display RENAULT SCENIC 2008 J84 / 2.G Automatic Transmission Siemens TA2000 Owner's Guide

AUTOMATIC TRANSMISSION
Fault finding – Interpretation of statuses23A
23A-92V4 MR-372-J84-23A050$594.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET097
MANUAL MODE
NOTESThere must be no present or stored faults.
This status indicates the gear lever position.
This status displays ACTIVE when the gear lever is in position M, M+ or M-.
This status displays INACTIVE when the gear lever is in positions P, R, N or D.
If the correct status is not displayed, use the interpretation of fault DF093 Manual sequential controls circuits.
If the fault is still present, replace the sequential lever module.
If the fault is still present, contact your Techline.
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2000_V10_ET097/DP0TA2000_V11_ET097/DP0TA2000_V15_ET097

AUTOMATIC TRANSMISSION
Fault finding – Interpretation of statuses23A
23A-93V4 MR-372-J84-23A050$594.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET123
ET124
ET125
MULTIFUNCTION SWITCH S2
MULTIFUNCTION SWITCH S3
MULTIFUNCTION SWITCH S4
NOTESThere must be no present or stored faults.
Multifunction switch contact S1 is not connected on this model.
These statuses show the position of the multifunction switch for each gear lever position.
The switch status can be OPEN or CLOSED (see table below).
S2 S3 S4
POPEN CLOSED CLOSED
ROPEN OPEN OPEN
NCLOSED OPEN CLOSED
DCLOSED CLOSED OPEN
MCLOSED CLOSED OPEN
M+ CLOSED CLOSED OPEN
M- CLOSED CLOSED OPEN
If the correct status is not displayed, use the interpretation of fault DF009 Multifunction switch in prohibited
position.
If after these checks, statuses ET123, ET124 or ET125 are incorrect, replace the multifunction switch.
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2000_V10_ET123/DP0TA2000_V11_ET123/DP0TA2000_V15_ET123/
DP0TA2000_V10_ET124/DP0TA2000_V11_ET124/DP0TA2000_V15_ET124/
DP0TA2000_V10_ET125/DP0TA2000_V11_ET125/DP0TA2000_V15_ET125

AUTOMATIC TRANSMISSION
Fault finding – Interpretation of statuses23A
23A-95V4 MR-372-J84-23A050$594.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET127
LOWER SEQUENTIAL LEVER SWITCH
NOTESThere must be no present or stored faults.
This indicates the status of the lower sequential lever switch.
This status displays ACTIVE with the gear lever in position M-.
This status displays INACTIVE with the gear lever in a position other than M-.
Check the sequential lever supply on the following connections:
●Check for + 12 V on connection AP43 of component 129.
●Check for the vehicle earth on connection N of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the gear lever in position M, measure the voltage of the following connections:
●Check for the vehicle earth on connection 5H of component 129.
●Check for the vehicle earth on connection 5FM of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If any of the measured values is + 12 V, replace the sequential lever
If the values are 0 V, check that the selector lever positions match those displayed on the instrument panel.
Repair if necessary.
If the correct status is not displayed, use the interpretation of fault DF093 Manual sequential controls circuits.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2000_V10_ET128

AUTOMATIC TRANSMISSION
Fault finding – Interpretation of statuses23A
23A-96V4 MR-372-J84-23A050$594.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET128
UPPER SEQUENTIAL LEVER SWITCH
NOTESThere must be no present or stored faults.
This indicates the status of the lower sequential lever switch.
This status displays ACTIVE with the gear lever in position M+.
This status displays INACTIVE with the gear lever in a position other than M+.
Check the sequential lever supply on the following connections:
●Check for + 12 V on connection AP43 of component 129.
●Check for the vehicle earth on connection N of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the gear lever in position M, measure the voltage of the following connections:
●Check for the vehicle earth on connection 5H of component 129.
●Check for the vehicle earth on connection 5FM of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If any of the measured values is + 12 V, replace the sequential lever
If the values are 0 V, check that the selector lever positions match those displayed on the instrument panel.
If the correct status is not displayed, use the interpretation of fault DF093 Manual sequential controls circuits.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2000_V10_ET128/DP0TA2000_V11_ET128/DP0TA2000_V15_ET128

AUTOMATIC TRANSMISSION
Fault finding – Parameter summary table23A
23A - 99V4 MR-372-J84-23A050$660.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ET157
GEAR LEVER UNLOCKING
NOTESThere must be no present or stored faults.
This status indicates whether or not the gear lever is unlocked.
Lever in position P.
The status is YES when the brake pedal is pressed.
The status is NO when the brake pedal is not pressed.
Lever in any position except P.
The status is YES whether or not the brake pedal is pressed.
Check that the instrument panel indicates that the lever is in position P.
Check that, when the brake pedal is pressed, the "Press brake pedal" message disappears from the instrument
panel.
Check the gear lever operation up to the multifunction switch.
Adjust the cable if necessary.
Check that statuses ET154, ET123, ET124 and ET125 Multifunction switch are correct.
If the correct status is not displayed, use the interpretation of fault DF095 Gear lever locking electromagnet
circuit.
If the fault is still present, contact the Techline.
DP0TA2000_V10_ET157/DP0TA2000_V11_ET157/DP0TA2000_V15_ET157

AUTOMATIC TRANSMISSION
23A
23A-115V4 MR-372-J84-23A050$924.mif
SIEMENS TA2000
Vdiag No.: 10-11-15AUTOMATIC TRANSMISSION
Fault finding – Fault Finding Chart
ALP1 No dialogue with the computer
NOTESNone.
Try the diagnostic tool on another vehicle.
Check:
–the connection between the diagnostic tool and the diagnostic socket (connection and cable in good condition),
–the power supply to the computer,
–the engine and passenger compartment fuses.
Check that the CLIP sensor is supplied by connections BP32, MAN and NAM of component 225, displayed when
both red indicator lights on the sensor illuminate.
Make sure that the CLIP sensor is connected to the computer's USB port.
Make sure the CLIP sensor is communicating properly with the vehicle's computers; this can be seen by the two
green diodes on the sensor lighting up.
Check the following connections on component 225:
●Connection code AP43 (+ after ignition feed).
●Connection code BP32 (+ battery).
●Connection code MAN (earth).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
No communication on line K
Check the continuity, insulation and absence of interference resistance on line K of the diagnostic socket.
Disconnect the automatic transmission computer connector to check the insulation, continuity and the absence
of interference resistance of the following connections:
●Connection code AP4 between components 119 and 1337.
●Connection code BP42 between components 119 and 1337.
●Connection code N between components 119 and 107.
●Connection code 3HK between components 119 and 225.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2000_V10_ALP1/DP0TA2000_V11_ALP1/DP0TA2000_V15_ALP1
MR-372-J84-23A050$924.mif

AUTOMATIC TRANSMISSION
Fault finding – Fault Finding Chart23A
23A-117V4 MR-372-J84-23A050$924.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
Start with the ALP1 cycle
ALP3 Automatic transmission operating faults
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
If the engine races when shifting from 1/2 when cold (automatic transmission oil
temperature lower than 15˚C), replace the pressure modulating solenoid valve
(EVM).
Use the diagnostic tool to check the
consistency between the display and the gear
lever positions (ignition on and engine
stopped).Adjust the control settings following the instructions
provided (see MR 370, Mechanical, 23 A,
Automatic Transmission, Automatic
transmission control unit (for Mégane II and
Scénic II)).
Are they consistent?
Check the oil level and the condition of the oil
(colour, odour, etc.).Replace the automatic transmission (see MR 364,
Mechanical, 23A, Automatic transmission,
Removal-Refitting (for Mégane II) and MR 370,
Mechanical, 23A, Automatic transmission,
Removal-Refitting (for Scénic II)). Does the condition of the oil suggest there
is an internal fault in the automatic
transmission?
With the engine stopped, check the line
pressure information provided by the pressure
sensor (PR003 Oil pressure).Replace the pressure sensor (see MR 364,
Mechanical, 23A, Automatic transmission,
Pressure sensor (for Mégane II) and MR 370,
Mechanical, 23A, Automatic transmission,
Pressure sensor (for Scénic II)). Is the value higher than 0.2 bar?
NO
YES
YES
NO
YES
NO
A
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2000_V10_ALP3/DP0TA2000_V11_ALP3/DP0TA2000_V15_ALP3

AUTOMATIC TRANSMISSION
Fault finding – Fault Finding Chart23A
23A-119V4 MR-372-J84-23A050$924.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ALP3
CONTINUED 2
Refer to the procedure and the safety instructions for carrying out a setting point check on the torque converter.
Theoretical engine speed at setting point: 2300 ± 150 rpm
Is the value of the setting point wrong or is there an internal noise in the converter?
Carry out a road test, observing the engine
speed on the instrument panel and the
information displayed on the diagnostic tool
(PR006 Engine speed)Replace the torque converter, the lock-up solenoid
valve and the oil. If the oil is burnt, also replace the
hydraulic distributor and all the solenoid valves
(see MR 364 Mechanical, 23A, Automatic
transmission, Hydraulic distributor
(for Mégane II) and MR 370 Mechanical, 23A,
Automatic transmission, Hydraulic distributor
(for Scénic II)).
When replacing the torque converter, ensure that the
reaction shaft is securely attached to the hub of the
oil pump (flanged shaft).
Note:
A setting point which is too low may be due to a lack
of engine power. Does the engine speed change each time
there is a gear change?

The checks carried out have not provided any
evidence of a fault and the automatic
transmission appears to be working correctly.
If the vehicle does show the customer complaint
selected, continue with the entire fault finding
procedure. Replace the hydraulic distributor and all the solenoid
valves. (see MR 364 Mechanical, 23A, Automatic
transmission, Hydraulic distributor
(for Mégane II) and MR 370 Mechanical, 23A,
Automatic transmission, Hydraulic distributor
(for Scénic II)).
B
NOYES
YESNO
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

AUTOMATIC TRANSMISSION
Fault finding – Fault Finding Chart23A
23A -121V4 MR-372-J84-23A050$924.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ALP5 Erratic gear changes
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Carry out a road test using the diagnostic tool, making sure that status ET013 Gear engaged operates normally.
If the customer complaint occurs with the brake pedal released, check that status ET004 Brake light switch
(Closed) is NO.
If not, adjust the brake light switch and the brake pedal.
Make sure that the instrument panel display of the gear engaged matches the gear lever position.
Check the automatic transmission wiring harness (sequence solenoid valve control).
Replace it if necessary.
Check that the gear lever cable is working properly and adjust it if necessary.
Check that the multifunction switch is working correctly.
If the fault is still present, replace the multifunction switch.
Carry out fault finding on the injection system.
Check engine speed signal PR006 during a road test at a steady speed.
If the signal is wrong, replace the engine speed sensor.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2000_V10_ALP5/DP0TA2000_V11_ALP5/DP0TA2000_V15_ALP5

AUTOMATIC TRANSMISSION
Fault finding – Fault Finding Chart23A
23A -122V4 MR-372-J84-23A050$924.mif
SIEMENS TA2000
Vdiag No.: 10-11-15
ALP6 Reversing lights do not work
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Check:
–the condition of the fuses in the UPC.
–the condition of the bulbs.
–the condition of the bulb contacts. Repair if necessary.
–Check that the earth is present for the following connections:
●Connection code MAQ of component 172.
●Connection code MZ of component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Switch off the ignition and disconnect the modular connector.
Switch on the ignition again and check for + 12 V after ignition feed on connection AP11 of component 485.
Switch off the ignition and check the continuity on the following connections, with the gear lever in position R:
●Connection code H66P between components 485 and 1337.
●Connection code AP11 between components 485 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the gear lever cable is correctly adjusted and check the instrument panel display.
If the continuity is faulty, replace the multifunction switch.
Switch on the ignition.
With the gear lever in position R, check for + 12 V after ignition feed on the following connections:
●Connection code H66P between components 172 and 1337.
●Connection code H66P between components 173 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2000_V10_ALP6/DP0TA2000_V11_ALP6/DP0TA2000_V15_ALP6