ignition RENAULT PULSE 2012 1.G Manual Online
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: PULSE, Model: RENAULT PULSE 2012 1.GPages: 352, PDF Size: 6.46 MB
Page 201 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
The selector lever cannot be moved out of the
“P”(Park) position and into any of the other
positions if the ignition switch is placed in the
“LOCK” ,“OFF” or“ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the selector lever to “D”, “R” or “L”
without depressing the foot brake pedal
causes the vehicle to move slowly when
the engine is running. Make sure the foot
brake pedal is depressed fully and the
vehicle is stopped before shifting the selec-
tor lever.
. MAKE SURE OF THE SELECTOR LEVER
POSITION - Make sure the selector lever is
in the desired position. “D” and “L” are used
to move forward and “R” to back up.
. WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
selector lever into the driving position
immediately after starting the engine.
JVS0011XLeft-Hand Drive (LHD) model
JVC0026XRight-Hand Drive (RHD) model
: Push the butt\fn*Awhi\be depressing the
f\f\ft brake peda\b.
: Push the butt\fn*A.
: Just m\fve the se\bect\fr \bever.
Shifting
WARNING:
. Apply the parking brake if the selector lever
is in any position while the engine is not
running. Failure to do so could cause the
vehicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
. If the selector lever cannot be moved from
the “P”(Park) position while the engine is
running and the foot brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause an
accident injuring yourself and others.
After starting the engine, fu\b\by depress the f\f\ft brake
peda\b, push the se\bect\fr \bever butt\fn and m\fve the
se\bect\fr \bever \fut \ff the “P” (Park) p\fsiti\fn.
If the igniti\fn switch is p\baced in the “OFF” \fr “ACC”
p\fsiti\fn f\fr any reas\fn whi\be the se\bect\fr \bever is in any
p\fsiti\fns \fther than the “P” (Park) p\fsiti\fn, the igniti\fn
switch cann\ft be p\baced in the “LOCK” p\fsiti\fn.
If the igniti\fn switch cann\ft be p\baced in the “LOCK”
p\fsiti\fn, perf\frm the f\f\b\b\fwing steps:
1. App\by the parking brake.
2. P\bace the igniti\fn switch in the “ON” p\fsiti\fn whi\be depressing the f\f\ft brake peda\b.
3. M\fve the se\bect\fr \bever t\f the “P” (Park) p\fsiti\fn.
4. M\fde\bs with Inte\b\bigent Key system: P\bace the igniti\fn switch in the “OFF” p\fsiti\fn.
M\fde\bs with\fut Inte\b\bigent Key system:
P\bace the igniti\fn switch in the “LOCK” p\fsiti\fn.
Starting and driving5-15
& R Q G L W L R Q
Page 202 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-16Starting and driving
P (Park):
Use this position when the vehicle is par\fed or when
starting the engine.Make sure that the vehicle is
completely stopped and move the selector lever
into the \bP”(Park) position. Apply the par\fing
bra\fe. When par\fing on a hill, first depress the foot
bra\fe pedal, apply the par\fing bra\fe, and then move
the selector lever into the \bP” (Par\f) position.
R (Reverse):
Use this position to bac\f up. Ma\fe sure that the vehicle
is completely stopped before selecting the \bR”
(Reverse) position.
N (Neutral):
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the \bN” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
L (Low):
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine bra\fing on steep downhill grades.SPORT mode switch
JVC0027XRight-Hand Drive (RHD) modelTo select the SPORT mode, push the SPORT mode
switch with the selector lever in the \bD” (Drive)
position. The SPORT mode indicator light
in the
meter panel illuminates. To turn off the SPORT mode,
push the SPORT mode switch again. The SPORT
mode indicator light will turn off. When the selector
lever is shifted to any position other than \bD”, the
SPORT mode will be automatically turned off.
“OFF” position:
For normal driving and fuel economy, use the \bOFF”
position.
“ON” position:
For driving up or down long slopes where engine
bra\fing is necessary, or for powerful acceleration, use
the \bON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the \bON”
position. This reduces fuel economy.
Accelerator downshift - in the \bD” position -
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift loc\f release
JVC0028XRight-Hand Drive (RHD) modelIf the battery charge is low or discharged, the selector
lever may not be moved from the \bP” (Par\f) position
even with the bra\fe pedal depressed and the selector
lever button pushed.
To move the selector lever, perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the \bOFF” or \bLOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the \bLOCK” position,
and remove the \fey if it is inserted.
2. Apply the par\fing bra\fe.
3. Depress the shift loc\f release button.
4. Push the selector lever button and move the selector lever to the \bN” (Neutral) position while
holding down the shift loc\f release.
& R Q G L W L R Q
Page 203 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
& R Q G L W L R Q
Page 206 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-20Starting and driving
.when the selector lever is in the "R" (Reverse\f
position.
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the Electric power steering warning light or
the Anti-lock Braking System (ABS\f warning light
(if equippe\b\f illuminate.
. when the brake pe\bal is not \bepresse\b.
. when stopping the vehicle on sloping roa\bs.
. when the power consumption is large.
NOTE:
It may take some time until Idling Stop System
activates under the following conditions:
. when the battery is \bischarge\b.
. when the outsi\be temperature is low.
. when the battery is replace\b or the battery
terminal is \bisconnecte\b for exten\be\b perio\bs
an\b then reconnecte\b.
NOTE:
The engine will not restart with releasing the
brake pedal while Idling Stop System is acti-
vated under the following condition:
. when the selector lever is in the "P" (Park\f
position.
NOTE:
The engine will restart without releasing the
brake pedal while Idling Stop System is acti-
vated under the following conditions:
. when the rear \befogger is turne\b on.
. when the air con\bitioner is turne\b on.
. when the accelerator pe\bal is \bepresse\b. .
when the steering wheel is operate\b.
. when the battery capacity is low.
. when the power consumption is large.
. when the brake pe\bal is release\b on sloping roa\bs
an\b the vehicle is move\b.
. when the brake pe\bal is release\b with the selector
lever in the "D" (Drive\f or "N" (Neutral\f position.
. when the selector lever is place\b in the "L" (Low\f ,
"D" (Drive\f or "R" (Reverse\f position from the "N"
or "P" position.
. When the negative pressure of the brake system is
not sufficiently applie\b by \bepressing the brake
pe\bal several times.
Use this system while waiting at stoplight, etc. When
the vehicle is stoppe\b for long perio\bs of time, turn off
the engine.
When the engine hoo\b is opene\b with I\bling Stop
System on, the engine will be in the normal stoppe\b
state with the buzzer soun\bing. In this case, restart the
engine with the ignition switch.
When the \briver’s \boor is opene\b with I\bling Stop
System on, I\bling Stop System continues to be
activate\b although the buzzer soun\bs an\b the I\bling
Stop System in\bicator light blinks.
OPERATING IDLING STOP SYSTEM
NOTE:
. The engine stops automatically when the
brake pedal is depressed with the selector
lever in the "D" (Drive) position.
. When the brake pedal is released, the
engine restarts automatically.
. When the Idling Stop System is activated,
the Idling Stop System indicator light illu-
minates in the meter. .
The buzzer sounds and the indicator light
appears in the meter, indicating the condi-
tion of the Idling Stop System. For more
details, see “Stop/Start System indicator
light (if equipped for Europe)/Idling Stop
System indicator light (if equipped for Thai-
land)” (P.2-18) or “Idling Stop System remin-
der buzzer (if equipped for Thailand)” (P.2-
19) .
. The accumulated time of Idling Stop System
and the current saved fuel consumption by
Idling Stop System can be checked using the
drive computer, see “Accumulated time and
current saved fuel consumption (ml (mili-
liter)) by Idling Stop System (if equipped for
Thailand)” (P.2-27) .
& R Q G L W L R Q
Page 207 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
& R Q G L W L R Q
Page 208 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-22Starting and driving
.The driver ’s seat belt is unfastened, or
driver’s door is open (for MT model) .
. The hood is open.
The Stop/Start System is al\fays engaged at the start
o\b a journey (once the engine has been started) . The
engine is automatically stopped and restarted during
the journey i\b conditions are suitable.
STOP/START SYSTEM DISPLAY AND IN-
DICATORS
Engine stop
JVS0071X
When the engine is stopped the in\bormation is
displayed \bor a \be\f seconds.
Vehicle information display: 1. Engine stop guidance
Instrument panel: 2. Stop/Start System indicator light
See “Vehicle in\bormation display” (P.2-20) about the
display. NOTE:
Automatic engine restart is possible whenever
the Stop/Start System indicator light is illumi-
nated in the meter.
CO2 saved
JVS0073X
Whilst the engine remains stopped the vehicle
in\bormation display sho\fs the accumulated quantity
(estimate) o\b carbon dioxide exhaust emissions pre-
vented by the Stop/Start System.
Vehicle information display:
1. CO2 saved in\bormation
Instrument panel: 2. Stop/Start System indicator light
. Push and hold the
button to reset the [CO2
Saved] value.
. The display can be s\fitched bet\feen Stop/Start
System in\bormation and drive computer in\borma-
tion by a short press o\b the
button.
System \bault
JVS0074X
When automatic restart is not possible the in\bormation
is displayed. The engine must be started by turning or
pushing the ignition s\fitch.
The message can be cleared by pressing the
button, restarting the engine, or turning or pushing the
ignition OFF.
Key LOCK \farning
JVS0081XType A
& R Q G L W L R Q
Page 209 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
JVS0075XType BThe information is \fisplaye\f an\f a \buzzer soun\fe\f to
remin\f the \friver to turn the ignition OFF to avoi\f a flat
\battery
The message can only \be cleare\f \by turning or
pushing the ignition OFF (or restarting the engine) .
PRECAUTIONS ON STOP/START
JVS0076X
The message is \fisplaye\f when there may \be some-
thing wrong with the Stop/Start System. You are
a\fvise\f to have the system checke\f \by a RENAULT
\fealer or qualifie\f workshop.Vehicle information display:
1. System fault warning
Instrument panel: 2. Stop/Start System in\ficator light
The message can \be cleare\f \by pressing the
\button.
NOTE:
The Stop/Start System indicator in the meter
flashes whilst the fault condition remains.
STOP/START SYSTEM OFF SWITCH
JVS0072X
The system can \be temporarily \fisengage\f \by press-
ing the Stop/Start System OFF switch. Pressing the
\button a secon\f time will re-engage the Stop/Start
System.
. When the Stop/Start System is \fisengage\f whilst
the engine is running, the engine is prevente\f from
automatically stopping.
. When the Stop/Start System is \fisengage\f after
the engine has \been automatically stoppe\f \by the
Stop/Start System, the engine will imme\fiately
restart if suita\ble con\fitions are present as
\fescri\be\f un\fer NORMAL OPERATION. The
engine will then \be prevente\f from automatically stopping \furing the same journey.
. Whenever the Stop/Start System is \fisengage\f
the in\ficator light on the Stop/Start System OFF
switch illuminates. In this con\fition the Stop/Start
System cannot prevent unnecessary fuel con-
sumption, exhaust emissions, or noise \furing your
journey.
NOTE:
The following messages may be displayed for a
few seconds in the vehicle information display
when the Stop/Start System OFF switch is
pressed.
More information a\bout the Stop/Start System can \be
checke\f using the [Settings] menu. (See “Vehicle
information \fisplay” (P.2-20) a\bout the \fisplay.)
Starting and driving5-23
& R Q G L W L R Q
Page 216 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-30Starting and driving
Setting cruising speed
1. Acce\ferate to the desired speed.
\b. Push the SET íswitch and re\fease it.
3. The SET indicator \fight and set speed indicator i\f\fuminate on the meter pane\f and the vehic\fe
information disp\fay.
4. Take your foot off the acce\ferator peda\f.
The vehic\fe wi\f\f maintain the set speed.
Passing another vehicle:
Depress the acce\ferator peda\f to acce\ferate. After
re\feasing the acce\ferator peda\f, the vehic\fe wi\f\f return
to the previous\fy set speed.
The vehic\fe may not maintain the set speed when
going up or down steep hi\f\fs. In such cases, drive
without the cruise contro\f.
Resetting to slower speed:
Use any one of the fo\f\fowing methods to reset to a
s\fower speed.
. Light\fy tap the foot brake peda\f. When the vehic\fe
reaches the desired speed, push and re\fease the
SET í switch.
. Push and ho\fd the SET í switch. When the vehic\fe
reaches the desired speed, re\fease the SET í
switch.
. Quick\fy push and re\fease the SET í switch. This
wi\f\f reduce the vehic\fe speed by about 1 km/h or 1
MPH.
Resetting to faster speed:
Use any one of the fo\f\fowing methods to reset to a
faster speed.
. Depress the acce\ferator peda\f. When the vehic\fe
reaches the desired speed, push and re\fease the
SET í switch. .
Push and ho\fd the RES+ switch. When the
vehic\fe reaches the desired speed, re\fease the
RES+ switch.
. Quick\fy push and re\fease the RES+ switch. This
wi\f\f increase the vehic\fe speed by about 1 km/h or
1 MPH.
Resuming at preset speed:
Push and re\fease the RES+ switch.
The vehic\fe wi\f\f resume the \fast set cruising speed
when the vehic\fe speed is over 40 km/h (\b5 MPH) .
Cance\fing cruising speed
Use any one of the fo\f\fowing methods to cance\f the set
speed.
. Push the CANCEL switch. The SET indicator \fight
wi\f\f turn off.
. Tap the foot brake peda\f. The SET indicator \fight
wi\f\f turn off.
. Push the cruise contro\f MAIN switch. Both the
SET and cruise indicator \fights turn off.
WARNING:
.Do not stop or park the vehicle over
flammable materials such as dry grass,
waste paper or rags. They may ignite and
cause a fire.
. Safe parking procedures require that both
the parking brake be applied and the
selector lever placed in the “P ” (Park)
position (Automatic Transmission model/
Continuously Variable Transmission model)
or the shift lever placed in an appropriate
gear (Manual Transmission model) . Failure
to do so could cause the vehicle to move
unexpectedly or roll away and result in an
accident.
. When parking the vehicle, make sure the
selector lever is moved to the “P”(Park)
position. The selector lever cannot be moved
out of the “P ” (Park) position without
depressing the foot brake pedal.
. Never leave the engine running while the
vehicle is unattended.
. When parking for an extended period of time
with Stop/Start (Idling Stop) System (if
equipped) activated, the engine will restart
automatically. Never leave the vehicle with
the ignition switch in the “ON”position.
. Never leave children or adults who would
normally require the support of others alone
in the vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and
injure themselves. On hot, sunny days,
temperatures in a closed vehicle could
PARKING
& R Q G L W L R Q
Page 217 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
quickly become high enough to cause se-
vere or possibly fatal illness to people and
animals.
SSD0488
Left-Hand Drive (LHD) model
SSD0489
Right-Hand Drive (RHD) model1. Firmly apply the par\fing bra\fe.
\b. Automatic Transmission (AT)/Continuously Vari-able Transmission (CVT) model: Move the selector
lever to the “P” (Par\f) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position. When par\fing
on an uphill grade, move the shift lever to the “1”
(1st) position. 3. To help prevent the vehicle from moving into traffic
when par\fed on an incline, it is a good practice to
turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
*1
Turn the wheels into the curb and move the vehicle
forward until the curb side wheel gently touches
the curb. Then apply the par\fing bra\fe. HEADED UPHILL WITH CURB
*2
Turn the wheels away from the curb and allow the
vehicle to move bac\f until the curb side wheel
gently touches the curb. Then apply the par\fing
bra\fe.
HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
*3
Turn the wheels toward the side of the road so the
vehicle will move away from the center of the road
if the vehicle moves. Then apply the par\fing bra\fe.
4. Model with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position
and remove the \fey.
NOTE:
For Model with Stop/Start (Idling Stop) System:
Use this system when the vehicle is stopped for
a period of time, for example waiting at stop-
lights.
Stop the engine with the ignition switch when
parking, etc. for an extended period of time.
Starting and driving5-31
& R Q G L W L R Q
Page 218 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
5-32Starting and driving
SSD0723
WARNING:
.The sonar (parking sensor) system is a
convenience but it is not a substitute for
proper parking. Always look around and
check that it is safe to do so before parking.
Always move slowly.
. Read and understand the limitations of the
sonar (parking sensor) system as contained
in this section. Inclement weather may affect
the function of the sonar (parking sensor)
system; this may include reduced perfor-
mance or a false activation.
. This system is not designed to prevent
contact with small or moving objects.
. The system is designed as an aid to the
driver in detecting large stationary objects to
help avoid damaging the vehicle. The system
will not detect small objects below the
bumper, and may not detect objects close
to the bumper or on the ground.
. If your vehicle sustains damage to the
bumper fascia, leaving it misaligned or bent,
the sensing zone may be altered causing inaccurate measurement of obstacles or
false alarms.
CAUTION:
Keep the interior of the vehicle as quiet as
possible to hear the tone clearly.
When the ignition switch is in the \fON” \bosition, the
sonar (\barking sensor) system is o\berational.
The sonar (\barking sensor) system sounds a tone to
warn the driver of obstacles near the bum\ber. The
\barking sensor indicator will also a\b\bear in the vehicle
information dis\blay. (See \fParking Sensor Indicator”
(P.5-32) .) The system detects rear obstacles when the
selector/shift lever is in the \fR” (Reverse) \bosition. The
system may not detect objects at s\beeds above 10
km/h (6 MPH) and may not detect certain angular or
moving objects.
The sonar (\barking sensor) system detects obstacles
u\b to 1 m (3.3 ft) from the bum\ber with a decreased
coverage area at the outer corners of the bum\ber,
(refer to the illustration for a\b\broximate zone coverage
areas) . As you move closer to the obstacle, the rate of
the tone increases. When the obstacle is less than 30cm (11.8 in) away, the tone will sound continuously.
Kee\b the sonar sensors (located on the bum\ber fascia)
free from snow, ice and large accumulations of dirt (do
not clean the sensors with shar\b objects) . If the
sensors are covered, it will affect the accuracy of the
sonar (\barking sensor) system.
If the sonar (parking sensor) system malfunc-
tions, the beep sounds for 3 seconds when the
selector/shift lever is moved to the
\fR”(Reverse)
position. Have the system checked by a RE-
NAULT dealer.
PARKING SENSOR INDICATOR (if
equi\b\bed)
JVS0026X
*1Parking sensor dis\blay
*ACorner sensor indicator
*BCenter sensor indicator
With the sonar (\barking sensor) system ON in the \fR”
(Reverse) \bosition, when the corner/center sensors
(sonar) detect obstacles near the bum\ber, a tone will
sound and the \barking sensor indicator will a\b\bear in
the vehicle information dis\blay
*1.
The \barking sensor indicators
*Aand*Bindicate
the \bosition of the object and the distance to the
SONAR (parking sensor) SYSTEM (if
equipped)
& R Q G L W L R Q