wiring RENAULT SCENIC 2006 J84 / 2.G Power Assisted Steering Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2006, Model line: SCENIC, Model: RENAULT SCENIC 2006 J84 / 2.GPages: 56, PDF Size: 0.18 MB
Page 2 of 56
POWER ASSISTED STEERING
Fault finding - Introduction
36B
36B - 2V6 MR-366-X84-36B000$066_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12136BPOWER ASSISTED STEERING
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type:
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools:
–CLIP + multiplex line sensor
Special tooling required:
3. RECAP
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–vehicle card in reader,
–press and hold the Start button (longer than 5 seconds) with the starting conditions not fulfilled,
–connect the diagnostic tool and perform the required operations. Vehicle(s): Mégane II, Scénic IIComputer name: PAS Computer
Program No.: from 8341
Vdiag No.: 04, 06, 08, 0C and 12
Special tooling required
Multimeter
Elé. 1681 Universal bornier
Note (for Mégane II only):
The left-hand and right-hand xenon bulb computers are powered when the dipped headlights are lit. Fault finding
can only be run on them after the ignition has been switched on in fault finding mode (forced + after ignition feed)
and the dipped headlights are on.
DAETRW_V04_PRELI/DAETRW_V08_PRELI/DAETRW_V06_PRELI/DAETRW_V0C_PRELI/
DAETRW_V12_PRELI
MR-366-X84-36B000$066_eng.mif
Page 5 of 56
POWER ASSISTED STEERING
Fault finding - Introduction
36B
36B - 5V6 MR-366-X84-36B000$066_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
4. FAULT FINDING PROCEDURE (continued)
Wiring check:
Fault finding problems:
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection:
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulation and wiring routing.
Look for signs of oxidation.
Tactile inspection:
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component:
Disconnect the connectors and check the appearance of the clips and tabs, as well as their crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Make sure no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check:
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.
Page 15 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 15V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12POWER ASSISTED STEERING
Fault finding - Interpretation of faults
DF002
PRESENT
OR
STOREDCOMPUTER
DEF : Computer fault
WARNING
Consult the fault contexts.
If PR143 Internal fault codes = 46 and the battery voltage when the fault occurs (PR108) is above 9 V, do not
clear the fault; contact the Techline.
If PR143 Internal fault code = 46 and the battery voltage when the fault occurs (PR108) is less than or equal to
9 V, run fault finding on the battery and charge circuit and clear the fault.
For other values of PR143, do not clear the fault, contact the Techline.
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting or a steering wheel movement from full lock
to full lock.
–Check the condition and connection of the battery terminals.
–Check that the EPAS black 2-track connector is correctly locked.
–Check that the EPAS black 8-track connector is correctly locked.
–Check the condition and conformity of the EPAS fuses: on the power fuse board (70A) and on the UPC (5A).
–Check the conformity of PR108 Computer feed voltage: 12 V < PR108 < 16 V.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF002/DAETRW_V08_DF002/DAETRW_V06_DF002/DAETRW_V0C_DF002/
DAETRW_V12_DF002
MR-366-X84-36B000$462_eng.mif
Page 16 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 16V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF020
PRESENT
OR
STOREDCOMPUTER SUPPLY VOLTAGE
DEF : Computer internal voltage
NOTESSpecial notes:
Although stored in the computer, this fault is not caused by an electric power-assisted
steering failure, but by a poor electrical supply.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine is started or a steering wheel movement
from full lock to full lock.
–Check the condition and connection of the battery terminals.
–Check that the EPAS black 2-track connector is correctly locked.
–Check that the EPAS black 8-track connector is correctly locked.
–Check the condition and conformity of the EPAS fuses: on the power fuse board (70A) and on the UPC (5A).
–Check the conformity of PR108 Computer feed voltage: 12 V < PR108 < 16 V.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Check the voltage of the battery and the charge circuit.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF020/DAETRW_V08_DF020/DAETRW_V06_DF020/DAETRW_V0C_DF020/
DAETRW_V12_DF020
Page 17 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 17V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF033
PRESENT
OR
STOREDMULTIPLEX NETWORK
DEF : CAN connection fault
NOTESSpecial notes:
Although stored in the computer, this fault is not caused by an electric power-assisted
steering failure, but by a multiplex network fault.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine is started or a steering wheel movement
from full lock to full lock.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Check the continuity of the wiring harness for the multiplex network (see 88B, Multiplexing):
Black 8-track connector track 5CAN_L
Black 8-track connector track 7CAN_H
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Multiplex network: repair),
repair the multiplex connection, otherwise change the multiplex connection.
Check the continuity of the wiring harness for the multiplex network (see 88B, Multiplexing)
Black 8-track connector track 4CAN_L instrument panel
Black 8 track connector track 6CAN_H instrument panel
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Multiplex network: repair),
repair the multiplex connection, otherwise change the multiplex connection.
Carry out a multiplex network test and deal with any faults.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF033/DAETRW_V08_DF033/DAETRW_V06_DF033/DAETRW_V0C_DF033/
DAETRW_V12_DF033
Page 18 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 18V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF035
PRESENT
OR
STOREDVARIABLE POWER ASSISTED STEERING MOTOR
DEF : Internal electronic fault
WARNING
For TRW EPAS Vdiag 04 only, consult the fault contexts.
–If PR143 Internal fault code = 58 and if the battery voltage when the fault occurs (PR108) is above 9 V, do not
clear the fault; contact the Techline.
–If PR143 Internal fault code = 58 and if the battery voltage when the fault occurs (PR108) is less than or equal
to 9 V, run fault finding on the battery and charge circuit.
–For other values of PR143, do not clear the fault, contact the Techline.
For the other Vdiag of TRW EPAS, do not clear the fault, contact the Techline.
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting or a steering wheel movement from full lock
to full lock.
Special notes:
Apply the fault finding procedure only on Vdiag 04.
For Vdiag 06, 08, 0C and 12, do not clear the fault and contact the Techline.
–Check the condition and connection of the battery terminals.
–Check that the EPAS black 2-track connector is correctly locked.
–Check that the EPAS black 8-track connector is correctly locked.
–Check the condition and conformity of the EPAS fuses: on the power fuse board (70A) and on the UPC (5A).
–Check the conformity of PR108 Computer feed voltage: 12 V < PR108 < 16 V.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF035/DAETRW_V08_DF035/DAETRW_V06_DF035/DAETRW_V0C_DF035/
DAETRW_V12_DF035
Page 19 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 19V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF038
PRESENT
OR
STOREDANGLE SENSOR
DEF : Sensor internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a steering wheel movement from full lock to full lock
or a road test.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Program the steering wheel angle sensor using command VP004 Steering wheel angle sensor programming.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF038/DAETRW_V08_DF038/DAETRW_V06_DF038/DAETRW_V0C_DF038/
DAETRW_V12_DF038
Page 22 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 22V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF055
PRESENT
OR
STOREDCOMPUTER MEMORY
DEF : EEPROM irregularity
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the battery is disconnected.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Configure the computer using command SC001 Computer calibration, in line with the equipment and vehicle
type.
If the fault is still present, without customer complaints, the EPAS is secure.
If the fault is still present and the assistance level is severely reduced, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF055/DAETRW_V08_DF055/DAETRW_V06_DF055/DAETRW_V0C_DF055/
DAETRW_V12_DF055
Page 23 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 23V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF057
PRESENT
OR
STOREDMULTIPLEX VEHICLE SPEED SIGNAL
DEF : CAN connection fault
NOTESSpecial notes:
Although stored in the computer, this fault is not caused by an electric power-assisted
steering failure, but by a multiplex network fault.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Check the continuity of the wiring harness for the multiplex network (see 88B, Multiplexing):
Black 8-track connector track 5CAN_L
Black 8-track connector track 7CAN_H
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Multiplex network: repair),
repair the multiplex connection, otherwise change the multiplex connection.
Run a multiplex network test and make sure there are no faults.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF057/DAETRW_V08_DF057/DAETRW_V06_DF057/DAETRW_V0C_DF057/
DAETRW_V12_DF057
Page 24 of 56
POWER ASSISTED STEERING
Fault finding - Interpretation of faults
36B
36B - 24V6 MR-366-X84-36B000$462_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
DF059
PRESENT
OR
STOREDANGLE SENSOR
DEF : Sensor internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a steering wheel movement from full lock to full lock
or a road test.
Check that:
–there is a + 12 V before ignition feed on track 1 of the electric power steering black 2-track connector,
–there is an earth on track 2 of the electric power steering black 2-track connector,
–there is a + 12 V after ignition feed on track 8 of the steering column assembly black 8-track connector.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise change the wiring.
Program the steering wheel angle sensor using command VP004 Steering wheel angle sensor programming.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete test with the diagnostic tool.
DAETRW_V04_DF059/DAETRW_V08_DF059/DAETRW_V06_DF059/DAETRW_V0C_DF059/
DAETRW_V12_DF059