dashboard RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Workshop Manual

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 318
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 318V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP16No passenger window operation
(Driver and passenger one-touch electric windows)
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, see 87D Electric windows -
Sunroof, Fault finding chart.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Remove the passenger's window winder switch (see MR 364 (Mégane II) or MR 370 (Scenic II) Mechanical
systems, 87D, Electric windows - Sunroof, Front window winder switch on passenger's door: Removal -
Refitting) and disconnect its connector.
Shunt connections 22A and MAN of component 133 to lower the window and to raise the window shunt
connections 22B and MAN of component 133.
Does the window move?
YES NO
Replace the passenger's window winder switch
(see MR 364 (Mégane II) or MR 370 (Scenic II)
Mechanical systems, 87D, Electric windows -
Sunroof, Front window winder switch on
passenger's door: Removal - Refitting).
Check that the right-hand dashboard cross member
earth is in good condition and correctly secured to
the chassis.
If the earth is not in good condition, clean and
retighten the terminal.
If the earth is faulty, replace the wiring.
Check the continuity of the following connection:
●Connection code BP70 between components 204 and 260.
Check the intermediate connectors and the fuse if there is a continuity or supply fault.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the
wiring.
Check for earth on connection MAN of
component 204.
Is the earth correct?
NO YES
Connect a voltmeter across
connections BP70 and MAN of
component 204.
Does the voltmeter display the
correct supply?
NO YES
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP16 /UCH_V48_ALP16/UCH_V4C_ALP16/
UCH_V4D_ALP16/UCH_V4F_ALP16/UCH_V50_ALP16

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 323
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 323V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP18No driver's window operation
(Driver and passenger electric windows)
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, see 87D Electric windows -
Sunroof, Fault finding chart.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Remove the driver's window winder switch (see MR 364 (Mégane II) or MR 370 (Scenic) Mechanical systems,
87D, Electric windows - Sunroof, Front window winder switch on driver's door: Removal - Refitting) and
disconnect its connector.
Check for + 12 V on connection 21C of component 1512.
Is the feed correct?
YES NO
Shunt track 5 of the white driver's electric window
switch connector with track 5 of the black driver's
electric window switch connector and shunt
connections 21E and MAM of component 1512 to
lower the window (to raise the window, shunt track 5
of the white driver's electric window switch
connector with track 4 of the white driver's electric
window switch connector and shunt
connections 21C and MAM of component 1512).
Does the window move?
YES
Replace the driver's electric window switch
(see MR 364 (Mégane II) or MR 370 (Scenic II)
Mechanical systems, 87D, Electric windows -
Sunroof, Front electric window switch on
driver's door: Removal - Refitting).
Check that the left-hand dashboard cross member earth
is in good condition and correctly secured to the chassis.
If the earth is not in good condition, clean and retighten
the terminal.
If the earth is faulty, replace the wiring.
NO
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP18 /UCH_V48_ALP18/UCH_V4C_ALP18/
UCH_V4D_ALP18/UCH_V4F_ALP18/UCH_V50_ALP18

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 326
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 326V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP19
CONTINUED 1
Check for earth on connection MAS of
component 1512.
Is the earth correct?
NO YES
Check that the left-hand dashboard cross member
earth is in good condition and correctly secured to
the chassis.
If the earth is not in good condition, clean and
retighten the terminal. If the earth is faulty, replace
the wiring.
Check the continuity on the following connection:
●Connection code BP55 between
components 203 and 260.
If the continuity is faulty, check the intermediate
connector.
If the connector is faulty and if there is a repair
procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the connector; otherwise, replace the wiring.
NOCheck for earth on connection 22D of
component 1512.
Is the earth correct?
YES
NOCheck for + 12 V on connection BP55 of
component 1512.
Is the feed correct?
YES
AFTER REPAIRCarry out a complete check using the diagnostic tool.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 329
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 329V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP20
CONTINUED 1
Check for earth on connection MAS of
component 1512.
Is the earth correct?
NO YES
Check that the left-hand dashboard cross member
earth is in good condition and correctly secured to
the chassis.
If the earth is not in good condition, clean and
retighten the terminal. If the earth is faulty, replace
the wiring.
Check the continuity on the following connection:
●Connection code BP55 between
components 203 and 260.
If the continuity is faulty, check the intermediate
connector.
If the connector is faulty and if there is a repair
procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the connector; otherwise, replace the wiring.
NOCheck for earth on connection MAS of
component 152.
Is the earth correct?
YES
NOCheck for + 12 V on connection BP55 of
component 203.
Is the feed correct?
YES
AFTER REPAIRCarry out a complete check using the diagnostic tool.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 335
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 335V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP23No electric window operation
(Driver's and passengers' electric windows)
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, see 87D Electric windows -
Sunroof, Fault finding chart.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Remove the driver's window winder switch (see MR 364 (Mégane) or MR 370 (Scenic) Mechanical systems,
87D, Electric windows - Sunroof, Front window winder switch on driver's door: Removal - Refitting) and
disconnect its connector.
Check for + 12 V between track 5 of the driver's window winder switch white connector and track 4 of the driver's
window winder black connector.
Is the feed correct?
YES NO
Replace the driver's electric window switch
(see MR 364 (Mégane) or MR 370 (Scenic)
Mechanical systems, 87D, Electric windows -
Sunroof, Front electric window switch on
driver's door: Removal - Refitting).
Check that the left-hand dashboard cross member
earth is in good condition and secured correctly.
If the earth is not in good condition, clean and
retighten the terminal. If the earth is faulty, replace
the wiring.
If the fault is still present, contact the Techline.
Check for + 12 V between connection track 5 of the
driver's window winder switch white connector and
the chassis earth.
Is the feed correct?
YES NO
Check the continuity on the following connection:
●Connection code 21K between
components 203 and 645.
If the continuity is faulty, check the intermediate
connector.
If the connector is faulty and if there is a repair
procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the connector; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP23 /UCH_V48_ALP23/UCH_V4C_ALP23/
UCH_V4D_ALP23/UCH_V4F_ALP23/UCH_V50_ALP23

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 337
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 337V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP24
CONTINUED 1
Check for + 12 V on connection BP93 of component 304.
Is the feed correct?
YES NO
Use the diagnostic tool to read the faults in the
UCH.
Is fault DF031 One touch window connection
present?
YES NO
Check the continuity, insulation and the
absence of the interference resistance to
+ 12 V and to earth of the following connection:
●Connection code 21K between
components 304 and 645.
If the continuity is faulty, check the
intermediate connectors.
If one of the connectors is faulty and there is a
repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions
for repair), repair the connector, otherwise
replace the wiring.
If the fault is still present, contact the Techline.
Check the continuity on the following connection:
●Connection code BP93 between
components 304 and 260.
●Connection code MAM between
component 304 and Left-hand dashboard/
cross member earth.
If one of the continuities is faulty, check the
intermediate connector.
If a connector is faulty and there is a repair
procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.