RENAULT SCENIC 2009 J84 / 2.G Air Conditioning Manual Conditioning Owner's Manual
Manufacturer: RENAULT, Model Year: 2009, Model line: SCENIC, Model: RENAULT SCENIC 2009 J84 / 2.GPages: 23
Page 21 of 23
MANUAL AIR CONDITIONING
Fault finding – Fault Finding Chart62C
62C-21V2 MR-372-J84-62C000$040.mif
ALP 13 No control panel lighting
NOTESNone.
Check that the fuses are in good condition.
Repair if necessary.
Check that the bulbs are sound.
Repair if necessary.
Check for the presence of an earth on track B5 and track A1 of the control panel.
Repair if necessary.
With the side lights switched on, ensure that there is + 12 V side light supply on track B2 of the control panel.
Repair if necessary.
If the fault persists, contact your Technline
AFTER REPAIRCheck that the system is operating correctly.
Page 22 of 23
MANUAL AIR CONDITIONING
Fault finding – Fault Finding Chart62C
62C-22V2 MR-372-J84-62C000$040.mif
ALP 14 Air conditioning noises during operation
NOTESOnly deal with this customer complaint after a full check with the diagnostic tool
(fault reading and configuration checks).
Check that the computers involved in the air conditioning function (Injection, Protection and Switching Unit,
UCH and Air conditioning control panel) are correctly configured.
Reconfigure if necessary (see 62A, Air conditioning, Configurations and Configuration reading).
Check that:
–the compressor fitted to the vehicle corresponds correctly to the engine (see MR 370 Mechanical, 62A, Air
conditioning, Air conditioning: Parts and consumables for the repair).
Replace the compressor if necessary (see MR 370, Mechanical, 62A, Air conditioning, Compressor:
Removal - Refitting).
–the compressor is correctly fixed (see MR 370 Mechanical, 62A, Air conditioning, Compressor: Removal -
Refitting).
Check the condition of the compressor belt and check its tension. Replace the belt if necessary (see MR 370
Mechanical, 11A, Top and front of engine, Accessories belt: Removal - Refitting).
Check that the intermediate pipes, condenser and dehydrator reservoir are correctly fitted.
–Check the mountings and brackets of the components.
–Check the contact between and proximity of the components.
(see MR 370 Mechanical, 62A, Air conditioning, Air conditioning: List and location of components).
Check the correct operation of the cooling fan assembly or passenger compartment fan assembly and
condenser:
–check the electrical supply of the fan using parameters ET007 High speed fan assembly control, AC009 Low
speed fan assembly and AC010 High speed fan assembly (see 62A, Air conditioning, Conformity check,
Cold loop sub-function).
Check the quantity of refrigerant (see MR 370 Mechanical, 62A, Air conditioning, Air conditioning: Parts
and consumables for the repair).
If the quantity of refrigerant is:
–Greater than the manufacturer's information, recharge according to the manufacturer's values (see MR 370
Mechanical, 62A, Air conditioning: Draining - Filling).
–Less than the manufacturer's information, check for leaks (see MR 370 Mechanical, 62A, Air conditioning,
Refrigerant circuit: Check).
If the fault is still present, replace the compressor (see MR 370, Mechanical, 62A, Air conditioning,
Compressor: Removal - Refitting).
AFTER REPAIRCarry out a complete check using the diagnostic tool.
Page 23 of 23
MANUAL AIR CONDITIONING
Fault finding – Fault Finding Chart62C
62C-23V2 MR-372-J84-62C000$040.mif
ALP 15 Passenger compartment ventilation noises
NOTESOnly deal with this customer complaint after a full check with the diagnostic tool
(fault reading and configuration checks).
The aim of the following operations is to check and, if necessary, eliminate any foreign bodies (leaves,
insects, other, etc.) in:
–the passenger compartment air inlet,
–the cabin filter housing,
–the housing and on the fan assembly.
Check the passenger compartment air inlet and the cabin filter housing:
Remove:
–the scuttle panel grille (see MR 371 Bodywork, 55A, Exterior equipment, Scuttle panel grille: Removal -
Refitting),
–the air filter access panel,
–the scuttle panel partition,
–the cabin filter.
Check that there are no foreign bodies (leaves, insects, other, etc.) and, if necessary, clean the passenger
compartment air inlet and the cabin filter housing.
Refit:
–the cabin filter,
–the scuttle panel partition,
–the air filter access panel,
the scuttle panel grille (see MR 371 Bodywork, 55A, Exterior equipment, Scuttle panel grille: Removal -
Refitting).
Check the housing and the fan assembly:
Remove the fan assembly (see MR 370 Mechanical, 61A, Heating, Fan assembly: Removal - Refitting).
Check that there are no foreign bodies (leaves, insects, other, etc.) and, if necessary, clean the fan assembly
housing.
Check that there are no foreign bodies (leaves, insects, other, etc.) and, if necessary, clean the fan assembly.
Refit the fan assembly (see MR 370 Mechanical, 61A, Heating, Fan assembly: Removal - Refitting).
AFTER REPAIRCarry out a complete check using the diagnostic tool.