service RENAULT SCENIC 2006 J84 / 2.G Tyre Pressure Monitoring Workshop Manual

Chassis
JM0B - JM0C - JM0F - JM0G - JM0H - JM0J - JM0U
77 11 322 262
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the manufacturer
in the production of the various component units and accessories from which his
vehicles are constructed."
FEBRUARY 2006
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2006
TYRE PRESSURE MONITOR
Program No.: 350 and higher
Vdiag: 48 - 4C - 4D - 4F - 50
EDITION 4
Abbreviations 35B-1
Introduction 35B-2
Fault finding log 35B-7
System operation 35B-9
Replacement of components 35B-13
Configuration and programming 35B-14
Conformity check 35B-18
Interpretation of statuses 35B-23
Interpretation of parameters 35B-27
Customer complaints 35B-29
Fault finding chart 35B-30
35B

TYRE PRESSURE MONITOR
Fault finding - System operation
35B
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
System operation:
–The valves are activated after driving at a speed greater than 12 mph (20 km/h).
–During driving, the valves emit signals every minute.
–The valves remain active for 15 minutes after the vehicle stops, then switch to standby mode.
–In standby mode, the valves emit signals only if they detect a pressure difference between two successive
measurements greater than 68 mbar or if the pressure difference since last emitting is greater than 68 mbar (due
to tyre cooling).
–The tyres are considered to be cold when the vehicle speed has been zero for 1h 45 min.
–The minimum time for detection of a leak is approximately 15 minutes.
–The message Pressure unsuitable for the speed is activated only if the vehicle travels at more than 102 mph
(170 km/h) (as an indication) for 3 minutes and the pressure on at least one of the tyres is 400 mbar less than the
recommended pressure at low speed. This message is inactive if the tyres are inflated to motorway pressure,
irrespective of the vehicle speed.
–Alert thresholds:
–over-inflated while cold =recommended pressure + 700 mbar
–over-inflated while warm = recommended pressure + 850 mbar
–under-inflated = recommended pressure - 400 mbar
–very under-inflated = recommended pressure - 600 mbar
–imbalance = difference in pressure between the left-hand and right-hand wheels on the same axle greater
than 500 mbar
–Tyre pressure monitor information messages for the driver:
–"PUNCTURE: CHANGE TYRE" + STOP warning light + highlighting of the wheel concerned on the
instrument panel display + buzzer.
–"ADJUST TYRE PRESSURE" + highlighting of the wheel concerned on the instrument panel.
–"INFLATE TYRES MOTORWAY" + highlighting of all four wheels on the instrument panel.
–"TYRE SENSOR INOPERATIVE" + clearing of the wheel concerned.
–"ELECTRONIC FAULT" + "Service" warning light + the wheels concerned disappear from the
instrument panel.
–Tyre pressure monitor information messages for a puncture with the PAX System:
–"PUNCTURE: REPAIR TYRE" + highlighting of the wheel concerned on the instrument panel.
–"PUNCTURE: SLOW DOWN" + buzzer (if vehicle speed > 48 mph (80 km/h)).
–"DRIVING WITH FLAT: X MILES REMAINING" (X decreases from 120 miles (200 km) to 0) + STOP
warning light when X = 0 + highlighting of the wheel concerned on the instrument panel.
⇒
No instrument panel display of tyre pressure on the SCENIC II.
Edition 435B-10

TYRE PRESSURE MONITOR
Fault finding - Configurations and programming
35B
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
CF023:
TYRE PRESSURE MONITOR FUNCTION
(in programming command SC008 UCH type)
WRITING THE CONFIGURATION WITH OR WITHOUT TYRE PRESSURE MONITOR:
–Select the repair mode menu.
–Select the Programming menu
Select line SC008 UCH type, then the line CF023 Tyre Pressure Monitor function then with or without
Confirm the selection.
Check that the configuration has been stored correctly.
IMPORTANT
CONFIGURATION INCONSISTENCY BETWEEN THE INSTRUMENT PANEL AND UCH
1
st case: If the instrument panel detects the tyre pressure monitor system programmed in the UCH but
not in its own configuration. The message ELECTRONIC FAULT appears, the four wheels
disappear on the instrument panel display, and the Service warning light comes on.
2
nd case: The instrument panel detects that the Tyre pressure monitor is programmed in its own
configuration but the UCH fails to respond to any requests from the instrument panel (not
configured in UCH). The message TYRE SENSOR INOPERATIVE will appear, the four wheels
will disappear from the instrument panel display and the Service warning light will come on.
Edition 435B-16

TYRE PRESSURE MONITOR
Fault finding - Conformity check
35B
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine switched off, after ignition feed on, tyres inflated to correct
pressure.
Order Sub-functionParameter or Status
checked or Action Display and notes Fault finding
3Tyre displayET038:Request lighting of
Service warning
light (only for PAX
System)INACTIVEACTIVE, if a puncture is
detected.
If the pressure of all tyres
is correct, perform fault
finding on the other
computers.
ET039: STOP warning light
requestINACTIVEACTIVE, if a puncture is
detected (without PAX
System) or at the end of
the driving range following
a puncture (with PAX
System).
ET016:Buzzer activation
requestINACTIVE, if the
Tyre Pressure
Monitor system
functions normally
and tyre pressure is
correct.There is a buzzer
activation request for all
severity level 1 warnings
(puncture). The buzzer
emits a single beep when
a fault occurs.
STATUS 1:
Request for buzzer
activation when a
puncture is detected.
STATUS 2
Request for buzzer
activation to warn the
driver that the vehicle
speed is too high when the
vehicle has one or more
punctured tyres. This
information is only valid on
vehicles fitted with PAX
System tyres.
Edition 435B-22