fuse RENAULT SCENIC 2009 J84 / 2.G Air Conditioning Climate Control Workshop Manual

62B - 5
CLIMATE CONTROL
Fault finding – Introduction62B
V3 MR-372-J84-62B000$010.mif
4. FAULT FINDING PROCEDURE
Check the battery charge and the
condition of the fuses
Print the system fault finding log
(available on CLIP and in the
Workshop Repair Manual or
Technical Note)
Connect CLIP
Dialogue
with Electronic
Control Unit?no
yes
Read the faults
Faults
presentno
yes
Deal with present faults
Deal with stored faults
The cause is
still presentnoFault
solved
yes
Conformity check
The cause is
still presentnoFault
solved
Use the fault finding
charts
The cause is
still presentnoFault
solved
Contact Techline with the
completed fault finding log
Vdiag No.: 44
See ALP 1
ACREG X84 1.1
Edition 2

62B - 9
CLIMATE CONTROL
Fault finding – Allocation of computer tracks62B
V3 MR-372-J84-62B000$030.mif
Vdiag No.: 44
CLIMATE CONTROL
Fault finding – Allocation of computer tracks
Allocation of climate control computer tracks.
Computer
tracksFunctions Sensor - actuator tracks
Connector A
1CAN L
2not used
3not used
4solar sensor signal track 2 of the solar sensor
5interior temperature sensor signal track 4 of the interior temperature sensor
6computer earth
7CAN H
8not used
9+ 12 V side lightsleft-hand side light fuse in the Protection and Switching
Unit (7.5 A)
10 + 12 V accessories feed passenger compartment fuse (15 A)
11 + 12 V before ignition feed passenger compartment fuse (20 A)
12 0 V sensors (solar, interior temperature)track 1 of the solar sensor and track 5 of the interior
temperature sensor
Connector B
1recirculation motor control track 5 of the recirculation motor
2not used
3not used
4not used
5not used
6not used
7passenger compartment blower module
controltrack 6 of the passenger compartment blower module
6-track connector
812 V supply of the mixing and distribution
motorstrack 2 of the mixing and distribution motors
9not used
10 recirculation motor control track 6 of the recirculation motor
11 distribution motor control track 1 of the distribution motor (coil B2)
12 distribution motor control track 6 of the distribution motor (coil A2)
13 distribution motor control track 3 of the distribution motor (coil B1)
14 distribution motor control track 4 of the distribution motor (coil A1)
15 mixing motor controltrack 1 of the mixing motor for B and C84 and track 3
of the mixing motor for J84 (B2 winding)
16 mixing motor control track 6 of the mixing motor (A2 winding)
17 mixing motor controltrack 3 of the mixing motor for B and C84 and track 1
of the mixing motor for J84 (B1 winding)
18 mixing motor control track 4 of the mixing motor (A1 winding)
ACREG X84 1.1
Edition 2
MR-372-J84-62B000$030.mif

62B - 10
CLIMATE CONTROL
Fault finding – Configurations and programming62B
V3 MR-372-J84-62B000$040.mif
Vdiag No.: 44
CLIMATE CONTROL
Fault finding – Configurations and programming
CLIMATE CONTROL COMPUTER CONFIGURATION:
The climate control computer has 2 configuration functions. These configurations need to be set after the computer
has been replaced.
These two configurations are important as they ensure air conditioning is optimised within the vehicle (better control
of automatic climate control). If they are not correctly entered, cold air and warm air production will be severely
affected (e.g. heating resistors will not be switched on to heat the passenger compartment air).
These configurations can be accessed in repair mode by the diagnostic tool and can only be entered using
the fault finding by computer menu as opposed to the fault finding by function menu.
These configurations can be read, also using the diagnostic tool in repair mode to ensure they have been correctly
set. Configurations can be read in both fault finding by computer mode and fault finding by function mode.
–The first configuration is CF044 Vehicle type; this configuration allows you to enter the body type to which the
climate control computer is fitted (J84/R84 for 4 wheel drive Mégane Scénic and Scénic, and OTHER X84 for all
other Méganes). The configuration reading is called: LC013 Vehicle type.
–The second configuration is CF117 Type of heating resistors; this configuration is used to enter the type of
passenger compartment air heating resistors fitted in the vehicle. There are three options: WITHOUT for vehicles
without 1000 W and 1800 W resistors.
Heating resistors are mainly fitted on vehicles with Diesel engines.
They are located in the ventilation - air distribution unit (left-hand side), next to the heater matrix. The label affixed
to the resistor unit (with the part number) specifies whether the resistors are 1000 or 1800 W (Note: 1800 W
resistors are mainly fitted to Mégane Scénics). This configuration reading is called: LC043 Heating resistor.
Note:
In fault finding by function mode, the diagnostic tool can also display the configuration readings of the other computers
involved in the air conditioning function. All configurations of the air conditioning function (injection computer, UCH
and Protection and Switching Unit) are listed in Section 62A Air conditioning.
MIXING
AND DISTRIBUTION MOTOR PROGRAMMING PROCEDURE (self-setting):
There is no specific programming operation for the mixing motor and the distribution motor.
However, the minimum and maximum limits of these motors have to be programmed. This operation is automatic and
is performed in the following cases:
–after replacing the mixing or distribution motor,
–after disconnecting the battery or after disconnecting the climate control computer supply fuse,
–if a fault, declared as present when the ignition was switched off, disappears the next time the ignition is switched
on.
IMPORTANT
To ensure this programming operation is performed correctly, the passenger compartment blower must be

switched off (speed set to 0).
ACREG X84 1.1
Edition 2
MR-372-J84-62B000$040.mif

62B-14
CLIMATE CONTROL
Fault finding – Interpretation of faults62B
V3 MR-372-J84-62B000$060.mif
Vdiag No.: 44
CLIMATE CONTROL
Fault finding – Interpretation of faults
DF001
PRESENT
OR
STOREDCOMPUTER
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
Apply this fault finding procedure if the fault appears as present or stored again after:
–clearing the fault and switching the ignition off then back on.
If the fault is stored: clear the fault, switch off the ignition and disconnect the climate control computer supply
fuse.
–Refit the fuse and switch the ignition back on.
–Start the engine and switch on the air conditioning.
If the fault reappears as stored: contact your Techline.
If the fault does not reappear: leave the air conditioning switched on and select various ventilation and air
distribution settings to check that the system is working correctly.
If the fault is present: contact your Techline.
AFTER REPAIRIf the computer has been replaced (at the request of the Techline): reconfigure the
computer (see section Configurations and Programming).
Deal with any other faults.
ACREG X84 1.1
Edition 2
MR-372-J84-62B000$060.mif

62B - 22
CLIMATE CONTROL
Fault finding – Interpretation of statuses62B
V3 MR-372-J84-62B000$070.mif
Vdiag No.: 44
CLIMATE CONTROL
Fault finding – Interpretation of statuses
ET007
COMPUTER + AFTER IGNITION FEED
NOTESNone.
This status shows the + 12 V after ignition feed supplied by the Protection and Switching Unit.
When the ignition is off, the status displays: ABSENT.
When the ignition is on, the status displays: PRESENT.
If the fault is still present, carry out fault finding on the Protection and Switching Unit: Check that status
ET003 After ignition relay control is working correctly and check that fault DF001 After ignition relay control
circuit is not present.
Carry out any repairs necessary (see corresponding fault finding procedures).
If the fault is still present: disconnect connector A (12-track) from the climate control computer to check the
insulation, continuity and absence of interference resistance of the following connections:
Computer connector A track 10 + accessories feed (7.5 A fuse in the Protection and
Switching Unit)
Computer connector A track 11 + before ignition feed (20 A fuse of the UCH)
Computer connector A track 6 Earth (left-hand dashboard beam)
Repair if necessary.
If the connections are correct and the climate control computer is correctly supplied but the fault is still present:
carry out fault finding on the electric charge circuit.
AFTER REPAIRRepeat the conformity check from the start.
ACREG X84 1.1
Edition 2
MR-372-J84-62B000$070.mif

62B - 33
CLIMATE CONTROL
Fault finding – Interpretation of parameters62B
V3 MR-372-J84-62B000$080.mif
Vdiag No.: 44
PR092
BATTERY VOLTAGE
NOTESNone.
This parameter specifies the supply voltage of the climate control computer.
This parameter should indicate a voltage equal to: 10.5 < X < 14.4 V.
If the voltage is not within the specified range, disconnect connector A (12-track) of the climate control
computer to check the insulation, continuity and absence of interference resistance of the connections:
Computer connector A track 10 + accessories feed (7.5 A fuse in the Protection and
Switching Unit)
Computer connector A track 11 + before ignition feed (20 A fuse of the UCH)
Computer connector A track 6 Earth (left-hand dashboard beam)
Repair if necessary.
If the connections are correct but the fault still persists, perform fault finding on the charging circuit.
AFTER REPAIRRepeat the conformity check from the start.
ACREG X84 1.1
Edition 2

62B-43
CLIMATE CONTROL
Fault finding – Fault Finding Chart62B
V3 MR-372-J84-62B000$110.mif
Vdiag No.: 44
CLIMATE CONTROL
Fault finding – Fault Finding Chart
ALP 1 No dialogue with the computer
NOTESNone.
Try the diagnostic tool on another vehicle.
Check:
–the connection between the diagnostic tool and the diagnostic sensor (wiring in good condition),
–the connection between the vehicle's diagnostic sensor and the diagnostic socket (cable in good condition),
–the injection, engine and passenger compartment fuses.
Check for + 12 V battery on track 16, and + 12 V after ignition feed on track 1 and an earth on track 5 and
on track 4 of the diagnostic socket.
Repair if necessary.
Disconnect the connector from the climate control computer in order to check the insulation, continuity and
the absence of interference resistance of the following connections:
Climate control computer 12-track connector:
Track 11 + before ignition (see the vehicle wiring diagram)
Track 10 + accessories feed (see the vehicle wiring diagram)
Track 6 Earth
Track 7 Track 6 of the diagnostic socket (CAN H)
Track 1 Track 14 of the diagnostic socket (CAN L)
Repair if necessary (see the vehicle wiring diagram).
AFTER REPAIRPerform a complete check using the diagnostic tool.
ACREG X84 1.1
Edition 2

62B-50
CLIMATE CONTROL
Fault finding – Fault Finding Chart62B
V3 MR-372-J84-62B000$110.mif
Vdiag No.: 44
ALP 5 No passenger compartment ventilation
NOTESOnly consult this customer complaint after a complete check using the
diagnostic tool.
Special notes:
The 2 x 5-track intermediate connector is located on the LH side of the distribution /
ventilation unit (behind a plastic cover) and the passenger compartment fan control
module is located slightly higher up, below the heater matrix pipes.
Check that the fusesare in good condition.
Using the diagnostic tool, check that the passenger compartment fan
control setting given by the computer varies from 0 to 100% by checking
parameter PR019 Passenger compartment fan PWM setpoint
(refer to the interpretation of this status).
Does the value vary?
YES
Check that the control voltage (PWM) (modulated control voltage) of the passenger
compartment fan power module varies between 5 and 12 V (from 0 to 100%) by
measuring between track 6 of the module's 6-track connector and earth
(connector connected).
Note:
The check procedure is given in the Help section.
Does the voltage vary correctly?
NO
Check the insulation, continuity and absence of interference resistance on the
following connection:
Air conditioning computer 18-track
connector
track 7
Repair if necessary.Power module 6-track connectortrack 6
With the ignition on, check for +12 V accessories feed on track B1 and an earth on track B5
of the black 2 x 5 track intermediate connector (screwed to the base of the console).
Repair if necessary.
NO
YES Contact your
TECHLINE.
AFTER REPAIRPerform a complete check using the diagnostic tool.
ACREG X84 1.1
Edition 2