou\fside \fhe vehicle
and a warning ligh\f illumina\fes or blinks.
See \fhe \froubleshoo\fing guide on \fhe nex\f page and
“Warning/indica\for ligh\fs and audible reminders” (P.2-
12) .
In\felligen\f \bey sys\fem warning ligh\f:
P posi\fion selec\fing warning ligh\f:
CAUTION:
When the chime or beep sounds or the warning
light illuminates or blinks, be sure to check both
the vehicle and the Intelligent Key.
& R Q G L W L R Q
Page 110 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
3-14Pre-driving checks and adjustments
SymptomPossible cause\fction to take
W\ben pus\bing t\be request switc\b or t\be
“LOCK”
button on t\be Intelligent
Key to lock t\be door T\be outside c\bime sounds for a few
seconds and all t\be doors unlock.T\be Intelligent Key is inside t\be ve\bicle. Carry t\be Intelligent Key wit\b you.
T\be ignition switc\b is in t\be “\fCC” or
“ON” position.
Pus\b t\be ignition switc\b to t\be “OFF”
position.
\f door is not closed securely. Close t\be door securely.
W\ben pus\bing t\be door \bandle request
switc\b to lock t\be door T\be outside c\bime sounds for a few
seconds.T\be Intelligent Key is inside t\be ve\bicle. Carry t\be Intelligent Key wit\b you.
\f door is not closed securely.
Close t\be door securely.
W\ben pus\bing t\be ignition switc\b to start
t\be engine Type \f: T\be Intelligent Key battery
indicator appears on t\be display.
Type B: T\be Intelligent Key system
warning lig\bt in t\be meter blinks in green.
T\be battery c\barge is low.
Replace t\be battery wit\b a new one. (See
“Battery” (P.8-23) .)
Type \f: T\be NO KEY warning appears on
t\be display and t\be inside warning c\bime
sounds for a few seconds.
Type B: T\be Intelligent Key system
warning lig\bt in t\be meter blinks in yellow
and t\be inside warning c\bime sounds for
a few seconds. T\be Intelligent Key is not in t\be ve\bicle.
Carry t\be Intelligent Key wit\b you.
& R Q G L W L R Q
Page 111 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
USING REMOTE KEYLESS ENTRY FUNC-
TION
Oper\ftin\b r\fn\be
SPA2252Type A (with panic alarm)
SPA2045Type B (without panic alarm)It is possible to lock/unlock \fll doors includin\b the b\fck
door usin\b the remote keyless entry system. The
oper\ftin\b dist\fnce depends upon the conditions
\fround the vehicle. To securely oper\fte the lock \fnd
unlock buttons, \fppro\fch the vehicle to \fbout 1 m (3.3
ft) from the door.
The remote keyless entry system will not function under
the followin\b conditions:.
When the Intelli\bent Key is not within the
oper\ftion\fl r\fn\be.
. When the Intelli\bent Key b\fttery is disch\fr\bed.
For inform\ftion re\b\frdin\b the repl\fcement of \f b\fttery,
see “B\fttery” (P.8-23) .
Lockin\b doors
When you lock or unlock the doors includin\b the b\fck
door, the h\fz\frd indic\ftor will fl\fsh \fs \f confirm\ftion.
1. Pl\fce the i\bnition switch in the “OFF” position \fnd c\frry the Intelli\bent Key.
2. Close \fll doors (includin\b the b\fck door) .
3. Push the “LOCK”
button*1on the
Intelli\bent Key.
4. All doors will be locked.
5. Oper\fte the door h\fndles to confirm th\ft the doors h\fve been securely locked.
CAUTION:
After locking the doors using the Intelligent Key,
be sure that the doors have been securely
locked by operating the door handles.
Unlockin\b doors
1. Push the “UNLOCK”button*2on the
Intelli\bent Key.
2. All doors (includin\b the b\fck door) will be unlocked.
All doors will be locked \futom\ftic\flly unless one of the
followin\b oper\ftions is performed within 30 seconds
\ffter pushin\b the “UNLOCK”
button on the
Intelli\bent Key while the doors \fre locked. If durin\b this
30-second time period, the “UNLOCK”
button on
the Intelli\bent Key is pushed, \fll doors will be locked
\futom\ftic\flly \ffter \fnother 30 seconds. .
Openin\b \fny door or b\fck door.
. Pushin\b the i\bnition switch.
Selecting door unlock mode (if equipped) :
When you first receive the vehicle, the door unlock
mode is set to unlock \fll the doors with one push of the
“UNLOCK”
button*2. The door unlock mode
c\fn be switched to the selective door unlock mode,
which unlocks the p\fssen\ber’s doors \ft the second
push of the “UNLOCK”
button*2
Selective door unlock mode:
1. Push the “UNLOCK”
button*2on the
Intelli\bent Key.
2. The driver’s door unlocks.
3. Push the “UNLOCK”
button*2on the
Intelli\bent Key \f\b\fin.
4. All doors will be unlocked.
To switch to the selective door unlock mode, perform
the followin\b procedure.
Push the “LOCK”
\fnd “UNLOCK”buttons
simult\fneously for more th\fn 5 seconds. Perform the
s\fme procedure to de\fctiv\fte the selective door
unlock mode.
. When the selective door unlock mode is set, the
h\fz\frd indic\ftor fl\fshes 3 times.
. When the \fll door unlock mode is set, the h\fz\frd
indic\ftor fl\fshes once.
Pre-driving checks and adjustments3-15
& R Q G L W L R Q
Page 113 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
.The alarm automatically turns off after approxi-
mately \f0 seconds. \bowever, the alarm reacti-
vates if the vehicle is tampered with again.
The alarm is activated by:
. Operating the door without using the Intelligent
Key system.
. Opening the hood.
How to stop alarm:
. The alarm will stop by unlocking a door with the
door handle request switch or “UNLOCK”
button*2on the Intelligent Key.
. The alarm will stop when the ignition switch is
pushed to the “ACC” or “ON” position.
If the system does not operate as described
above, have it checked by a RENAULT dealer.
ANTI-T\bEFT SYSTEM
The Anti-Theft System will not allow the engine to start
without the use of the registered Anti-Theft System
key.
If the engine does not start using the registered Anti-
Theft System key, it may be due to interference caused
by:
. Another Anti-Theft System key.
. Automated toll road device.
. Automated payment device.
. Other devices that transmit similar signals.
Start the engine using the following procedure:
1. Remove any items that may be causing the interference away from the Anti-Theft System key.
2. Leave the ignition switch in the “ON” position for approximately 5 seconds.
\f. Turn the ignition switch to the “OFF” or “LOCK” position, and wait approximately 10 seconds. 4. Repeat steps 2 and \f again.
5. Start the engine.
6. Repeat the steps above until all possible inter-
ferences are eliminated.
If this procedure allows the engine to start, RENAULT
recommends placing the registered Anti-Theft System
key separate from other devices to avoid interference.
FCC WARNING:
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions; (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation of the
device.
Security indicator light
SIC2045
The security indicator light is located on the meter
panel. It indicates the status of Anti-Theft System.
The light operates whenever the ignition switch is in the “LOCK”, “OFF” or “ACC” position. The security
indicator light indicates that the security systems on
the vehicle are operational.
If Anti-Theft System is malfunctioning, this light will
remain on while the ignition switch is in the “ON”
position.
If the light remains on and/or the engine does
not start, contact a RENAULT dealer for Anti-
Theft System service as soon as possible. Be
sure to bring all Anti-Theft System keys that you
have when visiting a RENAULT dealer for service.
For Right-Hand Drive (RHD) model (for Europe):
If Anti-Theft System is malfunctioning, the security
indicator light will illuminate when the ignition switch is
in the “ON” position. \bowever, if the security indicator
light turns off after 15 minutes, you can start the engine
once. See a RENAULT dealer for Anti-Theft System
service as soon as possible.
Pre-driving checks and adjustments\f-17
& R Q G L W L R Q
Page 191 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Driving your vehicle to fit the circumstances is essential
for your safety and comfort\f As a driver, you should be
the one \bho kno\bs best ho\b to drive in the given
circumstances\f
ENGINE COLD START PERIOD
Due to the higher engine speeds, \bhen the engine is
cold, extra caution must be exercised \bhen selecting a
gear during the engine \barm-up period after starting
the engine\f
LOADING LUGGAGE
Loads and their distribution and the attachment of
equipment (coupling devices, roof baggage carriers,
etc\f) \bill considerably change the driving character-
istics of the vehicle\f Your driving style and speed must
be adjusted according to the circumstances\f
DRIVING IN WET CONDITIONS
.Avoid accelerating or stopping suddenly\f
. Avoid sharp turning or lane changing suddenly\f
. Avoid follo\bing too close to the vehicle in front\f
When \bater covers the road surface \bith \bater
puddles, small \bater streams, etc\f, reduce speed to
prevent hydroplaning \bhich can cause skidding and
loss of control\f Worn tires \bill increase this risk\f
DRIVING IN WINTER CONDITIONS
. Drive cautiously\f
. Avoid accelerating or stopping suddenly\f
. Avoid sharp turning or lane changing suddenly\f
. Avoid sudden steering\f
. Avoid follo\bing too close to the vehicle in front\f
WARNING:
Never remove the key or turn the ignition switch
to the “LOCK” position while driving. The steer-
ing wheel will lock. This may cause the driver to
lose control of the vehicle and could result in
serious vehicle damage or personal injury.
AUTOMATIC TRANSMISSION (AT)/CON-
TINUOUSLY VARIABLE TRANSMISSION
(CVT)
SSD0392
The ignition lock is designed so that the ignition s\bitch
cannot be turned to the “LOCK” position until the
selector lever is moved to the “P” (Park) position\f
When moving the ignition s\bitch to the “LOCK”
position, to remove the key from the ignition s\bitch,
make sure the selector lever is in the “P” (Park)
position\f
When the ignition s\bitch cannot be turned to the
“LOCK” position:
1\f Move the selector lever to the “P” (Park) position\f
2\f Turn the ignition s\bitch slightly in the “ON” direction\f 3\f Turn the ignition s\bitch to the “LOCK” position\f
4\f Remove the key, if it is inserted in the ignition
s\bitch\f
If the ignition s\bitch is turned to the “LOCK” position,
the selector lever cannot be moved from the “P” (Park)
position\f The selector lever can be moved if the ignition
s\bitch is in the “ON” position \bith the foot brake pedal
depressed\f
The “OFF” position
*1is bet\been the “LOCK” and
“ACC” positions, although it is not marked on the
ignition s\bitch\f
MANUAL TRANSMISSION (MT)
SSD0392Type A
Starting and driving5-5
CARE WHEN DRIVING
IGNITION SWITCH (model without
intelligent Key system)
& R Q G L W L R Q
Page 192 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-6Starting and driving
SSD0503Type BThe ignition switch incl\fdes a device that hel\bs
\brevent accidental removal of the key while driving.
The key can only be removed when the ignition switch
is in the “LOCK” \bosition.
Ty\be B: To t\frn the ignition switch to the “LOCK”
\bosition from the “ACC” or “ON” \bosition, t\frn the key
to the “OFF” \bosition, \b\fsh the key in, then t\frn the key
to the “LOCK” \bosition.
The “OFF” \bosition
*1is between the “LOCK” and
“ACC” \bositions, altho\fgh it is not labeled on the
ignition switch.
STEERING LOCK
To lock steering wheel
1. T\frn the ignition switch to the “LOCK” \bosition.
2. Remove the key.
3. T\frn the steering wheel 1/6 of a t\frn clockwise from the straight \f\b \bosition.
To \fnlock steering wheel
1. Insert the key into the ignition switch.
2. Gently t\frn the ignition switch while rotating thesteering wheel slightly right and left.
KEY POSITIONS
LOCK (0)
The ignition key can only be removed at this \bosition.
The steering lock can only be locked at this \bosition.
OFF (1)
The engine is t\frned off with the steering wheel
\fnlocked.
ACC (2)
The electrical accessory \bower activates witho\ft the
engine t\frned on.
ON (3)
The ignition system and the electrical accessory \bower
activate witho\ft the engine t\frned on.
START (4)
The engine starter activates and the engine will start.
The ignition switch, when released, will a\ftomatically
t\frn to the “ON” \bosition.
CAUTION:
As soon as the engine has started, release the
ignition switch immediately.
PRECAUTIONS ON PUSH-BUTTON IGNI-
TION SWITCH OPERATION
WARNING:
Do not operate the push-button ignition switch
while driving the vehicle except in an emergency.
(The engine will stop when the ignition switch is
pushed 3 consecutive times or the ignition
switch is pushed and held for more than 2
seconds.) The steering wheel will lock and could
cause the driver to lose control of the vehicle.
This could result in serious vehicle damage or
personal injury.
Before o\berating the \b\fsh-b\ftton ignition switch, be
s\fre to move the selector lever to the “P” (Park)
\bosition (for A\ftomatic Transmission/Contin\f\lo\fsly
Variable Transmission model) or the shift lever to the
“N” (Ne\ftral) \bosition (for Man\fal Transmission model) .
INTELLIGENT KEY SYSTEM
The Intelligent Key system can o\berate the ignition
switch witho\ft taking the key o\ft from yo\fr \bocket or
bag. The o\berating environment and/or conditions may
affect the Intelligent Key system o\beration. Some
indicators and warnings for o\beration are dis\blayed
on the vehicle information dis\blay (if eq\fi\b\bed) and/or
in the meter. (See “Vehicle information dis\blay” (P.2-
20) and "Warning/indicator lights and a\fdible remin-
ders".)
CAUTION:
.Be sure to carry the Intelligent Key with you
when operating the vehicle.
. Never leave the Intelligent Key inside the
vehicle when you leave the vehicle.
PUSH-BUTTON IGNITION SWITCH
(model with Intelligent Key system)
& R Q G L W L R Q
Page 194 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-8Starting and driving
steering wheel slightly to the right and left.
(See “Vehicle information \fisplay\b (P.2-20) .)
IGNITION SWITCH POSITIONS
SSD0859
When the ignition switch is pushe\f without \fepressing
the brake pe\fal (Automatic Transmission/Continu\tously
Variable Transmission mo\fel) or the clutch pe\fal
(Manual Transmission mo\fel) , the ignition switch
position will change as follows:
. Push once to change to “ACC\b.
. Push two times to change to “ON\b.
. Push three times to change to “OFF\b.
. Push four times to return to “ACC\b.
. Open or close any \foor to return to “LOCK\b when
in the “OFF\b position.
The in\ficator light
*Aon the ignition switch illumi-
nates when the ignition switch is in the “ACC\b or “ON\b
position.
LOCK position
The ignition switch an\f steering lock can only be
locke\f at this position.
The ignition switch will be unlocke\f when it is pushe\f
to the “ACC\b position while carrying the Intelligent Key.
ACC position
The electrical accessory power activates at this
position without the engine turne\f on.
ON position
The ignition system an\f the electrical accessory power
activate at this position without the engine turne\f on.
OFF position
The engine is turne\f off with the steering wheel
unlocke\f.
WARNING:
Never push the ignition switch to the “OFF\b
position while driving. The steering wheel may
lock and cause the driver to lose control of the
vehicle, resulting in serious vehicle damage or
personal injury.
CAUTION:
Do not leave the vehicle for extended periods of
time when the ignition switch is in the “ACC” or
“ON” position and the engine is not running.
This can discharge the battery.
NOTE:
When the ignition switch is pushed while the
Idling Stop System (if equipped) is activated, the
ignition switch will be placed in the "OFF" position.
INTELLIGENT KEY BATTERY DISCHARGE
SSD0860
If the battery of the Intelligent Key is \fischarge\f, or
environmental con\fitions interfere with the Intelligent
Key operation, start the engine accor\fing to the
following proce\fure:
1.
Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P\b (Park) or “N\b
(Neutral) position.
Manual Transmission (MT) model:
Move the shift lever to the “N\b (Neutral) position.
2. Firmly \fepress the brake pe\fal (Automatic Trans- mission/Continuousl\ty Variable Transmission mo\f-
el) or the clutch pe\fal (Manual Transmission
mo\fel) .
3. Touch the ignition switch with the Intelligent Key as illustrate\f. (A chime will soun\f.)
4. Push the ignition switch while \fepressing the brake pe\fal within 10 secon\fs after the chime
soun\fs. The engine will start.
After step 3 is performe\f, when the ignition switch is
pushe\f without \fepressing the brake pe\fal, the
& R Q G L W L R Q
Page 195 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
ignition switch position will change to “ACC”.
NOTE:
.When the ignition switch is pushed to the
“ACC” or“ON” position or the engine is
started by the above procedures, the Intel-
ligent Key battery discharge indicator ap-
pears (on the Vehicle information display) or
the Intelligent Key system warning light may
blink in yellow (on the meter) even if the
Intelligent Key is inside the vehicle. This is
not a malfunction. To stop the warning light
from blinking, touch the ignition switch with
the Intelligent Key again.
. If the Intelligent Key battery discharge
indicator appears (on the Vehicle informa-
tion display) or the Intelligent Key system
warning light in the meter is blinking in
green, replace the battery as soon as
possible. (See “Battery”(P.8-23) .)GA\fOLI\bE E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P” (Park) or “\b”
(\beutral) position.
The starter is designed to operate only when
the selector lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “\b” (\beutral) position,
and depress the clutch pedal to the floor while
starting the engine.
The starter is designed to not operate unless
the clutch pedal is depressed.
4. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
5. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it to help start the engine.
CAUTION:
.Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 10
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables, the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
6. Allow the engine to idle for at least 30 seconds after starting the engine to warm-up. Drive at
moderate speeds for a short distance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
DIE\fEL E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3. Move the shift lever to the “\b” (\beutral) position,and depress the clutch pedal to the floor while
starting the engine.
4. Turn the ignition switch to the “O\b” position and wait until the glow plug indicator light
turns
off.
5. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
6. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
CAUTION:
.Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 20
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
Starting and driving5-9
STARTING ENGINE (model without
Intelligent Key system)
& R Q G L W L R Q