check engine light RENAULT SCENIC 2009 J84 / 2.G Automatic Transmission AJ0 BVA Workshop Manual

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 28V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
DF023
PRESENT
OR
STOREDGEARBOX OIL TEMPERATURE SENSOR CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–in the event of open circuit or short circuit+:
–+ after ignition feed,
–oil temperature ≤ - 40 ˚C,
–vehicle speed > 6 mph (10 km/h).
–in the event of short circuit-:
–+ after ignition feed,
–oil temperature > 180 ˚C,
–vehicle speed > 6 mph (10 km/h).
–accelerator pedal > 12.5 % and engine speed > 305 rpm.
(detection time in the event of short circuit- is 10 minutes).
Effect on system:
–in the event of open circuit or short circuit+:
Gear change quality is reduced.
lock-up is inhibited.
–in the event of short circuit-:
The transmission operates as if the temperature had increased.
Customer complaint:
–in the event of open circuit or short circuit+:
If the fault occurs while driving, the transmission engages fixed 5th gear.
Restarting is in 3rd gear.
Gear change quality is reduced.
Fault warning light on
–in the event of short circuit-:
Fault warning light on
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Check that the coolant temperature (see 13B, Diesel injection, EDC16, CP33 M9R 721 Conformity check)
is ≥ - 40 ˚C (the transmission oil temperature sensor is within its operating range).
If the oil temperature ≤ - 40 ˚C, move on to step 1.
If the oil temperature is ≥ - 40 ˚C, deal with the fault; move on to step 2.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF023/AJ0_V05_DF023
MR-372-J84-23A000$405.mif

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 31V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
DF038
PRESENT
OR
STOREDTURBINE SPEED SENSOR CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–+ after ignition feed,
–with the engine running,
–vehicle speed > 24 mph (40 km/h),
–engine speed > 1500 rpm,
–turbine speed < 600 rpm and accelerator pedal > 0 %.
Effect on system:
Impossible to calculate gear.
Customer complaint:
Gear on which fault occurred is fixed. Restarting in fixed 3rd gear (no more gear
changes). Manual mode is inhibited. Fault warning light comes on.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Look for any damage to the wiring harness, and check the condition and connection of the transmission
computer and the turbine speed sensor.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + after ignition feed on connection AP4 of component 1060.
Is the + after ignition feed still present?
If YES, move on to step 1.
If NO, move on to step 2.
Step 1:
Check the continuity and insulation of the following connections:
●Connection code 5HN.
●Connection code 5DA.
Between components 119 and 1060.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the intermediate connector R22, if the fault is still present, replace component 1060.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF038/AJ0_V05_DF038

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 33V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
If the fault is stored:DF067
PRESENT
OR
STORED
LEVER POSITION SWITCH CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–in the event of open circuit or short circuit-:
–+ after ignition feed and change of lever position.
–in the event of short circuit+:
–+ after ignition feed, initial lever position: Position "P", "R", "N" or "D".
Effect on system:
The lever value is held at its previous valid position until the fault is confirmed. Then
the lever position becomes DRIVE (internal software variable) irrespective of the fault.
–If the fault is present and the lever in position "P", the transmission is in "N", hydraulic
neutral.
–If the fault is present and the lever in position "R", the transmission is in "R", hydraulic
reverse.
–If the fault is present and the lever in position "N", the transmission is in "N", hydraulic
neutral.
–If the fault is present and the lever in position "D", the transmission is in "D", hydraulic
forward gear.
lock-up is inhibited.
Customer complaint:
No lever position display on the instrument panel following fault confirmation and
starting impossible.
If the engine is already running when the fault occurs, there is jolting when shifting from
"P" or "N" to "R" or "D".
Fault warning light comes on.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Note:
It is possible to produce this fault if the driver or operator voluntarily keep the lever between two normal positions
for longer than 2 seconds.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF067/AJ0_V05_DF067

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 41V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
DF086
PRESENT
OR
STOREDEVS2 SEQUENCE SOLENOID VALVE CIRCUIT
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–in the event of short circuit+:
Lever in "Drive" position, gear engaged = 2, 3, 4, 5, 6,
and Inconsistency between the solenoid valve control status and the control voltage.
–in the event of open circuit:
Lever in "Drive" position, lock-up closed, gear engaged = 2, 3, 4, 5, 6,
and Inconsistency between the solenoid valve control status and the control voltage.
–in the event of short circuit-:
Lever in "Drive" position, lock-up open, gear engaged = 1, 2, 3, 4, 5, 6,
OR Gear 1 with engine braking,
and Inconsistency between the solenoid valve control status and the control voltage.
OR
Running command AC002 "Shift solenoid 2".
Effect on system:
–in the event of short circuit+:
If the fault appears with the lock-up closed, gear engaged in "Drive" position = 2, 3, 4,
5, 6, automatic transmission is locked.
–in the event of open circuit:
No effect.
–in the event of short circuit-:
Risk of stalling in 1st with engine braking.
Customer complaint:
If the fault occurs while driving, the transmission engages fixed 5th gear.
Restarting is in 3rd gear.
Fault warning light comes on.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Look for any damage to the harness and check the condition and connection of the automatic transmission
computer and automatic transmission connectors.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + after ignition feed on connection 5LW of component 754.
If + after ignition feed is present, move on to step 1.
If + after ignition feed is not present, move on to step 8.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF086/AJ0_V05_DF086

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 51V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
*EVS2 = sequence solenoid valve 2DF097
PRESENT
OR
STORED
CONVERTER lock-up
1.DEF: CONVERTER LOCK-UP CONTROL
NOTESOrder of priority in the event of more than one fault:
If there is a combination of the following faults:
–DF097 "Converter lock-up",
–DF086 "Sequence solenoid valve circuit "EVS2*""
–DF306 "Lock-up/brake 1 solenoid valve circuit",
deal first with faults DF086 "Sequence solenoid valve "EVS2*"" and DF306 "Lock-
up/brake 1 solenoid valve circuit".
Conditions for applying fault finding procedures to stored faults:
The fault is declared present after:
If in lock-up:
Lever in Manual position,
and difference in *slippage speed ≥ 40 + Vehicle speed / 2 for a certain time,
and EVS2* solenoid valve control status > 95 %.
In the event of slippage:
Lever in Manual position,
and difference in slippage speed ≥ 40 + slippage speed setpoint for a certain time,
and EVS2* solenoid valve control status > 95 %.
*slippage = engine speed - turbine speed
Effect on system:
Increase in oil temperature.
–In the event of engagement fault, lock-up inhibited.
–In the event of slippage fault, lock-up slippage inhibited.
Customer complaint:
Warning light on.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF097/AJ0_V05_DF097

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 58V3 MR-372-J84-23A000$450.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
DF108
PRESENT
OR
STOREDAVERAGE EFFECTIVE TORQUE MULTIPLEX SIGNAL
1.DEF: Multiplex frames absent or values invalid (fault with the computer generating
the signal or multiplex line connection fault)
NOTESCustomer complaint:
Fault warning light comes on.
If the fault occurs while driving, the transmission engages fixed 5th gear. Restarting
occurs in fixed 3rd gear (no more gear changes).
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Run a multiplex network test (see 88B, Multiplex).
Carry out a test on the engine management computer (see 13B, Diesel injection, Conformity check) (EDC16
CP33 M9R 721).
Check the continuity and insulation against earth of the following connections:
●Connection code 3MS.
●Connection code 3MT.
Between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF108/AJ0_V05_DF108
MR-372-J84-23A000$450.mif

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 63V3 MR-372-J84-23A000$450.mif
AJ0 BVA
Vdiag No.: 04, 05
DF186
PRESENT
OR
STOREDNO INJECTION MULTIPLEX SIGNAL
1.DEF: Multiplex frames absent or values invalid (fault with the computer generating
the signal or multiplex line connection fault)
NOTESEffect on system:
If the fault occurs while driving, the transmission engages fixed 5th gear.
Restarting occurs in fixed 3rd gear (no more gear changes).
Fault warning light comes on.
Customer complaint:
The line pressure is not being checked properly.
The lock-up is inhibited (still open).
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Run a multiplex network test (see 88B, Multiplex).
Carry out a test on the engine management computer (see 13B, Diesel injection, Conformity check)
(EDC16 CP33 M9R 721).
Check the continuity and insulation against earth of the following connections:
●Connection code 3MS.
●Connection code 3MT.
Between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF186/AJ0_V05_DF186

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 66V3 MR-372-J84-23A000$450.mif
AJ0 BVA
Vdiag No.: 04, 05
DF238
PRESENT
OR
STOREDINVALID RAW ENGINE TORQUE MULTIPLEX SIGNAL
1.DEF: Multiplex frames absent or values invalid (fault with the computer generating
the signal or multiplex line connection fault)
NOTESSystem effects:
The line pressure is not being checked properly.
Customer complaint:
Fault warning light comes on.
If the fault occurs while driving, the transmission engages fixed 5th gear.
Restarting occurs in fixed 3rd gear (no more gear changes).
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Run a multiplex network test (see 88B, Multiplex).
Carry out a test on the engine management computer (see 13B, Diesel injection, Conformity check)
(EDC16 CP33 M9R 721).
Check the continuity and insulation against earth of the following connections:
●Connection code 3MS.
●Connection code 3MT.
Between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF238/AJ0_V05_DF238

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 68V3 MR-372-J84-23A000$450.mif
AJ0 BVA
Vdiag No.: 04, 05
DF256
CONTINUED 1
Note:
To accurately locate components (see location of components).
NOTESCustomer complaint:
Switch to safe mode:
–If caused by brake 2 solenoid valve, system switches to fixed 2nd, 3rd or 5th gear
safe mode.
–If caused by clutch 2 solenoid valve, system switches to fixed 2nd, 3rd or 6th gear
safe mode.
–If caused by the clutch 3 solenoid valve, system switches to fixed 2nd, 3rd, 4th or 5th
gear safe mode.
–If caused by clutch 1 solenoid valve, system switches to fixed 3rd, 5th or 6th gear
safe mode.
In all cases, restarting is in 3rd gear.
If vehicle stopped in Drive, system switches to fixed 5th gear if engine speed is lower
than 2000 rpm.
If vehicle stopped in R, switch to R if engine speed is lower than 2000 rpm.
Fault warning light comes on.
Note:
If at least one solenoid valve is faulty, replace the hydraulic distributor.
Look for any damage to the wiring and check the condition and connection of the connectors for components 119
and 754.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 71V3 MR-372-J84-23A000$450.mif
AJ0 BVA
Vdiag No.: 04, 05
DF273
PRESENT
OR
STOREDCLUTCH 1 SOLENOID VALVE CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault appears after:
–in the event of short circuit+ or short circuit-:
Lever in "Drive" position, gear engaged = 1, 2, 3, 4, 5, 6 OR Gear engaged = 1 and
engine braking.
–in the event of open circuit:
Lever in "Drive" position, Gear engaged = 1, 2, 3, 4,
OR
Running command AC026 "Clutch 1 solenoid valve".
System effects:
–in the event of short circuit+:
No effect.
–in the event of open circuit or short circuit-:
If the fault occurs on gears 1 to 4, in D mode, the transmission switches to Neutral
(see DF256 Erratic gear jumps). Then system switches to fixed 5th gear mode after
the vehicle has stopped.
Customer complaint:
–in the event of short circuit+:
If the fault occurs while driving, the transmission engages fixed 5th gear.
Restarting in fixed 5th gear (no more gear changes).
Significant jolting during gear changes.
Fault warning light comes on.
–in the event of open circuit or short circuit-:
If the fault occurs while driving, the transmission engages fixed 5th gear.
Restarting in fixed 5th gear (gear change impossible)
Fault warning light comes on.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Look for any damage to the wiring harness, and check the condition and connection of the automatic
transmission computer and hydraulic distributor connectors.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + after ignition feed on connection 5LW of component 754.
Is the + after ignition feed still present?
If YES, move on to step 1.
If NO, move on to step 8.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF273/AJ0_V05_DF273