oil pressure RENAULT SCENIC 2009 J84 / 2.G Automatic Transmission AJ0 BVA Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: SCENIC, Model: RENAULT SCENIC 2009 J84 / 2.GPages: 162
Page 7 of 162
AUTOMATIC TRANSMISSION
Fault finding - List and location of components23A
23A - 7V3 MR-372-J84-23A000$090.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - List and location of components
*LS: line pressure.
*EVS: sequence solenoid valve.Number Description
1Oil temperature sensor
2Clutch 1 solenoid valve
3Clutch 2 solenoid valve
4Clutch 3 solenoid valve
5LS* pressure regulation solenoid valve
6"EVS1"* shift solenoid
7"EVS2"* shift solenoid
8Converter lock-up and brake 1 solenoid valve
9Brake 2 solenoid valve
10 Clutch 1 solenoid valve pressure switch
11 Clutch 2 solenoid valve pressure switch
12 Clutch 3 solenoid valve pressure switch
13 Brake 1 solenoid valve pressure switch
14 Brake 2 solenoid valve pressure switch
MR-372-J84-23A000$090.mif
Page 9 of 162
AUTOMATIC TRANSMISSION
Fault finding - Role of components
23A
23A - 9V3 MR-372-J84-23A000$135.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Role of components
Role of main automatic transmission components
Automatic transmission computer:
The gearbox computer is used to manage the entire system.
Its role is to define the optimum operating mode for the automatic transmission (modify the torque transmitted to the
drive wheels by the automatic transmission), inform the driver (instrument panel, information display, buzzer) and
communicate with the other computers.
To carry out this function, the transmission computer takes account of:
–the operation of the gearbox,
–signals exchanged with other computers,
–driver requests.
Transmission oil temperature sensor:
Its role is to inform the automatic transmission computer of the transmission oil temperature.
Transmission input speed sensor:
Its role is to inform the automatic transmission computer of the turbine speed.
Transmission output speed sensor:
Its role is to inform the automatic transmission computer of the vehicle speed.
Brake light switch:
Its role is to inform the automatic transmission computer that the driver has depressed the brake pedal.
Multifunction switch:
Its role is to inform the automatic transmission computer of the gear lever position.
Shift-lock:
The role of this function is to lock the lever in position "P" and to immobilise the vehicle when stationary.
Solenoid valves:
The solenoid valves are fitted in the factory and cannot be removed from the hydraulic distributor to ensure optimum
gearbox operation, therefore they cannot be replaced separately.
The automatic transmission has two types of solenoid valve:
–2 "all or nothing" solenoid valves,
–6 "progressive" solenoid valves.
Of these 8 solenoid valves, 7 are used to control gear changes in automatic and manual modes, and one solenoid
valve controls the oil pressure in the automatic transmission hydraulic distributor.
Instrument panel display:
The purpose of this function is to manage the transmission of multiplex line signals required for the instrument panel
display.
On the instrument panel:
–a fault warning light,
–a message on the instrument panel in case of irregularity,
–an information display: gear lever position/gear engaged/brake pedal depressed indicator light/lever position in P
or N request indicator light.
On the gear lever:
–Position: P / R / N / D / M+/-,
–Shift-lock: lever lock.
MR-372-J84-23A000$135.mif
Page 10 of 162
AUTOMATIC TRANSMISSION
Fault finding - Operating diagram
23A
23A - 10V3 MR-372-J84-23A000$180.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Operating diagram
Line pressure
OIL PUMP
Hydraulic
distributor
Primary regulation valve (pressure regulating valve)
LS pressure regulation solenoid valve
Manual valve
Clutch
modulating
solenoid valve 1
Clutch
modulating
solenoid valve 2Clutch
modulating
solenoid valve 3Brake
modulating
solenoid valve 2Modulating solenoid
valve
lock-up/brake 1
Sequence
solenoid valve 1Sequence solenoid
valve 2
Clutch 1 Clutch 2 Clutch 3 Brake 2Brake
1Torque
converter
lock-up
Hydraulic receivers
MR-372-J84-23A000$180.mif
Page 16 of 162
AUTOMATIC TRANSMISSION
Fault finding - Role of components
23A
23A - 16V3 MR-372-J84-23A000$225.mif
AJ0 BVA
Vdiag No.: 04, 05
"PRESSURE CONTROL" FUNCTION:
Purpose of this function:
The purpose of this function is to regulate the oil pressure inside the transmission hydraulic distributor.
"Lever selection"
function
"Pressure
control"
function Oil temperature
Line pressure solenoid
valve
Vehicle speed
Turbine speed
–Accelerator pedal
position
–Engine speed
–Engine torqueCAN
"Gear change" function
Page 17 of 162
AUTOMATIC TRANSMISSION
Fault finding - Role of components
23A
23A - 17V3 MR-372-J84-23A000$225.mif
AJ0 BVA
Vdiag No.: 04, 05
"CONVERTER lock-up" FUNCTION:
Aim of this function: The aim of this function is to lock up the converter.
–lock-up/release definition:
The converter is a hydraulic clutch which provides a hydraulic connection between the engine and the automatic
transmission pressure plate.
The purpose of the lock-up function is to lock the turbine and the converter casing together, transforming a hydraulic
connection into a mechanical connection. The role of the lock-up function is to prevent slipping losses.
EVS2*: sequence solenoid valve 2."Lever selection"
function
"Converter
lock-up"
functionLock-up and brake 1
solenoid valve
Solenoid valve EVS2*
Oil temperature
Vehicle speed
Turbine speed
Brake pedal action
"Torque management"
function
–Accelerator pedal
position
–Engine speed
–Engine torqueCAN
"Gear change" function
Page 21 of 162
AUTOMATIC TRANSMISSION
Fault finding - Replacement of components
23A
23A-21V3 MR-372-J84-23A000$270.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Replacement of components
*sig.: signal
*EVS1 = shift solenoid valve 1
*EVS2 = shift solenoid valve 2
*LS = line pressure regulation solenoid valveTool fault Diagnostic tool title Defect modes
DF023Transmission oil temperature sensor
circuit–in the event of open circuit or short circuit+:
If the fault occurs while driving, the
transmission engages fixed 5
th gear.
Restarting is in 3rd gear.
–in the event of short circuit-:
No defect mode.
DF038Turbine speed sensor circuit If the fault occurs while driving:
Gear fixed. Restarting is in fixed 3
rd gear.
DF067Lever switch circuit No defect mode.
DF084Multiplex network If the fault occurs while driving, the
transmission engages fixed 5
th gear.
Restarting is in 3rd gear.
DF085EVS1 shift solenoid valve circuit – in the event of open circuit or short circuit+:
Fixed 5
th gear engaged.
Restarting is in 5th gear.
–in the event of short circuit-:
No defect mode.
DF086ESV2* shift solenoid valve circuit Fixed 5
th gear engaged.
Restarting is in 3rd gear.
DF091"LS"* pressure regulation solenoid
valve circuitNo defect mode.
DF093Manual sequential controls circuit No defect mode.
DF095Gear lever lock electromagnet circuit No defect mode.
DF097Converter lockup No defect mode.
DF108Effective average torque multiplex
signalIf the fault occurs while driving, the gearbox
engages fixed 5
th gear. Restarting is in 3rd
gear.
DF171Vehicle speed sensor circuit If the fault occurs while driving:
Gear fixed. Restarting is in fixed 3
rd gear.
DF178Accelerator pedal position No defect mode.
DF183No UCH multiplex signal. No defect mode.
DF186No injection multiplex signal If the fault occurs while driving, the gearbox
engages fixed 5
th gear.
Restarting is in 3rd gear.
DF230Signal: multiplex speed vehicle invalid No defect mode.
MR-372-J84-23A000$270.mif
Page 24 of 162
AUTOMATIC TRANSMISSION
Fault finding - Replacement of components
23A
23A-24V3 MR-372-J84-23A000$270.mif
AJ0 BVA
Vdiag No.: 04, 05
Replacing the transmission computer:
Remove the automatic transmission computer (see MR 370 mechanical, 23A, Automatic transmission,
Automatic transmission computer, Removal - Refitting).
Refit the automatic transmission computer (see MR 370 mechanical, 23A, Automatic transmission,
Automatic transmission computer, Removal - Refitting).
Establish dialogue with the diagnostic tool.
Use command VP001 Enter VIN.
Run command VP009 Write last After-Sales Service operation date.
Do not carry out any automatic programming if replacing the automatic transmission computer. Automatic
programming is finalised when the vehicle is driven.
In order to optimise the automatic programming before delivering the vehicle to the customer, apply the
"Programming procedure" shown below.
Replacing the hydraulic distributor:
Remove the transmission hydraulic distributor (see MR 370 mechanical, 23A, Automatic transmission,
Hydraulic distributor, Removal - Refitting).
Refit the transmission hydraulic distributor (see MR 370 Mechanical, 23A, Automatic transmission, Hydraulic
distributor, Removal - Refitting).
Replacing the automatic transmission
Remove the transmission (see MR 370,Mechanical, 23A, Automatic transmission, Removal - Refitting).
Refit the transmission (see MR 370, Mechanical, 23A, Automatic transmission, Removal - Refitting).
Establish communication with the diagnostic tool.
Initialise all the programming, use the command RZ009 Self-adapting clearing (Vdiag05 only).
Run command VP009 Write last After-Sales Service operation date.
The self-programming functions are performed when the vehicle is being driven.
In order to optimise the automatic programming before delivering the vehicle to the customer, apply the
"Programming procedure" shown below.
* APV: After-SalesPROGRAMMING PROCEDURE:
Programming conditions:
The automatic gearbox oil temperature should be between 60˚C and 100˚C.
Stationary, engine running, brake pedal depressed:
Engage neutral at least 5 times to consolidate the programming.
While driving:
Engage the same gear at least 5 times (i.e. in the same conditions) to consolidate the programming.
Note:
Gear changes are slow and harsh the first few times the vehicle is driven, until the automatic transmission computer
has carried out its automatic programming.
During upshifts and downshifts, the system analyses variations in oil pressure, components (play in the brakes and
clutches, changes to spring stiffness due to ageing) and input torque, then corrects them in order to maintain the
quality of gear changes.
The system analyses the turbine speed during the 3 phases of drag reduction (selection of Neutral when stationary,
regulation during drag reduction and deselection of Neutral) and corrects this speed by adjusting the converter
lock-up solenoid valve pressure.
Page 26 of 162
AUTOMATIC TRANSMISSION
Fault finding - Fault summary table
23A
23A - 26V3 MR-372-J84-23A000$360.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Fault summary table
*signal: signal
*EVS1 = sequence solenoid valve 1
*EVS2 = sequence solenoid valve 2
*LS = line pressure regulation solenoid valveTool fault Associated DTC Diagnostic tool title
DF023710 Transmission oil temperature sensor circuit
DF038715 Turbine speed sensor circuit
DF067705 Lever position switch circuit
DF084C073 Multiplex network
DF0851753 EVS1* shift solenoid circuit
DF0861758 "ESV2"* shift solenoid circuit
DF091748 "LS"* pressure regulation solenoid valve circuit
DF093826 Manual sequential controls circuit
DF095928 Gear lever lock electromagnet circuit
DF097740 Converter lock-up
DF1085300 Effective average torque multiplex signal
DF171720 Vehicle speed sensor circuit
DF1785600 Accelerator pedal position
DF183C140 No UCH multiplex signal
DF186C100 No injection multiplex signal
DF230C415 Invalid vehicle speed multiplex signal
DF236725 Invalid engine speed multiplex signal
DF2384073 Invalid raw engine torque multiplex signal*
DF256730 Erratic gear jumping
DF273753 Clutch 1 solenoid valve circuit
DF274763 Clutch 2 solenoid valve circuit
DF275768 Clutch 3 solenoid valve circuit
DF2891840 Automatic transmission multiplex signal
DF290C121 Multiplexed ABS signal
DF298893 Gear shifts
DF300758 Brake 2 solenoid valve circuit
DF301751 Clutch 1 pressure switch circuit
MR-372-J84-23A000$360.mif
Page 47 of 162
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 47V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
DF091
CONTINUED 2
Stage 4:
Drain the automatic transmission (see, MR 370, Mechanical, 23A Automatic transmission, Oil change) and
remove the transmission housing (see, MR 370, Mechanical, 23A Automatic transmission, Hydraulic
distributor).
Disconnect the connector from component 754, measure the resistance of the LS pressure regulation solenoid
valve (on the connector of the internal wiring harness of the transmission) between the following connections:
●Connection code 5BU.
●Connection code 5LW.
The resistance must be 5.3 ΩΩ Ω Ω
± 0.5 ΩΩ Ω Ω
at 20 ˚C.
Is the resistance correct?
If YES, move on to step 5.
If NO, move on to step 6.
Stage 5:
Measure the continuity and insulation of the following connections:
●Connection code 5BU.
●Connection code 5LW.
Between components R22 and the internal connector in the transmission.
Are the continuity and insulation correct?
If YES, contact the Techline.
If NO, replace the intermediate wiring harness between connector R22 and the internal connector in the
transmission.
Stage 6:
Disconnect the connector from resistance of the LS pressure regulation solenoid valve measure the LS
pressure regulation solenoid valve between the following connections:
●Connection code 5BU.
●Connection code 5LW.
The resistance must be 5.3 ΩΩ Ω Ω
± 0.5 ΩΩ Ω Ω
at 20 ˚C.
Is the resistance correct?
If YES, move on to step 7.
If NO, replace the hydraulic distributor.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
Page 93 of 162
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 93V3 MR-372-J84-23A000$495.mif
AJ0 BVA
Vdiag No.: 04, 05
DF301
CONTINUED
Step 1:
Drain the automatic transmission (see, MR 370, Mechanical, 23A Automatic transmission, Oil change) and
remove the transmission housing (see, MR 370, Mechanical, 23A Automatic transmission, Hydraulic
distributor).
Check the continuity and insulation of the following connections on the internal wiring harness:
●Connection code 5CZ, between components 119 and the pressure switch on clutch 1.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Are the continuity and insulation correct?
If YES, replace the pressure switch on clutch 1.
If NO, replace the internal wiring harness.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.