window RENAULT PULSE 2012 1.G Owner's Manual


> (GLW    0RGHO .$2(0B5HQDXOW @
2-38Instruments and controls
3. Pull up and hold the driver\fs window switch toclose the driver\fs window. \bold the switch for
approximately 3 seconds after the window has
been fully closed, and then release it.
4. Check if the power window functions operate properly.
If you open or close the power window continuously, it
may cause the power window not to operate properly.
Perform the above procedure.
If the power window functions do not operate properly
after performing the above procedure, repeat the
steps. See a RENAULT dealer, if necessary, for
checking the power window system.WARNING:
Never allow hands, fingers, or any part of your
body within operating range of the sunshade.
You could be injured.
CAUTION:
. Do not place any heavy objects on the roof
glass or surrounding area.
. Do not hang from the sunshade and/or the
sunshade opening or hang any objects from
it. It may cause damage or deformation to
the sunshade.
. Close the sunshade when you leave the
vehicle for extended periods of time to
prevent the inside of the vehicle from reach-
ing high temperatures.
JVI0020X
To open or close the sunshade, operate the knob*A.
To open the sunshade, slide it toward the rear of the
vehicle
*1. To close, slide the sunshade toward the
front of the vehicle*2. If the battery cable is disconnected, the clock will reset
its time and the correct time will not be indicated.
Readjust the time.
For model with the vehicle information display, see
“Vehicle information display” (P.2-20)
For the clock adjustment in the audio unit (if equipped) .
See “Audio system” (P.4-8) .
ADJUSTING TIME
Meter display model (if equipped)
SIC4406
The digital clock*2in the meter displays the time
when the ignition switch is in the “ON” position.
To display the clock, push the adjusting knob
*1. To
adjust the time, perform the following procedure.
1. Push the clock adjusting knob
*1for 3 seconds
or more to enter time adjust mode.
The hours display will start to flash.
2. Push the clock adjusting knob
*1to adjust the
hour.
To advance the time, hold down the knob
*1.
3. Wait at least 5 seconds for the minute display to flash.
SUNSHADE (if equipped) CLOCK
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4. Push the clock adjusting knob*1to adjust the
\finutes.
To advance the ti\fe, hold do\bn the knob
*1.
Wait at least 5 seconds for the second display “:”
to flash.
5. Push the clock adjusting knob
*1to reset the
second counter.
The selected values \bill be stored if no user input is
detected for 60 seconds, or can be reset by using the
adjusting knob.
SIC4436
The po\ber outlet is for po\bering electrical accessories
such as cellular telephone.
CAUTION:
. The outlet and plug may be hot during or
immediately after use.
. This power outlet is not designed for use
with a cigarette lighter unit.
. Do not use with accessories that exceed a 12
volt, 120W (10A) power draw. Do not use
double adapters or more than one electrical
accessory.
. Use power outlets with the engine running
to avoid discharging the vehicle battery.
. Avoid using power outlets when the air
conditioner, headlights or rear window de-
fogger is on.
. Before inserting or disconnecting a plug, be
sure to turn off the power switch of electrical
accessory being used and the ignition
switch.
. Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may open. .
Do not allow water to contact the outlet.
. When not in use, be sure to close the cap.
Instruments and controls2-39
POWER OUTLETS (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
3-16Pre-driving checks and adjustments
Using panic alarm (if eq\fipped)
If \bo\f are near \bo\fr vehicle and feel threatened, \bo\f
ma\b activate the alarm to call attention as follows:
1. P\fsh the “PANIC”
b\ftton*3on the
Intelligent Ke\b for more than 0.5 second.
2. The theft warning alarm will sta\b on for 25 seconds.
3. The panic alarm stops when:
. It has r\fn for 25 seconds, or
. An\b of the b\fttons on the Intelligent Ke\b are
p\fshed. (Note: Panic b\ftton sho\fld be p\fshed for
more than 0.5 second.)
Hazard indicator operation
When \bo\f lock or \fnlock the doors, the hazard
indicator will flash as a confirmation.
.“LOCK”: The hazard indicator flashes once.
. “UNLOCK”: The hazard indicator flashes twice. Yo\fr vehicle is eq\fipped with either or both of the
following sec\frit\b s\bstems:
.
Theft warning s\bstem
. Anti-Theft S\bstem*
(* immobilizer)
The sec\frit\b condition will be shown b\b the sec\frit\b
indicator light.
THEFT WARNING SYSTEM
The theft warning s\bstem provides vis\fal and a\fdio
alarm signals if parts of the vehicle are dist\frbed.
Sec\frit\b indicator light
SIC2045
The sec\frit\b indicator light is located in the meter
panel.
This light operates whenever the ignition switch is in
the “ACC”, “OFF” or “LOCK” position. This is normal.
How to activate the system:
1. Close all windows and p\fsh the ignition switch to the “OFF” position.
The system can be activated even if the
windows are open. 2. Carr\b the Intelligent Ke\b with \bo\f and get o\ft of
the vehicle.
3. Make s\fre the hood is closed. Close and lock all doors with the door handle req\fest switch, LOCK
b\ftton*1on the Intelligent Ke\b (If the door
is locked \fsing the inside lock knob, the s\bstem
will not be activated) or power door lock switch (If
the door is locked \fsing the power door lock
switch with all the doors closed, the s\bstem will
not be activated. To activate the s\bstem, lock the
door \fsing the power door lock switch with an\b of
the doors open, then close all the doors) .
4. Confirm that the sec\frit\b indicator light comes on. The sec\frit\b indicator light sta\bs on for approxi-
matel\b 30 seconds. The vehicle sec\frit\b s\bstem is
now pre-armed. After approximatel\b 30 seconds
the vehicle sec\frit\b s\bstem a\ftomaticall\b shifts
into the armed phase. The sec\frit\b light begins to
flash once ever\b approximatel\b 3 seconds.
If, d\fring this 30-second pre-arm time period, the
door is \fnlocked with the door handle req\fest
switch, the “UNLOCK”
b\ftton*2on the
Intelligent Ke\b, the power door lock switch, or the
ignition switch is p\fshed to the “ACC” or “ON”
position, the s\bstem will not arm.
Even when the driver and/or passengers are in
the vehicle, the system will activate with all
doors locked and ignition switch in the “LOCK”
position. Push the ignition switch to the “ACC” or
“ON” position to turn the system off.
Theft warning system operation:
The warning s\bstem will give the following alarm:
. The hazard indicator blinks and the horn so\fnds
intermittentl\b for approximatel\b 30 seconds.
SECURITY SYSTEM (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Circle type
SAA3126
Adjust t\fe air flo\b direction of t\fe ventilators by
opening, closing or rotating.
WARNING:
.The heater and air conditioner operate only
when the engine is running.
. Never leave children or adults who would
normally require the support of others alone
in the vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and
injure themselves. On hot, sunny days,
temperatures in a closed vehicle could
quickly become high enough to cause se-
vere or possibly fatal injuries to people or
animals.
. Do not use the recirculation mode for long
periods as it may cause the interior air to
become stale and the windows to fog up.
. Do not adjust the heating and air condition-
ing controls while driving so that full atten-
tion may be given to vehicle operation.
T\fe \feater and air conditioner operate \b\fen t\fe
engine is running. T\fe air blo\ber \bill operate \b\fen t\fe
ignition s\bitc\f is in t\fe “ON” position even if t\fe
engine is turned off.
NOTE:
. Odors from inside and outside the vehicle
can build up in the air conditioner unit. Odor
can enter the passenger compartment
through the vents.
. When parking, set the heater and air condi-
tioner controls to turn off air recirculation to
allow fresh air into the passenger compart-
ment. This should help reduce odors inside
the vehicle. For model with Idling Stop System (if equipped
for Thailand):
W\fen t\fe air conditioner or rear defogger (if equipped)
is turned on, t\fe Idling Stop System \bill not be
activated.
For model with Stop/Start System (if equipped
for Europe):
T\fe Stop/Start System \bill not stop t\fe engine under
t\fe follo\bing conditions:
.
T\fe front defogger mode is on. (automatic air
conditioner)
. T\fe air flo\b control dial is in t\fe front defogger
position. (manual air conditioner)
. T\fe rear \bindo\b defogger mode is on.
W\file t\fe engine is stopped by t\fe Stop/Start System,
taking one of t\fe follo\bing actions \bill automatically
start t\fe engine:
. Turn t\fe front defogger mode on. (automatic air
conditioner)
. Turn t\fe air flo\b control dial to t\fe front defogger
position. (manual air conditioner)
. Turn t\fe rear \bindo\b defogger mode on.
W\fen t\fe engine is stopped by t\fe Stop/Start System,
performance of t\fe \feater and air conditioner may be
reduced to minimize t\fe fuel consumption. For t\fe best
\feating and air conditioning performance, restart t\fe
engine by pus\fing t\fe Stop/Start System OFF s\bitc\f.
(See “Stop/Start System OFF s\bitc\f” (P.5-23) .)
Heater and air conditioner, and audio system4-3
HEATER AND AIR CONDITIONER (if
equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Temperature control:
Turn the temperature control dial to set the desired
temperature. Turn the dial between the middle and the
ri\fht position to select the hot temperature. Turn the
dial between the middle and the left position to select
the cool temperature.
Heater operation
Heating:
This mode is used to direct heated air to the foot
outlets.
1. \bove the air intake lever to the “
” position for
normal heatin\f.
2. Turn the air flow control dial to the “
” position.
3. Turn the fan speed control “
” dial to the
desired position.
4. Turn the temperature control dial to the desired position between the middle and the hot (ri\fht)
position.
Ventilation:
This mode directs outside air to the side and center
ventilators.
1. \bove the air intake lever to the “
” position.
2. Turn the air flow control dial to the “
” position.
3. Turn the fan speed control “
” dial to the
desired position.
4. Turn the temperature control dial to the desired position. Defrosting or defogging:
This mode directs the air to the defo\f\fer outlets to
defrost/defo\f the windows.
1. \bove the air intake lever to the “
” position.
2. Turn the air flow control dial to the “
” position.
3. Turn the fan speed control “
” dial to the
desired position.
4. Turn the temperature control dial to the desired position between the middle and the hot (ri\fht)
position.
5. Turn the side ventilators to the side windows to defrost or defo\f for a clear view to the side
mirrors.
. To remove frost from the outside surface of the
windshield quickly, turn the temperature control
dial to the maximum hot position and the fan
speed control “
” dial to the maximum position.
. If it is difficult to defo\f the windshield, turn the
“A/C” button (if equipped) on.
Bi-level heating:
This mode directs cool air from the side and center
vents and warm air from the foot outlets. When the
temperature control dial is turned to the maximum hot
or cool position, the air between the ventilators and the
foot outlets is the same temperature.
1. \bove the air intake lever to the “
” position.
2. Turn the air flow control dial to the “
” position.
3. Turn the fan speed control “
” dial to the
desired position.
4. Turn the temperature control dial to the desired position. Heating and defogging:
This mode heats the interior and defo\fs the windows.
1. \bove the air intake lever to the “
” position.
2. Turn the air flow control dial to the “
” position.
3. Turn the fan speed control “
” dial to the
desired position.
4. Turn the temperature control dial to the maximum hot (ri\fht) position.
5. Turn the side ventilators to the side windows to defrost or defo\f for a clear view to the side
mirrors.
Air conditioner operation (if equipped)
The air conditioner system should be operated for
approximately 10 minutes at least once a month. This
helps prevent dama\fe to the air conditioner system
due to the lack of lubrication.
Cooling:
This mode is used to cool and dehumidify the air.
1. \bove the air intake lever to the “
” position.
2. Turn the air flow control dial to the “
” position.
3. Turn the fan speed control “
” dial to the
desired position.
4. Push the “A/C” button on. (The “A/C” indicator li\fht will illuminate.)
5. Turn the temperature control dial to the desired position between the middle and the cool (left)
position.
. For quick coolin\f when the outside temperature is
hi\fh, move the air intake lever to the “
”
position. Be sure to move the air intake lever to the
“
” position for normal coolin\f.
Heater and air conditioner, and audio system4-5
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
3. Push the temperature control “”/“” \fut-
ton to set the desired temperature.
. \bo not set the temperature lower than the outside
air temperature. \boing so may cause the tem-
perature to not \fe controlled properly.
. If the windows fog up, use dehumidified heating
instead of the A/C off heating.
Dehumidified defrosting/defogging:
1. Push the front defogger “
” \futton. (The
“” indicator light will illuminate.)
2. Push the temperature control “
”/“” \fut-
ton to set the desired temperature.
. To remove frost from the outside surface of the
windshield quickly, set the temperature to a high
temperature and the fan speed to the maximum
level.
. After the windshield is cleared, push the front
defogger “
” \futton again. (The indicator light
will turn off.)
. When the front defogger “
” \futton is pushed,
the air conditioner will automatically turn on when
the outside air temperature is a\fove í28C (288F)
to defog the windshield. The air recirculation mode
will automatically turn off. The outside air circula-
tion mode “
” will \fe selected to improve the
defogging performance.
Manual operation
The manual mode can \fe used to control the heater
and air conditioner to your desired settings. (“MAN-
UAL” will appear on the display.)
To turn off the heater and air conditioner, push the
“OFF” \futton. Fan speed control:
Push the fan speed control “
”/“” \futton. Push
the “” \futton to increase the fan speed. Push the
“” \futton to decrease the fan speed.
Push the “AUTO” \futton to change the fan speed to
the automatic mode.
Air flow control:
Push the “MO\bE” \futton to change the air flow mode.
— Air flows from the center and side ventila- tors.
— Air flows from the center and side ventila-tors and foot outlets.
— Air flows mainly from the foot outlets
— Air flows from the defogger outlets and footoutlets.
Temperature control:
Push the temperature control “
”/“” \futton to
set the desired temperature. Push the “” \futton to
increase the temperature. Push the “” \futton to
decrease the temperature.
Outside air circulation:
Push the outside air circulation “
” \futton to draw
the air flow from outside the vehicle. (The “”
indicator light will illuminate.)
Air recirculation:
Push the air recirculation “
” \futton to circulate the
air flow inside the vehicle. (The “” indicator light
will illuminate.) Automatic air intake control:
If the indicator light on either the outside air circulation
“
” \futton or the air recirculation “” \futton is
illuminated, push the \futton with the light illuminated to
turn the light off. The automatic control is set \fetween
the outside air circulation “
” and air recirculation
“” modes.
SERVICING AIR CON\bITIONER
WARNING:
The air conditioner system contains refrigerant
under high pressure. To avoid personal injury,
any air conditioner service should be done only
by an experienced technician with the proper
equipment.
The air conditioner system in your vehicle is charged
with a refrigerant designed with the environment in
mind.
This refrigerant will not harm the earth’s ozone
layer. However, it may contri\fute in a small part to
glo\fal warming.
Special charging equipment and lu\fricant are required
when servicing your vehicle’s air conditioner. Using
improper refrigerants or lu\fricants will cause severe
damage to the air conditioner system. (See “Air
conditioner system refrigerant and lu\fricant” (P.9-4) .)
A RENAULT dealer will \fe a\fle to service your
environmentally friendly air conditioner system.
Heater and air conditioner, and audio system4-7
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-8Heater and air conditioner, and audio system
Air conditioner filter (if equipped)
\fhe air conditioner s\bstem is equipped with an air
conditioner filter which collects pollen. \fo make sure
the air conditioner heats defogs, and ventilates
efficientl\b, replace the filter according the specified
maintenance intervals listed in a separate maintenance
booklet. \fo replace the filter, contact a RENAUL\f
dealer.
\fhe filter should be replaced if the air flow decreases
significantl\b or if windows fog up easil\b when operating
the heater or air conditioner.AUDIO OPERA\fION PRECAU\fIONS
WARNING:
Do not adjust the audio system while driving so
that full attention may be given to vehicle
operation.
\fhe audio s\bstem operates when the ignition switch is
in the “ACC” or “ON” position.
Radio
.Radio reception is affected b\b station signal
strength, distance from radio transmitter, build-
ings, bridges, mountains and other external
influences. Intermittent changes in reception
qualit\b normall\b are caused b\b these external
influences.
. Using a cellular phone in or near the vehicle ma\b
influence radio reception qualit\b.
Compact Disc (CD) pla\ber
.During cold weather or rain\b da\bs, the pla\ber ma\b
malfunction due to the humidit\b. If this occurs,
remove the CD from CD pla\ber and dehumidif\b or
ventilate the pla\ber completel\b.
. \fhe pla\ber ma\b skip while driving on rough roads.
. \fhe CD pla\ber sometimes ma\b not function when
the passenger compartment temperature is ex-
tremel\b high. Lower the temperature before use.
. Do not expose the CD to direct sunlight.
. CDs that are of poor qualit\b, or are dirt\b,
scratched, covered with fingerprints, or that have
pin holes ma\b not work properl\b.
. \fhe following CDs ma\b not work properl\b.
— Cop\b control compact discs (CCCD) — Recordable compact discs (CD-R)
— Rewritable compact discs (CD-RW)
SAA0480
.
Do not use the following CDs as the\b ma\b cause
the CD pla\ber to malfunction.
— 8 cm (3.1 in) discs (except for FM-AM Radio
with Compact Disc Pla\ber (\f\bpe C))
— CDs that are not round
— CDs with a paper label
— CDs that are warped, scratched or have unusual edges.
AUDIO SYSTEM (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-10Heater and air conditioner, and audio system
.The in-vehicle antenna for BluetoothŠco\f\fu-
nication is built in the syste\f\b Do not place the
Bluetooth
Šaudio device in an area surrounded by
\fetal, far away fro\f the syste\f or in a narrow
space where the device closely contacts the body
or the seat\b Otherwise, sound degradation or
connection interference \fay occur\b
. While a Bluetooth
Šaudio device is connected
through the BluetoothŠwireless connection, the
battery power of the device \fay discharge quicker
than usual\b
. This syste\f is co\fpatible with the Bluetooth
ŠAV
profile (A2DP and AVRCP) \b
BluetoothŠis a trade\fark owned
by Bluetooth SIG, Inc\b, and li-
censed to Daewoo IS Corp\b
Co\fpact Disc with MP3 or WMA (if
equipped)
Explanation of terms:
. MP3 — MP3 is short for Moving Pictures Experts
Group Audio Layer 3\b MP3 is the \fost well known
co\fpressed digital audio file for\fat\b This for\fat
allows for near “CD quality” sound, but at a
fraction of the size of nor\fal audio files\b MP3
conversion of an audio track fro\f CD can reduce
the file size by approxi\fately 10:1 ratio (Sa\fpling:
44\b1 kHz, Bit rate: 128 kbps) with virtually no
perceptible loss in quality\b MP3 co\fpression
re\foves the redundant and irrelevant parts of a
sound signal that the hu\fan ear doesn’t hear\b
. WMA — Windows Media Audio (WMA) is a
co\fpressed audio for\fat created by Microsoft as
an alternative to MP3\b The WMA codec offers
greater file co\fpression than the MP3 codec,
enabling storage of \fore digital audio tracks in the
sa\fe a\fount of space when co\fpared to MP3s at the sa\fe level of quality\b
. Bit rate — Bit rate denotes the nu\fber of bits per
second used by a digital \fusic files\b The size and
quality of a co\fpressed digital audio file is
deter\fined by the bit rate used when encoding
the file\b
. Sa\fpling frequency — The rate at which the
sa\fples of a signal are converted fro\f analog to
digital (A/D conversion) per second\b
. Multisession — Multisession is one of the \fethods
for writing data to \fedia\b Writing data once to the
\fedia is called a single session, and writing \fore
than once is called a \fultisession\b
. ID3/WMA Tag — The ID3/WMA tag is the part of
the encoded MP3 or WMA file that contains
infor\fation about the digital \fusic file such as
song title, artist, albu\f title, encoding bit rate,
track ti\fe duration, etc\b ID3 tag infor\fation is
displayed on the Albu\f/Artist/Song title line on
the display\b
* WindowsŠand Windows MediaŠare registered
trade\farks and trade\farks in the United States of
A\ferica and other countries of Microsoft Corporation
of the USA\b Playback order:
SAA1025Playback order chartThe \fusic playback order of the CD with MP3 or
WMA is as illustrated\b
.
The na\fes of folders not containing MP3 or WMA
files are not shown in the display\b
. If there is a file in the top level of the disc, “Root
Folder” is displayed\b
. The playback order is the order in which the files
were written by the writing software\b Therefore,
the files \fight not play in the desired order\b
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Specification chart (model with type A, B, C, D, E, F audio unit):Supported media CD, CD-R, CD-RW
Supported file \fy\ftem\f ISO\b660 LEVEL1, ISO\b660 LEVEL2, Romeo, Joliet
ISO\b660 Level 3 (packet writing) i\f not \fupported.
File\f \faved u\fing the Live File Sy\ftem component (on a Window\f Vi\fta-ba\fed computer)
are not \fupported.
Supported ver\fion\f*1 MP3
Ver\fion
MPEG1, MPEG2, MPEG2.5
Sampling frequency 8 kHz - 48 kHz
Bit rate 8 kbp\f - 320 kbp\f, VBR*4
WMA*3 Ver\fion
WMA7, WMA8, WMA\b
Sampling frequency 32 kHz - 48 kHz
Bit rate 32 kbp\f - 1\b2 kbp\f, VBR*4
Tag information (Song title and Arti\ft name) ID3 tag VER1.0, VER1.1, VER2.2, VER2.3, VER2.4 (MP3 only)
WMA tag (WMA only)
Folder level\f Folder level\f: 8, Folder\f: 255 (including route folder) , File\f: 512 (Max. 255 file\f for one
folder)
Di\fplayable character code\f*2 01: ASCII, 02: ISO-885\b-1, 03: UNICODE (UTF-16 BOM Big Endian) , 04: UNICODE
(UTF-16 Non-BOM Big Endian) , 05: UNICODE (UTF-8) , 06: UNICODE (Non-UTF-16
BOM Little Endian)
*1 File\f created with a combination of 48 kHz \fampling frequency and 64 kbp\f bit rate cannot be played.
*2 Available code\f depend on what kind of media, ver\fion\f and information are going to be di\fplayed.
*3 Protected WMA file\f (DRM) cannot be played.
*4 When VBR file\f are played, the playback time may not be di\fplayed correctly. WMA7 and WMA8 are not applied to VBR.
Heater and air conditioner, and audio system4-11
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
During the first 1,600 km (1,000 miles\f , follow these
recommen\bations to obtain maximum engine perfor-
mance an\b ensure the future reliability an\b economy of
your new vehicle. Failure to follow these recommen\ba-
tions may result in shortene\b engine life an\b re\buce\b
engine performance.
.Do not \brive at a constant spee\b, either fast or
slow, for long perio\bs of time.
. Do not run the engine over 4,000 rpm (HR12 or
HR15 engine\f or 2,500 rpm (K9K engine\f .
. Do not accelerate at full throttle in any gear.
. Do not start quickly.
. Do not brake har\b as much as possible.WARNING:
The driving characteristics of your vehicle will
change remarkably by any additional load and
its distribution, as well as by adding optional
equipment (trailer coupling, roof racks, etc.) .
Your driving style and speed must be adjusted
according to the circumstances. Especially when
carrying heavy loads, your speed must be
reduced adequately.
.Make sure the area aroun\b the vehicle is clear.
. Visually inspect tires for their appearance an\b
con\bition. Measure an\b check the tire pressure for
proper inflation.
. Check that all win\bows an\b lights are clean.
. A\bjust the seat an\b hea\b restraint positions.
. A\bjust the insi\be an\b outsi\be rearview mirror
positions.
. Fasten your seat belt an\b ask all passengers to \bo
the same.
. Check that all \boors are close\b.
. Check the operation of the warning lights when
the ignition switch is turne\b to the “ON” position.
. Maintenance items in the “8. Maintenance an\b \bo-
it-yourself” section shoul\b be checke\b perio\bi-
cally.
WARNING:
.Never leave children or adults who would
normally require the support of others alone
in your vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and
injure themselves. On hot, sunny days,
temperatures in a closed vehicle could
quickly become high enough to cause se-
vere or possibly fatal illness to people or
animals.
. Properly secure all luggage to help prevent it
from sliding or shifting. Do not place lug-
gage higher than the seatbacks. In a sudden
stop or collision, unsecured luggage could
cause personal injury.
EXHAUST GAS (carbon monoxi\be\f
WARNING:
.Do not breathe exhaust gas; it contains
colorless and odorless carbon monoxide.
Carbon monoxide is dangerous. It can cause
unconsciousness or death.
. If you suspect that exhaust fumes are
entering the vehicle, drive with all windows
fully open, and have the vehicle inspected
immediately.
. Do not run the engine in closed spaces such
as a garage.
. Do not park the vehicle with the engine
running for an extended period of time.
Starting and driving5-3
BREAK-IN SCHEDULE
BEFORE STARTING ENGINE PRECAUTIONS WHEN STARTING
AND DRIVING
&RQGLWLRQ