engine RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Owner's Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 391
Page 125 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -125
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -125V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub:function: Starting
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
StartingET070:Start buttonDEPRESSED
RELEASED In the event of a fault,
consult the
interpretation of status
ET070.
ET108:Automatic gearbox
lever positionNOT IN NEUTRAL
P
NEUTRAL, REVERSEIn the event of a fault,
consult the
interpretation of status
ET108.
ET048:Clutch pedal
positionDEPRESSED
RELEASEDIn the event of a fault,
consult the
interpretation of status
ET048.
ET047:Brake pedal positionUNDETERMINED
RELEASED
DEPRESSED
INCONSISTENCY In the event of a fault,
consult the
interpretation of status
ET047.
ET110:UCH request to
injection or
Protection and
Switching UnitENGINE OFF
INACTIVE
APC
STARTING In the event of a fault,
consult the
interpretation of status
ET110.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
Page 126 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -126
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -126V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: AIR CONDITIONING
Sub-function: User selection
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
User
selectionET029:Air conditioning
buttonDEPRESSED
RELEASED In the event of a fault,
refer to the
interpretation of status
ET029.
ET028:Heated rear screen
buttonPRESSED if the "heated rear
screen" button on the air
conditioning control panel is
pressed.
RELEASED otherwise.In the event of a fault,
refer to the
interpretation of status
ET028.
ET015:Passenger
compartment blowerACTIVE
INACTIVE
Note:
This status is only operative
for manual air conditioning
systems (and heater versions
without air conditioning).In the event of a fault,
refer to the
interpretation of status
ET015.
Page 127 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -127
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -127V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: AIR CONDITIONING
Sub-function: Heating
*RCH = Passenger Compartment Heating Resistor
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
HeatingPR001:Battery voltage9 V < X < 16 V In the event of a fault,
consult the
interpretation of
parameter PR001.
PR002:External
temperature Temperature in ˚CIn the event of a fault,
consult the
interpretation of
parameter PR002.
ET017:Number of RCH*
required0, 1, 2, 3, 4 or 5In the event of a fault,
consult the
interpretation of status
ET017.
ET018:Number of RCH*
authorised by
alternator0, 1, 2, 3, 4 or 5In the event of a fault,
consult the
interpretation of
status ET018.
ET019:Number of RCH*
authorised by
injection computer0, 1, 2, 3, 4 or 5In the event of a fault,
consult the
interpretation of status
ET019.
ET015:Passenger
compartment fan ACTIVE
INACTIVE
Note:
This status is only operative
for manual air conditioning
systems (and heater versions
without air conditioning). In the event of a fault,
refer to the
interpretation of status
ET015.
Page 128 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -128
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -128V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: AIR CONDITIONING
Sub-function: Heating (continued)
*RCH = Passenger Compartment Heating Resistor
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
HeatingET020:Number RCH*
activated.0, 1, 2, 3, 4 or 5In the event of a fault,
refer to the
interpretation of status
ET020.
ET021:RCH* 1 relay control ACTIVE
INACTIVE In the event of a fault,
consult the
interpretation of
status ET021.
ET022:RCH* 2 relay controlACTIVE
INACTIVE In the event of a fault,
consult the
interpretation of
status ET022.
ET023:RCH* 3 relay controlACTIVE
INACTIVEIn the event of a fault,
consult the
interpretation of
status ET023.
ET031:Fast idle speed
request for RCH*INACTIVE
Fast idle speed to prevent
battery dischargeIn the event of a fault,
consult the
interpretation of status
ET031.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET025:Retractable roofCLOSED
NOT CLOSED
ABSENTIn the event of a fault,
consult the
interpretation of status
ET025.
ET026:Heated rear screen
switchACTIVE
INACTIVEIn the event of a fault,
consult the status
interpretation ET026.
Page 129 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -129
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -129V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: AIR CONDITIONING
Sub-function: Cold Loop
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Cold loopET030:Air conditioning
request 2ACTIVE
INACTIVEIn the event of a fault,
consult the
interpretation of status
ET030.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET015:Passenger
compartment fan ACTIVE
INACTIVE
Note:
This status is only operative
for manual air conditioning
systems (and heater versions
without air conditioning). In the event of a fault,
refer to the
interpretation of status
ET015.
PR002:External
temperature Temperature in ˚CIn the event of a fault,
consult the
interpretation of
parameter PR002.
Page 130 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -130
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -130V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre receiver ET040:Tyre pressure
monitoring systemNOT WORKING
ACTIVE If status ET040 is OUT OF
ORDER, consult the fault
finding procedure for status
ET040.
ET032:Front left-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
PUNCTURE
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET032 is not OK,
consult the fault finding
procedure for status ET032.
PR003:Front left-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR003.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR019:Front left-hand tyre
temperature- 40ºC
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.
ET0033:Front right-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET033 is not OK,
consult the fault finding
procedure for status ET033.
Page 131 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -131
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -131V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval (continued 1)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre approval PR004:Front right-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR004.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR020:Front right-hand tyre
temperature- 40ºC
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.
ET034:Rear right-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET034 is not OK,
consult the fault finding
procedure for status ET034.
PR005:Rear right-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR005.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR021:Rear right-hand tyre
temperature- 40ºC
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.
Page 132 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval (continued 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre approval ET035:Rear left-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET035 is not OK,
consult the fault finding
procedure for status ET035.
PR006:Rear left-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR006.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR022:Rear left-hand tyre
temperature- 40ºC
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.
Page 133 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -133
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -133V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre management
fr*: front,
rr*: rear.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre
management PR009:Fr* wheel low speed
recommended
pressure.
In barCheck that the values entered
are actually the recommended
ones (see MR 364 (Mégane II)
or MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
Otherwise, enter the
recommended pressures using
command VP005 Write
recommended pressures. PR010:Rr* wheel low speed
recommended
pressure.
PR012:Fr* wheel high speed
recommended
pressure.
PR011:Rr* wheel high
speed
recommended
pressure.
PR014:Left/right pressure
difference threshold0.5 bar
None. PR015:Low under-inflation
threshold- 0.4 bar
PR059:Puncture report
threshold- 0.6 bar
PR017:Cold over-inflation
threshold0.7 bar
PR018:Warm over-inflation
threshold0.8 bar
Page 134 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -134
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -134V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre display
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre displayET039:STOP warning light
on request ACTIVE
INACTIVEACTIVE, if a puncture is
detected.
There is a buzzer
activation request for all
severity level 1
warnings (puncture).
The buzzer emits a
single beep when a fault
occurs.
ET016:Buzzer activation
requestINACTIVE
STATUS 1
STATUS 2
INCONSISTENCY STATUS 1: request for
buzzer activation when
a puncture is detected.
STATUS 2: request for
buzzer activation to
warn the driver that the
vehicle speed is too
high when the vehicle
has one or more
punctured tyres. This
information is only valid
on vehicles fitted with
PAX System tyres.