ESP RENAULT SCENIC 2009 J84 / 2.G Automatic Transmission AJ0 BVA Owner's Manual

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 142V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR106
EFFECTIVE ENGINE TORQUE
Note:
Parameter PR106 "Effective engine torque" applies to the following sub-functions:
"Gear changes".
"Torque activation".
PARAMETER
DEFINITIONThis parameter indicates the effective engine torque in Nm. This signal is supplied to
the gearbox computer by the injection computer.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine ignition on and engine running at idle speed.
PR006 "Engine
speed"PR007 "Turbine
speed"PR106 "Effective
engine torque"PR153 "Slow
torque"PR154 "Fast
torque"
0 rpm 0 rpm 140 Nm 360 Nm - 32 Nm
≈ 802 rpm≈ 704 rpm≈ 34 Nm≈ 360 Nm≈ - 30 Nm
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR106/AJ0_V05_PR106

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 143V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR153
SLOW TORQUE SETPOINT
Note:
Parameter PR153 "Slow torque setpoint" applies to the following sub-function:
"Slow torque activation".
PARAMETER
DEFINITIONThis parameter indicates the slow torque setpoint in Nm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine ignition on and engine running at idle speed.
PR006 "Engine
speed"PR007 "Turbine
speed"PR106 "Effective
engine torque"PR153 "Slow
torque"PR154 "Fast
torque"
0 rpm 0 rpm 140 Nm 360 Nm - 32 Nm
≈ 802 rpm≈ 704 rpm≈ 34 Nm≈ 360 Nm≈ - 30 Nm
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR153/AJ0_V05_PR153

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 144V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR154
FAST TORQUE SETPOINT
Note:
Parameter PR154 "Fast torque setpoint" applies to the following sub-function:
"Torque activation".
PARAMETER
DEFINITIONThis parameter indicates the fast torque setpoint in Nm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine ignition on and engine running at idle speed.
PR006 "Engine
speed"PR007 "Turbine
speed"PR106 "Effective
engine torque"PR153 "Slow
torque"PR154 "Fast
torque"
0 rpm 0 rpm 140 Nm 360 Nm - 32 Nm
≈ 802 rpm≈ 704 rpm≈ 34 Nm≈ 360 Nm≈ - 30 Nm
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR154/AJ0_V05_PR154

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart
23A
23A - 157V3 MR-372-J84-23A000$945.mif
AJ0 BVA
Vdiag No.: 04, 05
ALP1
CONTINUED
Check for + 12 V on connection BP42 of component 119.
Check for + after ignition feed on connection AP4 of component 119.
Check for earth on connection N of component 119.
Check the insulation and the continuity of the following connections:
●connection code 3MS,
●connection code 3MT,
between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Run a multiplex network test (see 88B, Multiplex).
If the computer still does not respond, contact the Techline.
AFTER REPAIRDeal with any faults detected by the diagnostic tool. Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.