phone RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Network Interface Unit BIC Workshop Manual

86D-11V1 MR-372-J84-86D050$040.mif
86D
BIC
Vdiag No.: 14
Layout of the main components of the LPN* Radio system:
Diagnostic socket
V M CAN
Other computersMultimedia network
interface unit
Steering column
control
GPS aerial LPN radio navigation
Passenger
compartment fuse box
and relay
Aerial amplifier
Radio navigation
display
ABS, ABS/ESP or
wheel speed
computer
depending on
equipment level
Microphone
CD changer
(depending on
equipment)Speakers
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Operating diagram

86D-13V1 MR-372-J84-86D050$050.mif
86D
BIC
Vdiag No.: 14
General operation
The multimedia system is involved in the following functions:
–Radio reception (AM, FM).
–Playing CDs/MP3 CDs/navigation map.
–Guidance and navigation system with colour screen.
–Bluetooth hands-free phone.
The use of this multimedia system allows the customer:
–To select radio stations by using the preselections, the list or manual selection.
–To have an automatically-updated radio list.
–To listen to CDs or MP3 CDs.
–To control the radio using the radio control satellite.
–To change various acoustic parameters (bass, treble, fader, etc.).
–To navigate on a colour screen (visual and audio guidance): for this function the system uses GPS, the vehicle
speed wire information and an internal gyroscope.
–To receive traffic information via RDS-TMC and to display it on the navigation map.
–To display the time and temperature on the screen.
–To use the hands-free phone function (sound relayed to the radio speakers) with a Bluetooth phone (HFP profile).
–To be protected by an immobiliser code.
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Function

86D-27V1 MR-372-J84-86D050$100.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION (continued)
*LPN: Low Price Navigation
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
ButtonET009:Repeat button (only
on Scénic II Phase 2)
PRESSED
RELEASEDIn the event of an inconsistency,
consult the interpretation of
status ET009.
ET020:"Mute" buttonIn the event of an inconsistency,
consult the interpretation of
status ET020.
ET011:+ buttonIn the event of an inconsistency,
consult the interpretation of
status ET011.
ET012:- buttonIn the event of an inconsistency,
consult the interpretation of
status ET012.
ET023:Source buttonIn the event of an inconsistency,
consult the interpretation of
status ET023.
ET025:Telephone buttonIn the event of an inconsistency,
consult the interpretation of
status ET025.
ET024:Mode button In the event of an inconsistency,
consult the interpretation of
status ET024.
Wheel actionET017:Wheel actionUPWARDS
DOWNWARDS
INACTIVEIn the event of an inconsistency,
consult the interpretation of
status ET017.

86D-29V1 MR-372-J84-86D050$110.mif
86D
BIC
Vdiag No.: 14
Tool status Diagnostic tool title
ET002Radio on/off button
ET004+12 V Side lights
ET007Brightness
ET009Repeat button (only on Scénic II Phase 2)
ET011+ button
ET012- button
ET017Wheel action
ET020"Mute" button
ET023Source button
ET024Mode button
ET025Telephone button
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Status summary table

86D-30
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-372-J84-86D050$120.mif
86D
BIC
Vdiag No.: 14
ET009
ET011
ET012
ET020
ET023
ET024
ET025REPEAT BUTTON
+ BUTTON
- BUTTON
MUTE BUTTON
SOURCE BUTTON
MODE BUTTON
TELEPHONE BUTTON
STATUS DEFINITIONPRESSED: This means that the button is pressed.
RELEASED: This means that the button is released.
NOTESThere must be no present or stored faults.
Note: ET009 Repeat button is not present on the Espace IV Phase 2.
Use the Wiring Diagrams Technical Note for Espace IV Phase 2 or Scénic II
Phase 2.
Check the condition and connection of the radio control satellite connector, component code 1519 (for Scénic II
Phase 2) or component code 325 (for Espace IV Phase 2) and the multimedia network interface unit connector,
component code 1714.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
BIC_V14_ET009 / BIC_V14_ET011 / BIC_V14_ET012 / BIC_V14_ET020 / BIC_V14_ET023 / BIC_V14_ET024 / BIC_V14_ET025
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Interpretation of statuses

86D-42
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-372-J84-86D050$160.mif
MULTIMEDIA NETWORK INTERFACE UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 3 Steering column switch fault
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Refer to the Conformity check and to the interpretation of the following statuses:
–ET002 Radio on/off button,
–ET004 +12 V Side lights,
–ET007 Brightness,
–ET009 Repeat button (only on Scénic II Phase 2),
–ET011 + button,
–ET012 - button,
–ET017 Wheel action,
–ET020 Mute button,
–ET023 Source button,
–ET024 Mode button,
–ET025 Telephone button.
BIC_V14_ALP3